Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM › 2012.03–2016.05
RM2070E _57 Power Source / Network _061936 NETWORKING _0301753 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B2789  No Response from ID BOX  


DESCRIPTION

This DTC is stored when LIN communication between the certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU) stops for 10 seconds or more.

DTC No. DTC Detection Condition Trouble Area
B2789 No communication between certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU) for 10 seconds or more.
·

ID code box (immobiliser code ECU)

·

Certification ECU (smart key ECU assembly)

·

Wire harness or connector

·

ECU-B2 fuse



WIRING DIAGRAM

B315276E01
0.904,2.57 2.448,2.882 1.545,0.312 10 Certification ECU (Smart Key ECU Assembly) 3.931,2.57 5.470,2.892 1.539,0.323 10 ID Code Box (Immobiliser Code ECU) 0.904,2.406 1.189,2.553 0.286,0.147 10 L62 3.945,2.406 4.240,2.544 0.295,0.137 10 L10 1.87,1.479 2.112,1.633 0.242,0.154 10 LIN 4.224,1.479 4.558,1.633 0.334,0.154 10 LIN1 2.141,1.346 2.325,1.511 0.184,0.165 10 29 4.065,1.346 4.201,1.511 0.136,0.165 10 3 4.904,1.09 5.101,1.244 0.197,0.154 10 +B 4.794,2.028 5.128,2.182 0.334,0.154 10 GND 5.171,0.994 5.272,1.159 0.100,0.165 10 1 5.171,1.925 5.290,2.090 0.119,0.165 10 8 5.613,1.234 6.201,1.371 0.588,0.137 10 ECU-B2 4.359,0.393 5.726,0.568 1.367,0.174 10 from Auxiliary Battery 0.701,3.488 2.329,3.635 1.628,0.147 10 : LIN Communication Line

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

If the certification ECU (smart key ECU assembly) is replaced, register the key.

·

If the ID code box (immobiliser code ECU) is replaced, register the ECU code and ECU communication ID.

·

When using the GTS to troubleshoot with the power switch off:

Connect the GTS to the DLC3, and turn the courtesy switch on and off at 1.5-second intervals until communication between the GTS and vehicle begins.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (ID CODE BOX - AUXILIARY BATTERY AND BODY GROUND)
a.
U190806E02
0.667,0.948 1.198,1.479 false 2.26,1.479 2.698,0.948 false 0.208,0.125 0.406,0.302 0.198,0.177 10 false *1 0.5,1.302 0.76,1.583 0.26,0.281 10 false L10 0.448,0.833 0.688,1 0.24,0.167 10 false +B 2.729,0.854 3.063,1.021 0.333,0.167 10 false GND

Disconnect the L10 ID code box connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L10-8 (GND) - Body ground Always Below 1 Ω


Standard Voltage:
Tester Connection Condition Specified Condition
L10-1 (+B) - Body ground Power switch off 11 to 14 V


Text in Illustration
*1 Front view of wire harness connector
(to ID Code Box (Immobiliser Code ECU))



OK

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - ID CODE BOX)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - ID CODE BOX)
a.

Disconnect the L62 certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L62-29 (LIN) - L10-3 (LIN1) Always Below 1 Ω
L62-29 (LIN) - Body ground Always 10 kΩ or higher




OK

3.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)
a.

Replace the ID code box (immobiliser code ECU).



NEXT

4.CHECK DTC OUTPUT
4.CHECK DTC OUTPUT

b.

Recheck for DTCs.

OK:

DTC B2789 is not output.




OK

END (ID CODE BOX (IMMOBILISER CODE ECU) WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)