Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM › 2013.08–2014.11
RM2070E _57 Power Source / Network _061936 NETWORKING _0301753 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B2322  Front Passenger Side Door ECU Communication Stop  


DESCRIPTION

This DTC is stored when LIN communication between the power window regulator motor assembly (for front passenger side) and main body ECU (multiplex network body ECU) stops for 10 seconds or more.

DTC No. DTC Detection Condition Trouble Area
B2322 No communication between power window regulator motor assembly (for front passenger side) and main body ECU (multiplex network body ECU) for 10 seconds or more.
·

Power window regulator motor assembly (for front passenger side)

·

Main body ECU (multiplex network body ECU)

·

Instrument panel junction block assembly

·

Wire harness or connector

·

P FR DOOR fuse



WIRING DIAGRAM

B220667E29
4.208,1.797 6.597,2.124 2.390,0.327 10 Power Window Regulator Motor Assembly (for Front Passenger Side) 4.208,1.653 5.085,1.799 0.877,0.147 10 N2*1, O2*2 2.773,2.325 3.282,2.472 0.509,0.147 10 *1: LHD 3.47,2.325 4.012,2.472 0.542,0.147 10 *2: RHD 4.607,0.597 4.702,0.733 0.095,0.136 10 9 2.172,0.597 2.347,0.733 0.176,0.136 10 16 3.131,0.597 3.307,0.733 0.176,0.136 10 27 5.721,0.536 5.817,0.673 0.096,0.136 10 2 5.721,1.376 5.818,1.512 0.097,0.136 10 1 4.773,0.466 5.012,0.613 0.239,0.147 10 LIN 1.789,0.466 2.102,0.613 0.313,0.147 10 LIN2 0.624,0.857 0.869,1.010 0.245,0.153 10 MB 0.624,1.016 2.273,1.346 1.649,0.329 10 Main Body ECU (Multiplex Network Body ECU) 0.569,1.671 0.769,1.824 0.200,0.153 10 2A 0.559,1.804 3.231,1.957 2.672,0.153 10 Instrument Panel Junction Block Assembly 0.445,2.482 2.066,2.635 1.621,0.153 10 : LIN Communication Line 5.564,0.466 5.680,0.613 0.115,0.147 10 B 5.345,1.289 5.678,1.436 0.333,0.147 10 GND 6.059,0.552 6.872,0.694 0.813,0.142 10 P FR DOOR

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

When a power window regulator motor assembly is replaced or removed and reinstalled, it requires initialization (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION).

·

When using the GTS to troubleshoot with the power switch off:

Connect the GTS to the DLC3, and turn the courtesy switch on and off at 1.5-second intervals until communication between the GTS and vehicle begins.



PROCEDURE

1.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).

U190812E02
2.042,1.698 2.667,2.219 true 5.385,1.708 6.063,2.229 true 0.24,0.156 0.448,0.323 0.208,0.167 10 false *1 4.854,0.156 5.063,0.323 0.208,0.167 10 false *2 1.917,1.167 2.156,1.313 0.24,0.146 10 false MB 5.594,0.906 5.792,1.052 0.198,0.146 10 false 2A 5.938,2.24 6.302,2.417 0.365,0.177 10 false LIN2 2.542,2.219 2.906,2.396 0.365,0.177 10 false LIN2


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

HINT:

This inspection is to check the LIN line in the instrument panel junction block assembly that connects the wire harness to the built-in main body ECU (multiplex network body ECU).


Standard Resistance:
Tester Connection Condition Specified Condition
2A-27 (LIN2) - MB-16 (LIN2) Always Below 1 Ω
2A-27 (LIN2) - Body ground Always 10 kΩ or higher


Text in Illustration
*1 Component without harness connected
(Instrument panel Junction Block Assembly)
*2 Component without harness connected
(Instrument Panel Junction Block Assembly)



OK

2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - POWER WINDOW REGULATOR MOTOR)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - POWER WINDOW REGULATOR MOTOR)
a.

Disconnect the N2*1 or O2*2 power window regulator motor assembly (for front passenger side) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2A-27 (LIN2) - N2-9 (LIN)*1
2A-27 (LIN2) - O2-9 (LIN)*2
Always Below 1 Ω
2A-27 (LIN2) - Body ground Always 10 kΩ or higher


*1: for LHD

*2: for RHD




OK

3.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR - AUXILIARY BATTERY, BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR - AUXILIARY BATTERY, BODY GROUND)
a.
U190797E02
1.531,1.198 0.979,0.49 true 1.917,1.219 2.479,0.521 true 0.656,1.188 0.917,1.365 0.26,0.177 10 false N2 2.479,0.365 2.635,0.677 0.156,0.313 10 false B 0.656,0.365 1.073,0.625 0.417,0.26 10 false GND 0.583,0.063 0.75,0.313 0.167,0.25 10 false *1 0.656,1.458 0.917,1.688 0.26,0.229 10 false O2 0.979,1.188 1.198,1.427 0.219,0.24 10 false *2 0.979,1.458 1.146,1.667 0.167,0.208 10 false *3

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
N2-2 (B) - Body ground*1
O2-2 (B) - Body ground*2
Power switch off 11 to 14 V



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N2-1 (GND) - Body ground*1
O2-1 (GND) - Body ground*2
Always Below 1 Ω


*1: for LHD

*2: for RHD


Text in Illustration
*1 Front view of wire harness connector
(to Power Window Regulator Motor Assembly (for Front Passenger Side))
*2 for LHD
*3 for RHD



OK

4.REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for FRONT PASSENGER SIDE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for FRONT PASSENGER SIDE)
a.

Replace the power window regulator motor assembly (for front passenger side) (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR (for Front Door)>REMOVAL).



NEXT

5.CHECK DTC OUTPUT
5.CHECK DTC OUTPUT

b.

Check for DTCs.

OK:

DTC B2322 is not output.




OK

END (POWER WINDOW REGULATOR MOTOR ASSEMBLY WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)