Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU) › 2016.05–2017.12
RM2070E _57 Power Source / Network _061936 NETWORKING _0301754 CAN COMMUNICATION SYSTEM(w/o Central Gateway ECU) D

NETWORKING  CAN COMMUNICATION SYSTEM(w/o Central Gateway ECU)  SYSTEM DESCRIPTION  


BRIEF DESCRIPTION


a.

The Controller Area Network (CAN) is a serial data communication system for real time application. It is a vehicle multiplex communication system which has a high communication speed and the ability to detect malfunctions.

C238999E01
0.209,2.062 1.143,2.208 0.934,0.145 10 CAN Main Bus 1.167,2.131 1.424,2.131 1.424,2.131 1.424,1.772 false 3.435,3.183 4.226,3.329 0.791,0.145 10 CAN Branch 4.249,3.252 4.507,3.252 4.507,3.252 4.745,3.019 false 1.421,3.66 3.257,3.805 1.836,0.145 10 : CAN Main Bus Line (CANH) 1.421,4.094 3.257,4.239 1.836,0.145 10 : CAN Main Bus Line (CANL) 4.825,3.66 6.523,3.805 1.698,0.145 10 : CAN Branch Line (CANH) 4.825,4.094 6.523,4.239 1.698,0.145 10 : CAN Branch Line (CANL) 1.712,2.63 2.090,2.775 0.378,0.145 10 DLC3 3.393,2.63 3.712,2.775 0.319,0.145 10 ECU 5.312,2.63 5.631,2.775 0.319,0.145 10 ECU


b.

Using the CANH and CANL bus lines as a pair, CAN communication is performed using a voltage differential. (A base voltage is applied to the pair of lines and a voltage differential is created when communicating.)


c.

Many ECUs or sensors installed to the vehicle operate by sharing information and communicating with each other.


d.

The CAN has two resistors of 120 Ω which are necessary to enable communication.



DEFINITION OF TERMS


a.

Main bus

i.

The main bus is a wire harness between the two terminating resistors on the bus. This is the main bus in the CAN communication system.



b.

Branch

i.

A branch is a wire harness which diverges from the main bus to an ECU or sensor.



c.

Terminating resistors

i.

Two resistors of 120 Ω are installed in parallel across the ends of the CAN main bus lines. They are called terminating resistors. These resistors allow the changes of the voltage differential between the CAN bus lines to be accurately judged. To allow proper function of CAN communication, it is necessary to have both terminating resistors installed. Since the two resistors are installed in parallel, this results in a measurement of approximately 60 Ω.




ECUS OR SENSORS WHICH COMMUNICATE THROUGH CAN COMMUNICATION SYSTEM


a.

V Bus

i.

ECM


ii.

Brake booster with master cylinder assembly (Skid control ECU)


iii.

Main body ECU (Multiplex network body ECU)


iv.

Power steering ECU assembly


v.

Certification ECU (Smart key ECU assembly)


vi.

Airbag ECU assembly


vii.

Spiral cable with sensor sub-assembly (Steering angle sensor)


viii.

Hybrid vehicle control ECU


ix.

Transmission control ECU assembly


x.

Combination meter sub-assembly


xi.

Navigation receiver assembly*1


xii.

Radio and display receiver assembly*2


xiii.

Air conditioning amplifier assembly



b.

Sub bus 15

i.

Hybrid vehicle control ECU


ii.

ECM


iii.

Brake booster with master cylinder assembly (Skid control ECU)

HINT:

*1: for Navigation Receiver Type

*2: for Radio and Display Type





CIRCUIT DESCRIPTION


a.

The V bus and sub bus 15 each have termination circuits with two resistors of 120 Ω.



TROUBLESHOOTING REMARKS


a.

DTCs for the CAN communication system can be checked using the GTS. The DLC3 is connected to the CAN communication system, but no DTCs exist regarding problems in the DLC3 or the DLC3 branch lines. If there is a malfunction in the DLC3 or the DLC3 branch lines, ECUs on the CAN cannot output DTCs to the GTS.


b.

Malfunction in the CAN V bus (communication lines) can be checked by measuring the resistance between terminals of the DLC3. However, an open circuit in a branch line other than the DLC3 branch lines cannot be checked from the DLC3 (except branch line of the DLC3).

NOTICE:

Do not insert the tester probes directly into the DLC3. Be sure to use service wires.




DIAGNOSTIC TROUBLE CODES FOR CAN COMMUNICATION SYSTEM


HINT:

See Diagnosis System (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>DIAGNOSIS SYSTEM).



HOW TO DISTINGUISH CONNECTOR OF CAN JUNCTION CONNECTOR


a.

In the CAN communication system, the shape of connectors connected to the CAN junction connector which has an earth terminal are the same. The connectors connected to the CAN junction connector can be distinguished by the colors of the bus lines and the connecting side of the junction connector.

HINT:

See Terminals of ECU for bus line color or the shape of connectors (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>TERMINALS OF ECU).