Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU) › 2012.03–2014.11
RM2070E _57 Power Source / Network _061936 NETWORKING _0301754 CAN COMMUNICATION SYSTEM(w/o Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(w/o Central Gateway ECU)  ECM Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
ECM Communication Stop Mode Either condition is met:
·

"ECM (Engine)" is not displayed on the "CAN Bus Check" screen of the GTS (See page (Click here))

·

Communication system DTCs (DTCs that start with U) that are output correspond to "ECM Communication Stop Mode" in "DTC Combination Table" (See page (Click here))


·

Power source circuit of ECM

·

ECM main line or connector

·

ECM ground circuit

·

ECM



WIRING DIAGRAM

C240414E12
2.427,3.052 1.813,2.438 1.813,2.438 1.646,2.438 false 3.385,3.052 3.76,1.729 3.76,1.729 3.927,1.729 false 1.958,4.563 2.031,5.177 2.031,5.177 2.24,5.177 false 5.063,5.021 6.667,5.427 1.604,0.406 10 false Trouble Area 2.396,2.292 2.948,2.51 0.552,0.219 10 false DLC3 1.26,0.604 3.76,0.938 2.5,0.333 10 false : CAN Main Bus Line (CANH) 1.26,0.948 3.76,1.281 2.5,0.333 10 false : CAN Main Bus Line (CANL) 4.344,0.604 5.135,0.938 0.792,0.333 10 false *1: for LHD 4.344,0.948 5.135,1.281 0.792,0.333 10 false *2: for RHD 1.26,1.281 2.99,1.615 1.729,0.333 10 false : CAN Branch Line (CANH) 1.26,1.625 2.99,1.958 1.729,0.333 10 false : CAN Branch Line (CANL) 4.625,4.594 5.125,4.917 0.5,0.323 10 false ECM 2.281,5.104 4.344,5.25 2.063,0.146 10 false CAN No. 3 Junction Connector*1 2.281,5.448 4.344,5.594 2.063,0.146 10 false CAN No. 1 Junction Connector*2 0.375,4.594 1.625,4.76 1.25,0.167 10 false Meter Circuit Plate 5.135,3.146 5.323,3.323 0.188,0.177 10 false +B 5.063,3.542 5.333,3.719 0.271,0.177 10 false +B2 4.948,3.99 5.333,4.167 0.385,0.177 10 false IGSW 5.167,4.375 5.354,4.552 0.188,0.177 10 false E1 4.375,3.74 4.76,3.917 0.385,0.177 10 false CANL 4.375,3.115 4.781,3.292 0.406,0.177 10 false CANH 0.885,4.031 1.281,4.208 0.396,0.177 10 false 120 Ω 4.448,4.115 4.844,4.292 0.396,0.177 10 false 120 Ω 5.406,3.135 5.667,3.313 0.26,0.177 10 false A57 5.406,3.521 5.667,3.698 0.26,0.177 10 false A57 5.406,3.979 5.667,4.156 0.26,0.177 10 false A57 5.396,4.375 5.667,4.552 0.271,0.177 10 false D28 4.052,3.844 4.313,4.021 0.26,0.177 10 false A57 4.052,3.208 4.313,3.385 0.26,0.177 10 false A57 5.49,2.948 5.646,3.125 0.156,0.177 10 false 2 5.49,3.344 5.646,3.521 0.156,0.177 10 false 1 5.458,3.771 5.625,3.948 0.167,0.177 10 false 28 5.406,4.188 5.656,4.365 0.25,0.177 10 false 104 4.094,3.031 4.26,3.208 0.167,0.177 10 false 13 4.135,3.677 4.292,3.854 0.156,0.177 10 false 5 6.156,3.979 6.542,4.323 0.385,0.344 10 false IGN Fuse 5.406,2.635 6.688,2.885 1.281,0.25 10 false to EFI MAIN Relay 0.365,2.365 1.646,2.729 1.281,0.365 10 false CAN No. 2 Junction Connector 3.969,1.656 6.031,2.021 2.063,0.365 10 false CAN No. 1 Junction Connector*1 3.969,2.01 6.031,2.375 2.063,0.365 10 false CAN No. 3 Junction Connector*2 0.125,0.094 0.656,0.302 0.531,0.208 12 false V Bus: 0.104,4.583 0.563,4.781 0.458,0.198 10 false L27

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the power switch on (IG), turn the cruise control system on using the cruise control switch (ON/OFF switch), and wait at least 20 seconds.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>DIAGNOSIS SYSTEM).



HINT:
·

Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (ECM MAIN LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
U154226E02
1.781,1.667 1.365,2.573 false 1.406,1.021 1.781,1.583 false 0.146,0.104 0.917,0.427 0.771,0.323 10 false *a 0.25,1.781 0.531,1.948 0.281,0.167 10 false A57 1.01,0.927 1.542,1.073 0.531,0.146 10 false CANL 1.094,2.615 1.552,2.76 0.458,0.146 10 false CANH

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A57-13 (CANH) - A57-5 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to ECM)



OK

2.CHECK ECM POWER SOURCE CIRCUIT

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (ECM MAIN LINE)

2.CHECK ECM POWER SOURCE CIRCUIT

OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)