Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU) › 2016.05–2020.08
RM2070E _57 Power Source / Network _061936 NETWORKING _0301754 CAN COMMUNICATION SYSTEM(w/o Central Gateway ECU) C

NETWORKING  CAN COMMUNICATION SYSTEM(w/o Central Gateway ECU)  U0100  Lost Communication with ECM / PCM "A"  U0129  Lost Communication with Brake System Control Module  U0293  Lost Communication with Hybrid Vehicle Control System  


DESCRIPTION

·

The hybrid vehicle control ECU communicates with the ECM and brake booster with master cylinder assembly (skid control ECU). When the hybrid vehicle control ECU does not receive data from the ECM or brake booster with master cylinder assembly (skid control ECU), the hybrid vehicle control ECU stores DTC U0100 or U0129.

·

The ECM communicates with the hybrid vehicle control ECU. When the ECM does not receive data from the hybrid vehicle control ECU, the ECM stores DTC U0293.

·

The brake booster with master cylinder assembly (skid control ECU) communicates with the hybrid vehicle control ECU. When the brake booster with master cylinder assembly (skid control ECU) does not receive data from the hybrid vehicle control ECU, the brake booster with master cylinder assembly (skid control ECU) stores DTC U0293.


DTC No. DTC Detection Condition Trouble Area
U0100 The hybrid vehicle control ECU does not receive data from the ECM.
·

Open or short in sub bus 15 main line or connector

·

Open or short in sub bus 15 branch line or connector

·

Power source circuit of hybrid vehicle control ECU

·

Hybrid vehicle control ECU

·

Power source circuit of ECM

·

ECM

·

Open or short in CAN No. 1 junction connector

·

Open or short in CAN No. 5 junction connector


U0129 The hybrid vehicle control ECU does not receive data from the brake booster with master cylinder assembly (skid control ECU).
·

Open or short in sub bus 15 main line or connector

·

Open or short in sub bus 15 branch line or connector

·

Power source circuit of ECM

·

ECM

·

Power source circuit of hybrid vehicle control ECU

·

Hybrid vehicle control ECU

·

Power source circuit of brake booster with master cylinder assembly (skid control ECU)

·

Brake booster with master cylinder assembly (skid control ECU)

·

Open or short in CAN No. 1 junction connector

·

Open or short in CAN No. 5 junction connector


U0293
·

The ECM does not receive data from the hybrid vehicle control ECU.

·

The brake booster with master cylinder assembly (skid control ECU) does not receive data from the hybrid vehicle control ECU.


·

Open or short in sub bus 15 main line or connector

·

Open or short in sub bus 15 branch line or connector

·

Power source circuit of ECM

·

ECM

·

Power source circuit of brake booster with master cylinder assembly (skid control ECU)

·

Brake booster with master cylinder assembly (skid control ECU)

·

Open or short in CAN No. 1 junction connector

·

Open or short in CAN No. 5 junction connector



HINT:

This diagnostic procedure is for when DTC U0100, U0129 and U0293 are output at the same time.


WIRING DIAGRAM

C353281E04
5.24,0.219 6.615,0.417 1.375,0.198 10 false x: Suspected Area 3.385,0.5 4.01,0.708 0.625,0.208 10 false 120 Ω 0.74,0.646 2.594,1.021 1.854,0.375 10 false Hybrid Vehicle Control ECU 0.51,0.646 0.76,0.833 0.25,0.188 10 false L6 2.75,1.073 3.188,1.26 0.438,0.188 10 false CA3N 4.063,1.073 4.5,1.26 0.438,0.188 10 false CA3P 2.99,1.313 3.208,1.5 0.219,0.188 10 false 30 4.042,1.313 4.26,1.5 0.219,0.188 10 false 31 2.958,1.698 3.177,1.885 0.219,0.188 10 false W 4.073,1.698 4.292,1.885 0.219,0.188 10 false B 0.625,2.625 2.729,2.875 2.104,0.25 10 false CAN No. 5 Junction Connector 4.427,4.729 6.531,4.979 2.104,0.25 10 false CAN No. 1 Junction Connector 3.052,2.104 3.365,2.323 0.313,0.219 10 false L102 3.802,2.104 4.115,2.323 0.313,0.219 10 false L102 3.042,3.552 3.354,3.771 0.313,0.219 10 false L101 2.885,2.115 3.104,2.302 0.219,0.188 10 false 3 4.188,2.104 4.406,2.292 0.219,0.188 10 false 5 2.865,3.573 3.083,3.76 0.219,0.188 10 false 4 4.188,3.573 4.406,3.76 0.219,0.188 10 false 2 2.969,3.854 3.188,4.042 0.219,0.188 10 false Y 4.094,3.854 4.313,4.042 0.219,0.188 10 false R 3.052,4.156 3.438,4.385 0.385,0.229 10 false L132 4.198,4.167 4.417,4.354 0.219,0.188 10 false 3 2.875,4.177 3.094,4.365 0.219,0.188 10 false 9 2.573,4.719 2.885,4.938 0.313,0.219 10 false A67 2.656,4.552 2.875,4.74 0.219,0.188 10 false 3 2.667,5.302 2.885,5.49 0.219,0.188 10 false 9 2.813,5.635 3.031,5.823 0.219,0.188 10 false 10 4.198,5.625 4.417,5.813 0.219,0.188 10 false 4 1.906,5.281 2.125,5.469 0.219,0.188 10 false V 1.906,4.573 2.125,4.76 0.219,0.188 10 false P 1.042,4.635 1.479,4.823 0.438,0.188 10 false CA2H 1.042,5.208 1.479,5.396 0.438,0.188 10 false CA2L 1.49,4.635 1.802,4.854 0.313,0.219 10 false 35 1.49,5.208 1.802,5.427 0.313,0.219 10 false 34 0.104,5.479 0.542,5.667 0.438,0.188 10 false A58 0.396,5.49 2.042,6.177 1.646,0.688 10 false Brake Booster with Master Cylinder Assembly (Skid Control ECU) 2.958,6.177 3.177,6.365 0.219,0.188 10 false W 4.073,6.177 4.292,6.365 0.219,0.188 10 false B 2.76,6.729 3.198,6.917 0.438,0.188 10 false CANN 4.031,6.74 4.469,6.927 0.438,0.188 10 false CANP 3.042,6.521 3.26,6.708 0.219,0.188 10 false 4 4.042,6.51 4.26,6.698 0.219,0.188 10 false 12 3.375,7.385 4,7.594 0.625,0.208 10 false 120 Ω 4.583,7.094 5.021,7.281 0.438,0.188 10 false A57 4.875,7.104 5.24,7.344 0.365,0.24 10 false ECM 0.948,7.99 2.906,8.292 1.958,0.302 10 false : CAN Main Bus Line (CANH) 0.948,8.396 3.083,8.708 2.135,0.313 10 false : CAN Main Bus Line (CANL) 3.625,7.969 5.604,8.208 1.979,0.24 10 false : CAN Branch Line (CANH) 3.625,8.375 5.885,8.635 2.26,0.26 10 false : CAN Branch Line (CANL) 0.115,0.083 1.969,0.458 1.854,0.375 12 false Sub Bus 15: 3.792,3.552 4.104,3.771 0.313,0.219 10 false L101 3.802,4.156 4.188,4.385 0.385,0.229 10 false L132 2.563,5.083 2.875,5.302 0.313,0.219 10 false A67 3.073,5.604 3.385,5.823 0.313,0.219 10 false A67 3.813,5.604 4.125,5.823 0.313,0.219 10 false A67

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>DIAGNOSIS SYSTEM).



HINT:
·

Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.RECONFIRM DTC OUTPUT
a.

Reconfirm DTCs.


HINT:

If the hybrid vehicle control ECU outputs only DTC U0129, troubleshoot DTC U0129 and check the branch circuit of sub bus 15.


Result:
Result Proceed to
The hybrid vehicle control ECU outputs DTC U0129 and other DTCs.
(GTS display: Hybrid Control)
A
The hybrid vehicle control ECU outputs only DTC U0129.
(GTS display: Hybrid Control)
B



A

2.CHECK SUB BUS 15

B

GO TO DIAGNOSIS PROCEDURE INDICATED BY OUTPUT DTC

2.CHECK SUB BUS 15
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
U191053E04
2.635,1.698 2.323,1.052 2.323,1.052 2.083,1.052 false 2.698,1.708 2.823,1.021 2.823,1.021 2.896,1.021 false 2.427,1.906 2.177,2.438 2.177,2.438 2.042,2.438 false 2.469,1.906 2.625,2.438 2.625,2.438 2.74,2.438 false 2.583,0.583 2.875,0.844 0.292,0.26 10 false L6 0.125,0 0.479,0.354 0.354,0.354 10 false *a 1.656,2.354 2.177,2.594 0.521,0.24 10 false CA3P 2.781,2.354 3.302,2.594 0.521,0.24 10 false CA3N 2.958,0.938 3.354,1.177 0.396,0.24 10 false BATT 1.792,0.979 2.083,1.219 0.292,0.24 10 false E12

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Result
L6-31 (CA3P) - L6-30 (CA3N) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω Below 54 Ω:
Short circuit between bus lines
70 Ω or higher:
Open circuit in main bus lines
L6-31 (CA3P) - L6-4 (E12) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω:
CANH ground short
L6-30 (CA3N) - L6-4 (E12) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω:
CANL ground short
L6-31 (CA3P) - L6-3 (BATT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ:
CANH +B short
L6-30 (CA3N) - L6-3 (BATT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ:
CANL +B short


Text in Illustration
*a Component with harness connected
(Hybrid Vehicle Control ECU)

HINT:
·

When the value is as specified, clear and recheck for DTCs. When no DTCs are output, check for malfunctions such as damage or improper connection of the relevant connectors.

·

If DTCs are output although the bus circuit is normal and DTCs were cleared, replace the hybrid vehicle control ECU.




Result:
Result Proceed to
OK A
NG (Open circuit in CAN main bus lines) B
NG (Short circuit between bus lines) C
·

NG (Ground short)

·

NG (+B short)


D



A

B

3.CHECK FOR OPEN IN SUB BUS 15 LINES (HYBRID VEHICLE CONTROL ECU)

C

9.CHECK FOR SHORT IN SUB BUS 15 LINES (HYBRID VEHICLE CONTROL ECU)

D

16.CHECK FOR SHORT IN SUB BUS 15 LINE (HYBRID VEHICLE CONTROL ECU)
3.CHECK FOR OPEN IN SUB BUS 15 LINES (HYBRID VEHICLE CONTROL ECU)
a.
U154251E03
2.469,2.573 2.229,2.927 false 2.427,2.573 2.042,2.573 false 2.563,0.615 2.844,0.792 0.281,0.177 10 false L6 1.74,2.917 2.198,3.094 0.458,0.177 10 false CA3N 1.615,2.479 2,2.656 0.385,0.177 10 false CA3P 0.167,0.094 0.427,0.375 0.26,0.281 10 false *a

Disconnect the L6 hybrid vehicle control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L6-31 (CA3P) - L6-30 (CA3N) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Hybrid Vehicle Control ECU)



OK

NG

4.CHECK FOR OPEN IN SUB BUS 15 LINES (CAN NO. 5 JUNCTION CONNECTOR - CAN NO. 1 JUNCTION CONNECTOR)
4.CHECK FOR OPEN IN SUB BUS 15 LINES (CAN NO. 5 JUNCTION CONNECTOR - CAN NO. 1 JUNCTION CONNECTOR)
a.

Reconnect the L6 hybrid vehicle control ECU connector.


b.

Disconnect the L101 wire harness connector from the CAN No. 5 junction connector (instrument panel connector holder left side).


c.
U154800E03
1.781,1.74 1.781,0.969 1.781,0.969 1.938,0.969 false 1.448,1.75 1.448,0.969 1.448,0.969 1.104,0.969 false 0.125,0.094 0.385,0.313 0.26,0.219 10 false *a 0.396,1.656 0.813,1.865 0.417,0.208 10 false L101 0.542,0.885 1.208,1.208 0.667,0.323 10 false CANH*b 2,0.885 2.667,1.208 0.667,0.323 10 false CANL*b

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L101-2 (CANH) - L101-4 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to CAN No. 5 Junction Connector)
*b to CAN No. 1 Junction Connector



OK

5.CHECK FOR OPEN IN SUB BUS 15 LINES (CAN NO. 5 JUNCTION CONNECTOR - HYBRID VEHICLE CONTROL ECU)

NG

6.CHECK FOR OPEN IN SUB BUS 15 LINES (CAN NO. 1 JUNCTION CONNECTOR - CAN NO. 5 JUNCTION CONNECTOR)
5.CHECK FOR OPEN IN SUB BUS 15 LINES (CAN NO. 5 JUNCTION CONNECTOR - HYBRID VEHICLE CONTROL ECU)
a.

Reconnect the L101 wire harness connector to the CAN No. 5 junction connector (instrument panel connector holder left side).


b.

Disconnect the L102 wire harness connector from the CAN No. 5 junction connector (instrument panel connector holder right side).


c.
U154801E04
1.979,1.771 1.979,0.875 1.979,0.875 2.5,0.875 false 1.594,1.771 1.604,0.885 1.604,0.885 1.458,0.885 false 0.177,0.042 0.438,0.26 0.26,0.219 10 false *a 0.385,1.667 0.802,1.875 0.417,0.208 10 false L102 2.552,0.802 3.219,1.125 0.667,0.323 10 false CANH*b 0.885,0.792 1.552,1.115 0.667,0.323 10 false CANL*b

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L102-5 (CANH) - L102-3 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to CAN No. 5 Junction Connector)
*b to Hybrid Vehicle Control ECU



OK

REPLACE CAN NO. 5 JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (CAN NO. 5 JUNCTION CONNECTOR - HYBRID VEHICLE CONTROL ECU)

6.CHECK FOR OPEN IN SUB BUS 15 LINES (CAN NO. 1 JUNCTION CONNECTOR - CAN NO. 5 JUNCTION CONNECTOR)
a.

Reconnect the L101 wire harness connector to the CAN No. 5 junction connector (instrument panel connector holder left side).


b.

Disconnect the L132 wire harness connector from the CAN No. 1 junction connector (instrument panel wire side).


c.
U154802E02
1.615,2.083 1.615,2.688 1.615,2.688 1.271,2.688 false 1.615,1.74 1.615,0.958 1.615,0.958 1.271,0.958 false 0.146,0.094 0.406,0.313 0.26,0.219 10 false *a 0.406,1.656 0.823,1.865 0.417,0.208 10 false L132 0.75,0.885 1.417,1.208 0.667,0.323 10 false CANH*b 0.76,2.615 1.427,2.938 0.667,0.323 10 false CANL*b

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L132-3 (CANH) - L132-9 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to CAN No. 1 Junction Connector)
*b to CAN No. 5 Junction Connector



OK

7.CHECK FOR OPEN IN SUB BUS 15 LINES (CAN NO. 1 JUNCTION CONNECTOR - ECM)

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (CAN NO. 1 JUNCTION CONNECTOR - CAN NO. 5 JUNCTION CONNECTOR)

7.CHECK FOR OPEN IN SUB BUS 15 LINES (CAN NO. 1 JUNCTION CONNECTOR - ECM)
a.

Reconnect the L132 wire harness connector to the CAN No. 1 junction connector (instrument panel wire side).


b.

Disconnect the A67 wire harness connector from the CAN No. 1 junction connector (engine room main wire side).


c.
U154803E02
1.792,1.729 1.792,0.958 1.792,0.958 2.135,0.958 false 1.781,2.094 1.781,2.698 1.781,2.698 2.115,2.698 false 0.115,0.083 0.375,0.302 0.26,0.219 10 false *a 0.438,1.656 0.854,1.865 0.417,0.208 10 false A67 2.167,0.896 2.833,1.219 0.667,0.323 10 false CANH*b 2.146,2.635 2.813,2.958 0.667,0.323 10 false CANL*b

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A67-4 (CANH) - A67-10 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to CAN No. 1 Junction Connector)
*b to ECM



OK

REPLACE CAN NO. 1 JUNCTION CONNECTOR

NG

8.CHECK FOR OPEN IN SUB BUS 15 LINES (ECM)
8.CHECK FOR OPEN IN SUB BUS 15 LINES (ECM)
a.

Reconnect the A67 wire harness connector to the CAN No. 1 junction connector (engine room main wire side).


b.
U154225E02
1.698,1.656 1.365,2.573 false 1.469,1.135 1.698,1.594 false 0.156,0.125 0.927,0.448 0.771,0.323 10 false *a 0.271,1.781 0.552,1.948 0.281,0.167 10 false A57 1.115,0.938 1.646,1.083 0.531,0.146 10 false CANN 1.042,2.615 1.5,2.76 0.458,0.146 10 false CANP

Disconnect the A57 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A57-12 (CANP) - A57-4 (CANN) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to ECM)



OK

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (CAN NO. 1 JUNCTION CONNECTOR - ECM)

9.CHECK FOR SHORT IN SUB BUS 15 LINES (HYBRID VEHICLE CONTROL ECU)
a.
U154251E03
2.469,2.573 2.229,2.927 false 2.427,2.573 2.042,2.573 false 2.563,0.615 2.844,0.792 0.281,0.177 10 false L6 1.74,2.917 2.198,3.094 0.458,0.177 10 false CA3N 1.615,2.479 2,2.656 0.385,0.177 10 false CA3P 0.167,0.094 0.427,0.375 0.26,0.281 10 false *a

Disconnect the L6 hybrid vehicle control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L6-31 (CA3P) - L6-30 (CA3N) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Hybrid Vehicle Control ECU)



OK

NG

10.CHECK FOR SHORT IN SUB BUS 15 LINES (CAN NO. 5 JUNCTION CONNECTOR - HYBRID VEHICLE CONTROL ECU)
10.CHECK FOR SHORT IN SUB BUS 15 LINES (CAN NO. 5 JUNCTION CONNECTOR - HYBRID VEHICLE CONTROL ECU)
a.

Reconnect the L6 hybrid vehicle control ECU connector.


b.

Disconnect the L102 wire harness connector from the CAN No. 5 junction connector (instrument panel connector holder right side).


c.
U154801E04
1.979,1.771 1.979,0.875 1.979,0.875 2.5,0.875 false 1.594,1.771 1.604,0.885 1.604,0.885 1.458,0.885 false 0.177,0.042 0.438,0.26 0.26,0.219 10 false *a 0.385,1.667 0.802,1.875 0.417,0.208 10 false L102 2.552,0.802 3.219,1.125 0.667,0.323 10 false CANH*b 0.885,0.792 1.552,1.115 0.667,0.323 10 false CANL*b

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L102-5 (CANH) - L102-3 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to CAN No. 5 Junction Connector)
*b to Hybrid Vehicle Control ECU



OK

11.CHECK FOR SHORT IN SUB BUS 15 LINES (CAN NO. 5 JUNCTION CONNECTOR)

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (CAN NO. 5 JUNCTION CONNECTOR - HYBRID VEHICLE CONTROL ECU)

11.CHECK FOR SHORT IN SUB BUS 15 LINES (CAN NO. 5 JUNCTION CONNECTOR)
a.

Disconnect the L101 wire harness connector from the CAN No. 5 junction connector (instrument panel connector holder left side).


b.
U154800E03
1.781,1.74 1.781,0.969 1.781,0.969 1.938,0.969 false 1.448,1.75 1.448,0.969 1.448,0.969 1.104,0.969 false 0.125,0.094 0.385,0.313 0.26,0.219 10 false *a 0.396,1.656 0.813,1.865 0.417,0.208 10 false L101 0.542,0.885 1.208,1.208 0.667,0.323 10 false CANH*b 2,0.885 2.667,1.208 0.667,0.323 10 false CANL*b

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L101-2 (CANH) - L101-4 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to CAN No. 5 Junction Connector)
*b to CAN No. 1 Junction Connector



OK

REPLACE CAN NO. 5 JUNCTION CONNECTOR

NG

12.CHECK FOR SHORT IN SUB BUS 15 LINES (CAN NO. 1 JUNCTION CONNECTOR - CAN NO. 5 JUNCTION CONNECTOR)
12.CHECK FOR SHORT IN SUB BUS 15 LINES (CAN NO. 1 JUNCTION CONNECTOR - CAN NO. 5 JUNCTION CONNECTOR)
a.

Disconnect the L132 wire harness connector from the CAN No. 1 junction connector (instrument panel wire side).


b.
U154805E02
1.604,1.729 1.604,0.948 1.604,0.948 1.271,0.948 false 1.854,2.708 1.604,2.708 1.604,2.708 1.604,2.094 false 0.083,0.073 0.344,0.292 0.26,0.219 10 false *a 0.417,1.677 0.833,1.885 0.417,0.208 10 false L132 0.75,0.885 1.417,1.208 0.667,0.323 10 false CANH*b 1.906,2.635 2.573,2.958 0.667,0.323 10 false CANL*b

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L132-3 (CANH) - L132-9 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to CAN No. 1 Junction Connector)
*b to CAN No. 5 Junction Connector



OK

13.CHECK FOR SHORT IN SUB BUS 15 LINES (CAN NO. 1 JUNCTION CONNECTOR)

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (CAN NO. 1 JUNCTION CONNECTOR - CAN NO. 5 JUNCTION CONNECTOR)

13.CHECK FOR SHORT IN SUB BUS 15 LINES (CAN NO. 1 JUNCTION CONNECTOR)
a.

Disconnect the A67 wire harness connector from the CAN No. 1 junction connector (engine room main wire side).


b.
U154806E02
1.792,1.729 1.792,0.958 1.792,0.958 2.135,0.958 false 1.792,2.115 1.792,2.719 1.792,2.719 2.135,2.719 false 1.146,0.99 1.615,0.99 1.615,0.99 1.615,1.74 false 1.135,2.708 1.604,2.708 1.604,2.708 1.604,2.083 false 0.125,0.135 0.385,0.354 0.26,0.219 10 false *a 0.427,1.667 0.844,1.875 0.417,0.208 10 false A67 2.177,0.896 2.844,1.219 0.667,0.323 10 false CANH*c 2.167,2.635 2.833,2.958 0.667,0.323 10 false CANL*c 0.583,0.896 1.25,1.219 0.667,0.323 10 false CANH*b 0.594,2.625 1.26,2.948 0.667,0.323 10 false CANL*b

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A67-3 (CANH) - A67-9 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A67-4 (CANH) - A67-10 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to CAN No. 1 Junction Connector)
*b to Brake booster with master cylinder assembly (Skid control ECU)
*c to ECM


Result:
Result Proceed to
OK A
NG (ECM CAN main bus lines) B
NG (Brake booster with master cylinder assembly (skid control ECU) CAN branch lines) C



A

REPLACE CAN NO. 1 JUNCTION CONNECTOR

B

14.CHECK FOR SHORT IN SUB BUS 15 LINES (ECM)

C

15.CHECK FOR SHORT IN SUB BUS 15 LINES (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SKID CONTROL ECU)
14.CHECK FOR SHORT IN SUB BUS 15 LINES (ECM)
a.
U154225E02
1.698,1.656 1.365,2.573 false 1.469,1.135 1.698,1.594 false 0.156,0.125 0.927,0.448 0.771,0.323 10 false *a 0.271,1.781 0.552,1.948 0.281,0.167 10 false A57 1.115,0.938 1.646,1.083 0.531,0.146 10 false CANN 1.042,2.615 1.5,2.76 0.458,0.146 10 false CANP

Disconnect the A57 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A57-12 (CANP) - A57-4 (CANN) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to ECM)



OK

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (CAN NO. 1 JUNCTION CONNECTOR - ECM)

15.CHECK FOR SHORT IN SUB BUS 15 LINES (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SKID CONTROL ECU)
a.

Disconnect the A58 brake booster with master cylinder assembly (skid control ECU) connector.


b.
U154755E04
1.115,2.667 1.656,2.115 false 1.99,2.656 1.76,2.115 false 0.198,0.156 0.385,0.313 0.188,0.156 10 false *a 1.594,0.885 1.896,1.042 0.302,0.156 10 false A58 0.771,2.688 1.135,2.865 0.365,0.177 10 false CA2L 1.896,2.677 2.281,2.854 0.385,0.177 10 false CA2H

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A58-35 (CA2H) - A58-34 (CA2L) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Brake Booster with Master Cylinder Assembly (Skid Control ECU))


Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SKID CONTROL ECU)

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SKID CONTROL ECU)

C

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (CAN NO. 1 JUNCTION CONNECTOR - BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SKID CONTROL ECU))

16.CHECK FOR SHORT IN SUB BUS 15 LINE (HYBRID VEHICLE CONTROL ECU)
a.

Disconnect the L6 hybrid vehicle control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

U154951E04
3.792,2.156 4.219,2.365 false 3.969,2.75 4.281,2.354 false 4.188,4.208 4.188,4.531 false 3.156,3.115 3.458,3.115 3.458,3.115 3.458,3.604 false 1.229,0.25 1.458,0.448 0.229,0.198 10 false *a 1.229,3.156 1.458,3.354 0.229,0.198 10 false *1 3.427,2.052 3.854,2.229 0.427,0.177 10 false CA3P 3.583,2.667 4.01,2.844 0.427,0.177 10 false CA3N 2.917,3.042 3.177,3.198 0.26,0.156 10 false CG 4.063,4.531 4.375,4.688 0.313,0.156 10 false BAT 4.333,0.458 4.552,0.667 0.219,0.208 12 false L6 1.833,3.844 2.146,4.052 0.313,0.208 12 false L61

Standard Resistance:
Tester Connection Condition Specified Condition Result
L6-31 (CA3P) - L61-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Inspection for CANH ground short
L6-30 (CA3N) - L61-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Inspection for CANL ground short
L6-31 (CA3P) - L61-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Inspection for CANH +B short
L6-30 (CA3N) - L61-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Inspection for CANL +B short


Text in Illustration
*1 DLC3 - -
*a Rear view of wire harness connector
(to Hybrid Vehicle Control ECU)
- -

HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 15 inspection.

·

Find the necessary inspection from the Result column that matches the result in the Result column from the Check Sub Bus 15 inspection.





OK

NG

17.CHECK FOR SHORT IN SUB BUS 15 LINE (CAN NO. 5 JUNCTION CONNECTOR - HYBRID VEHICLE CONTROL ECU)
17.CHECK FOR SHORT IN SUB BUS 15 LINE (CAN NO. 5 JUNCTION CONNECTOR - HYBRID VEHICLE CONTROL ECU)
a.

Disconnect the L102 wire harness connector from the CAN No. 5 junction connector (instrument panel connector holder right side).


b.

Measure the resistance according to the value(s) in the table below.

U154832E02
3.448,3.635 3.448,3.167 3.448,3.167 3.198,3.167 false 4.198,4.177 4.198,4.51 false 3.427,1.458 3.427,0.646 3.427,0.646 3.177,0.646 false 3.979,0.604 3.729,0.604 3.729,0.604 3.729,1.448 false 1.938,2.813 2.177,3.031 0.24,0.219 10 false *1 2.125,3.885 2.573,4.125 0.448,0.24 10 false L61 2.396,1.438 2.854,1.75 0.458,0.313 10 false L102 1.927,0.177 2.167,0.396 0.24,0.219 10 false *a 4.031,0.531 4.677,0.76 0.646,0.229 10 false CANH*b 2.667,0.563 3.313,0.792 0.646,0.229 10 false CANL*b 4.073,4.521 4.479,4.792 0.406,0.271 10 false BAT 2.958,3.073 3.427,3.396 0.469,0.323 10 false CG

Standard Resistance:
Tester Connection Condition Specified Condition Result
L102-5 (CANH) - L61-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Inspection for CANH ground short
L102-3 (CANL) - L61-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Inspection for CANL ground short
L102-5 (CANH) - L61-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Inspection for CANH +B short
L102-3 (CANL) - L61-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Inspection for CANL +B short


Text in Illustration
*1 DLC3 - -
*a Front view of wire harness connector
(to CAN No. 5 Junction Connector)
*b to Hybrid vehicle control ECU

HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 15 inspection.

·

Find the necessary inspection from the Result column that matches the result in the Result column from the Check Sub Bus 15 inspection.





OK

18.CHECK FOR SHORT IN SUB BUS 15 LINE (CAN NO. 5 JUNCTION CONNECTOR)

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 5 JUNCTION CONNECTOR - HYBRID VEHICLE CONTROL ECU)

18.CHECK FOR SHORT IN SUB BUS 15 LINE (CAN NO. 5 JUNCTION CONNECTOR)
a.

Disconnect the L101 wire harness connector from the CAN No. 5 junction connector (instrument panel connector holder left side).


b.

Measure the resistance according to the value(s) in the table below.

U191054E03
3.448,3.625 3.448,3.156 3.448,3.156 3.198,3.156 false 4.177,4.188 4.177,4.521 false 3.281,1.469 3.281,0.656 3.281,0.656 3.031,0.656 false 3.573,1.469 3.573,0.656 3.573,0.656 3.823,0.656 false 1.958,2.875 2.24,3.156 0.281,0.281 10 false *1 2.125,3.865 2.573,4.104 0.448,0.24 10 false L61 2.385,1.438 2.844,1.75 0.458,0.313 10 false L101 1.969,0.146 2.26,0.427 0.292,0.281 10 false *a 2.479,0.573 3.125,0.802 0.646,0.229 10 false CANH*b 3.896,0.583 4.594,0.885 0.698,0.302 10 false CANL*b 4.052,4.573 4.521,4.802 0.469,0.229 10 false BAT 2.938,3.073 3.406,3.396 0.469,0.323 10 false CG

Standard Resistance:
Tester Connection Condition Specified Condition Result
L101-2 (CANH) - L61-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Inspection for CANH ground short
L101-4 (CANL) - L61-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Inspection for CANL ground short
L101-2 (CANH) - L61-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Inspection for CANH +B short
L101-4 (CANL) - L61-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Inspection for CANL +B short


Text in Illustration
*1 DLC3 - -
*a Front view of wire harness connector
(to CAN No. 5 Junction Connector)
*b to CAN No. 1 Junction Connector

HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 15 inspection.

·

Find the necessary inspection from the Result column that matches the result in the Result column from the Check Sub Bus 15 inspection.





OK

REPLACE CAN NO. 5 JUNCTION CONNECTOR

NG

19.CHECK FOR SHORT IN SUB BUS 15 LINE (CAN NO. 1 JUNCTION CONNECTOR - CAN NO. 5 JUNCTION CONNECTOR)
19.CHECK FOR SHORT IN SUB BUS 15 LINE (CAN NO. 1 JUNCTION CONNECTOR - CAN NO. 5 JUNCTION CONNECTOR)
a.

Disconnect the L132 wire harness connector from the CAN No. 1 junction connector (instrument panel wire side).


b.

Measure the resistance according to the value(s) in the table below.

U154834E02
3.458,3.635 3.458,3.167 3.458,3.167 3.208,3.167 false 4.167,4.177 4.167,4.51 false 3.438,1.479 3.438,0.667 3.438,0.667 3.188,0.667 false 3.427,1.75 3.427,2.292 3.427,2.292 3.188,2.292 false 2.01,2.833 2.25,3.052 0.24,0.219 10 false *1 2.115,3.865 2.563,4.104 0.448,0.24 10 false L61 2.385,1.448 2.844,1.76 0.458,0.313 10 false L132 2.042,0.146 2.281,0.365 0.24,0.219 10 false *a 2.656,0.594 3.302,0.823 0.646,0.229 10 false CANH*b 2.656,2.219 3.302,2.448 0.646,0.229 10 false CANL*b 4.052,4.542 4.458,4.813 0.406,0.271 10 false BAT 2.99,3.104 3.458,3.427 0.469,0.323 10 false CG

Standard Resistance:
Tester Connection Condition Specified Condition Result
L132-3 (CANH) - L61-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Inspection for CANH ground short
L132-9 (CANL) - L61-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Inspection for CANL ground short
L132-3 (CANH) - L61-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Inspection for CANH +B short
L132-9 (CANL) - L61-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Inspection for CANL +B short


HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 15 inspection.

·

Find the necessary inspection from the Result column that matches the result in the Result column from the Check Sub Bus 15 inspection.



Text in Illustration
*1 DLC3 - -
*a Front view of wire harness connector
(to CAN No. 1 Junction Connector)
*b to CAN No. 5 Junction Connector



OK

20.CHECK FOR SHORT IN SUB BUS 15 LINE (CAN NO. 1 JUNCTION CONNECTOR)

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 1 JUNCTION CONNECTOR - CAN NO. 5 JUNCTION CONNECTOR)

20.CHECK FOR SHORT IN SUB BUS 15 LINE (CAN NO. 1 JUNCTION CONNECTOR)
a.

Disconnect the A67 wire harness connector from the CAN No. 1 junction connector (engine room main wire side).


b.

Measure the resistance according to the value(s) in the table below.

U154835E02
3.458,3.625 3.458,3.156 3.458,3.156 3.208,3.156 false 4.167,4.188 4.167,4.521 false 3.438,1.458 3.438,0.646 3.438,0.646 3.188,0.646 false 3.563,1.479 3.563,0.667 3.563,0.667 3.813,0.667 false 3.125,2.5 3.417,2.5 3.417,2.5 3.417,1.781 false 3.719,2.479 3.573,2.479 3.573,2.479 3.573,1.792 false 2.01,2.875 2.25,3.094 0.24,0.219 10 false *1 2.104,3.865 2.552,4.104 0.448,0.24 10 false L61 2.406,1.427 2.865,1.74 0.458,0.313 10 false A67 2,0.135 2.24,0.354 0.24,0.219 10 false *a 2.656,0.583 3.302,0.813 0.646,0.229 10 false CANH*b 3.875,0.583 4.521,0.813 0.646,0.229 10 false CANH*c 2.573,2.417 3.219,2.646 0.646,0.229 10 false CANL*b 3.76,2.427 4.406,2.656 0.646,0.229 10 false CANL*c 4.042,4.51 4.448,4.781 0.406,0.271 10 false BAT 3,3.094 3.469,3.417 0.469,0.323 10 false CG

Standard Resistance:
Tester Connection Condition Specified Condition Result Connected to
A67-3 (CANH) - L61-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Inspection for CANH ground short Brake booster with master cylinder assembly (skid control ECU)
A67-9 (CANL) - L61-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Inspection for CANL ground short
A67-4 (CANH) - L61-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Inspection for CANH ground short ECM
A67-10 (CANL) - L61-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Inspection for CANL ground short
A67-3 (CANH) - L61-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Inspection for CANH +B short Brake booster with master cylinder assembly (skid control ECU)
A67-9 (CANL) - L61-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Inspection for CANL +B short
A67-4 (CANH) - L61-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Inspection for CANH +B short ECM
A67-10 (CANL) - L61-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Inspection for CANL +B short


Text in Illustration
*1 DLC3 - -
*a Front view of wire harness connector
(to CAN No. 1 Junction Connector)
*b to Brake booster with master cylinder assembly (Skid control ECU)
*c to ECM - -

HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 15 inspection.

·

Find the necessary inspection from the Result column that matches the result in the Result column from the Check Sub Bus 15 inspection.





OK

REPLACE CAN NO. 1 JUNCTION CONNECTOR

NG

21.CHECK SUB BUS 15 LINE (ECU OR SENSOR)
21.CHECK SUB BUS 15 LINE (ECU OR SENSOR)
a.

Reconnect all wire harness connectors.


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the bus line shorted to +B or shorted to GND is connected.


c.
U191053E06
2.625,1.698 2.313,1.052 2.313,1.052 2.073,1.052 false 2.698,1.698 2.823,1.01 2.823,1.01 2.896,1.01 false 2.417,1.906 2.167,2.438 2.167,2.438 2.031,2.438 false 2.469,1.906 2.625,2.438 2.625,2.438 2.74,2.438 false 2.573,0.583 2.865,0.844 0.292,0.26 10 false L6 0.125,0 0.479,0.354 0.354,0.354 10 false *a 1.625,2.354 2.146,2.594 0.521,0.24 10 false CA3P 2.802,2.354 3.323,2.594 0.521,0.24 10 false CA3N 2.958,0.938 3.344,1.271 0.385,0.333 10 false BATT 1.781,0.969 2.156,1.26 0.375,0.292 10 false E12

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Result
L6-31 (CA3P) - L6-4 (E12) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω:
CANH ground short
L6-30 (CA3N) - L6-4 (E12) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω:
CANL ground short
L6-31 (CA3P) - L6-3 (BATT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ:
CANH +B short
L6-30 (CA3N) - L6-3 (BATT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ:
CANL +B short


Text in Illustration
*a Component with harness connected
(Hybrid Vehicle Control ECU)

HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 15 inspection.

·

Find the necessary inspection from the Result column that matches the result in the Result column from the Check Sub Bus 15 inspection.





OK

REPLACE CORRESPONDING ECU OR SENSOR

NG

REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR