Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU) › 2012.03–2014.11
RM2070E _57 Power Source / Network _061936 NETWORKING _0301754 CAN COMMUNICATION SYSTEM(w/o Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(w/o Central Gateway ECU)  Check CAN Bus Lines for Short Circuit (LHD Models)  


DESCRIPTION

There may be a short circuit between the V bus main lines and/or CAN branch lines when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 54 Ω.

Symptom Trouble Area
Resistance between terminals 6 (CANH) and 14 (CANL) of DLC3 is below 54 Ω.
·

Short in CAN main bus line

·

Short in CAN branch line

·

Power management control ECU

·

ECM

·

Main body ECU (Multiplex network body ECU)

·

Meter circuit plate

·

Brake booster with master cylinder assembly (Skid control ECU)

·

Spiral cable with sensor sub-assembly (Steering angle sensor)

·

Yaw rate sensor

·

Power steering ECU assembly

·

Airbag ECU assembly

·

Transmission control ECU assembly

·

Certification ECU (Smart key ECU assembly)

·

Navigation ECU sub-assembly*1

·

Radio and display receiver assembly*2

·

CAN No. 1 junction connector

·

CAN No. 2 junction connector

·

CAN No. 3 junction connector



*1: for Navigation receiver type

*2: for Radio and display type

WIRING DIAGRAM

C240427E09
3.969,7.958 5.698,8.146 1.729,0.188 10 false : CAN Branch Line (CANH) 3.958,8.375 5.688,8.563 1.729,0.188 10 false : CAN Branch Line (CANL) 0.833,7.979 2.75,8.167 1.917,0.188 10 false : CAN Main Bus Line (CANH) 0.833,8.385 2.75,8.573 1.917,0.188 10 false : CAN Main Bus Line (CANL) 3.469,0.354 3.885,0.542 0.417,0.188 10 false 120 Ω 2.823,0.948 3.229,1.115 0.406,0.167 10 false CANL 1.052,3.469 1.458,3.635 0.406,0.167 10 false CANL 1.844,0.573 2.135,0.74 0.292,0.167 10 false A57 4.146,1.49 4.281,1.656 0.135,0.167 10 false P 5.125,2.615 5.26,2.781 0.135,0.167 10 false L 2.188,3.5 2.344,3.667 0.156,0.167 10 false R 2.156,5.698 2.313,5.865 0.156,0.167 10 false B 2.156,6.385 2.313,6.552 0.156,0.167 10 false W 5.063,6.969 5.25,7.229 0.188,0.26 10 false W 3.021,4.469 3.177,4.635 0.156,0.167 10 false W 5.135,5.677 5.292,5.844 0.156,0.167 10 false W 4.156,4.469 4.313,4.635 0.156,0.167 10 false B 5.156,4.927 5.313,5.094 0.156,0.167 10 false B 3.063,1.49 3.229,1.656 0.167,0.167 10 false V 3.135,1.823 3.427,1.99 0.292,0.167 10 false A67 0.177,3.771 0.469,3.938 0.292,0.167 10 false L7 2.615,3.01 3,3.177 0.385,0.167 10 false L132 2.615,3.375 3.01,3.542 0.396,0.167 10 false L132 3.104,4.208 3.51,4.375 0.406,0.167 10 false L132 3.906,4.823 4.177,4.99 0.271,0.167 10 false L94 4.417,5.125 4.74,5.292 0.323,0.167 10 false L95 4.417,5.49 4.677,5.656 0.26,0.167 10 false L95 4.417,6.396 4.719,6.563 0.302,0.167 10 false L95 4.427,6.76 4.76,6.927 0.333,0.167 10 false L95 4.802,7.24 5.083,7.406 0.281,0.167 10 false L54 3.146,4.823 3.417,4.99 0.271,0.167 10 false L94 2.646,5.865 2.906,6.031 0.26,0.167 10 false L95 2.646,6.219 2.906,6.385 0.26,0.167 10 false L95 3.865,4.208 4.26,4.375 0.396,0.167 10 false L132 3.917,1.823 4.208,1.99 0.292,0.167 10 false A67 4.427,2.073 4.719,2.24 0.292,0.167 10 false A67 4.427,2.438 4.719,2.604 0.292,0.167 10 false A67 2.167,0.573 2.573,0.74 0.406,0.167 10 false ECM 4.115,0.969 4.552,1.135 0.438,0.167 10 false CANH 6.094,5.427 6.5,5.594 0.406,0.167 10 false CANL 5.938,5.083 6.375,5.25 0.438,0.167 10 false CANH 1.042,2.885 1.479,3.052 0.438,0.167 10 false CANH 1.073,6.354 1.479,6.521 0.406,0.167 10 false CANL 1.042,5.729 1.479,5.896 0.438,0.167 10 false CANH 5.885,6.896 6.292,7.063 0.406,0.167 10 false CANL 5.854,6.26 6.292,6.427 0.438,0.167 10 false CANH 5.917,1.917 6.354,2.083 0.438,0.167 10 false CA1H 5.896,2.563 6.333,2.729 0.438,0.167 10 false CA1L 4.083,1.229 4.292,1.396 0.208,0.167 10 false 13 2.865,4.208 3.073,4.375 0.208,0.167 10 false 12 2.729,6.427 2.833,6.594 0.104,0.167 10 false 6 2.719,5.667 2.833,5.833 0.115,0.167 10 false 5 5.625,5.583 5.833,5.75 0.208,0.167 10 false 14 5.604,1.958 5.813,2.125 0.208,0.167 10 false 37 5.604,2.573 5.813,2.74 0.208,0.167 10 false 38 1.563,2.896 1.771,3.063 0.208,0.167 10 false 14 4.458,4.896 4.635,5.063 0.177,0.167 10 false 14 2.74,2.802 2.948,2.969 0.208,0.167 10 false 5 2.698,3.573 2.906,3.74 0.208,0.167 10 false 11 1.552,3.469 1.76,3.635 0.208,0.167 10 false 13 4.51,6.969 4.719,7.135 0.208,0.167 10 false 3 4.51,6.177 4.719,6.344 0.208,0.167 10 false 2 5.073,1.896 5.281,2.063 0.208,0.167 10 false LG 2.146,2.844 2.375,3.01 0.229,0.167 10 false SB 2.927,1.781 3.052,1.948 0.125,0.167 10 false 7 3.125,1.229 3.24,1.396 0.115,0.167 10 false 5 4.313,4.198 4.427,4.365 0.115,0.167 10 false 6 4.479,5.688 4.656,5.854 0.177,0.167 10 false 15 5.667,4.99 5.781,5.156 0.115,0.167 10 false 6 4.271,4.792 4.385,4.958 0.115,0.167 10 false 5 2.948,4.792 3.063,4.958 0.115,0.167 10 false 4 4.302,1.781 4.417,1.948 0.115,0.167 10 false 1 4.521,1.854 4.635,2.021 0.115,0.167 10 false 2 1.604,6.333 1.719,6.5 0.115,0.167 10 false 2 1.604,5.729 1.719,5.896 0.115,0.167 10 false 3 5.635,6.875 5.75,7.042 0.115,0.167 10 false 7 5.635,6.292 5.75,6.458 0.115,0.167 10 false 1 4.521,2.646 4.708,2.813 0.188,0.167 10 false 8 5.25,0.438 6.458,0.625 1.208,0.188 10 false x: Suspected Area 5.083,2.844 5.375,2.979 0.292,0.135 10 false A58 5.406,2.844 7.125,3.396 1.719,0.552 10 false Brake Booster with Master Cylinder Assembly (Skid Control ECU) 6.063,5.688 6.375,5.875 0.313,0.188 10 false L61 6.365,5.688 6.76,5.875 0.396,0.188 10 false DLC3 0.396,3.771 2.135,4.313 1.74,0.542 10 false Main Body ECU (Multiplex Network Body ECU) 0.906,2.115 2.896,2.615 1.99,0.5 10 false CAN No. 1 Junction Connector 0.896,5.198 2.885,5.385 1.99,0.188 10 false CAN No. 2 Junction Connector 0.25,6.698 0.542,6.854 0.292,0.156 10 false L12 0.573,6.698 1.729,6.906 1.156,0.208 10 false Yaw Rate Sensor 5.125,7.24 7.073,7.427 1.948,0.188 10 false Power Steering ECU Assembly 5.073,6.281 5.229,6.448 0.156,0.167 10 false R

C242542E14
0.792,8.01 2.708,8.198 1.917,0.188 10 false : CAN Main Bus Line (CANH) 3.979,8.031 5.698,8.219 1.719,0.188 10 false : CAN Branch Line (CANH) 3.979,8.448 5.698,8.635 1.719,0.188 10 false : CAN Branch Line (CANL) 0.792,8.406 2.708,8.594 1.917,0.188 10 false : CAN Main Bus Line (CANL) 0.813,0.458 2.802,0.646 1.99,0.188 10 false CAN No. 2 Junction Connector 0.094,6.708 2.313,6.99 2.219,0.281 10 false *1: for Navigation Receiver Type 4.438,4.354 6.427,4.542 1.99,0.188 10 false CAN No. 3 Junction Connector 0.479,3.615 1.927,3.865 1.448,0.25 10 false Airbag ECU Assembly 5.833,1.01 6.24,1.177 0.406,0.167 10 false CANL 5.823,0.365 6.26,0.531 0.438,0.167 10 false CANH 5.813,2.635 6.219,2.802 0.406,0.167 10 false CANL 5.802,2 6.24,2.167 0.438,0.167 10 false CANH 5.813,5.385 6.219,5.552 0.406,0.167 10 false CA1L 5.802,4.76 6.24,4.927 0.438,0.167 10 false CA1H 2.781,6.76 3.188,6.927 0.406,0.167 10 false CANL 4.083,6.76 4.521,6.927 0.438,0.167 10 false CANH 1.042,1.698 1.448,1.865 0.406,0.167 10 false CANL 1.031,1.115 1.469,1.281 0.438,0.167 10 false CANH 1.021,3.292 1.427,3.458 0.406,0.167 10 false CANL 1.01,2.667 1.448,2.833 0.438,0.167 10 false CANH 4.396,0.521 4.677,0.688 0.281,0.167 10 false L94 4.396,0.885 4.677,1.052 0.281,0.167 10 false L94 4.396,2.167 4.656,2.333 0.26,0.167 10 false L95 4.396,2.531 4.646,2.698 0.25,0.167 10 false L95 3.125,3.49 3.396,3.656 0.271,0.167 10 false L94 3.875,3.49 4.146,3.656 0.271,0.167 10 false L94 3.073,4.188 3.396,4.354 0.323,0.167 10 false L133 3.094,5.844 3.448,6.01 0.354,0.167 10 false L133 3.844,5.844 4.219,6.01 0.375,0.167 10 false L133 3.844,4.188 4.25,4.354 0.406,0.167 10 false L133 2.594,1.24 2.844,1.406 0.25,0.167 10 false L94 2.594,1.604 2.854,1.771 0.26,0.167 10 false L94 2.604,2.833 2.865,3 0.26,0.167 10 false L95 2.604,3.188 2.865,3.354 0.26,0.167 10 false L95 1.542,1.125 1.656,1.292 0.115,0.167 10 false 9 2.688,1.802 2.802,1.969 0.115,0.167 10 false 7 2.667,1.01 2.781,1.177 0.115,0.167 10 false 8 2.063,1.052 2.177,1.219 0.115,0.167 10 false B 2.063,1.781 2.229,1.948 0.167,0.167 10 false W 1.5,1.708 1.677,1.875 0.177,0.167 10 false 10 1.563,2.677 1.75,2.844 0.188,0.167 10 false 13 2.677,3.385 2.792,3.552 0.115,0.167 10 false 9 4.24,3.49 4.354,3.656 0.115,0.167 10 false 2 2.906,3.49 3.021,3.656 0.115,0.167 10 false 1 2.677,2.604 2.792,2.771 0.115,0.167 10 false 8 2.042,2.635 2.156,2.802 0.115,0.167 10 false B 2.042,3.365 2.198,3.531 0.156,0.167 10 false W 1.563,3.292 1.75,3.458 0.188,0.167 10 false 22 0.083,2.01 0.344,2.177 0.26,0.167 10 false L62 5.615,0.396 5.729,0.563 0.115,0.167 10 false 4 4.417,1.083 4.604,1.25 0.188,0.167 10 false 10 4.427,2.729 4.615,2.896 0.188,0.167 10 false 12 4.427,1.927 4.615,2.094 0.188,0.167 10 false 11 2.854,4.167 3.042,4.333 0.188,0.167 10 false 11 2.844,5.844 3.031,6.01 0.188,0.167 10 false 12 4.24,4.167 4.427,4.333 0.188,0.167 10 false 5 4.24,5.833 4.427,6 0.188,0.167 10 false 6 4.427,0.292 4.615,0.458 0.188,0.167 10 false 11 5,0.375 5.146,0.542 0.146,0.167 10 false B 5,1.063 5.188,1.229 0.188,0.167 10 false W 5,1.99 5.146,2.156 0.146,0.167 10 false B 5,2.698 5.146,2.865 0.146,0.167 10 false W 4.083,6.26 4.302,6.427 0.219,0.167 10 false SB 3,6.26 3.146,6.427 0.146,0.167 10 false G 5.615,1 5.74,1.167 0.125,0.167 10 false 3 5.573,2.042 5.76,2.208 0.188,0.167 10 false 9 5.552,2.646 5.74,2.813 0.188,0.167 10 false 10 5.552,4.792 5.74,4.958 0.188,0.167 10 false 16 4.479,4.698 4.667,4.865 0.188,0.167 10 false 1 4.479,5.469 4.667,5.635 0.188,0.167 10 false 7 4.938,5.458 5.156,5.625 0.219,0.167 10 false BR 4.969,4.771 5.104,4.938 0.135,0.167 10 false Y 5.563,5.396 5.75,5.563 0.188,0.167 10 false 15 4.063,6.5 4.25,6.667 0.188,0.167 10 false 19 3,6.5 3.188,6.667 0.188,0.167 10 false 20 0.177,3.615 0.458,3.781 0.281,0.167 10 false L16 4.375,4.917 4.656,5.083 0.281,0.167 10 false A68 4.385,5.281 4.667,5.448 0.281,0.167 10 false A68 5.271,5.667 5.552,5.833 0.281,0.167 10 false A24 4.719,2.917 5,3.083 0.281,0.167 10 false L38 0.125,6.323 1.333,6.51 1.208,0.188 10 false x: Suspected Area 3.448,7.51 3.958,7.698 0.51,0.188 10 false 120 Ω 0.375,2.01 1.896,2.427 1.521,0.417 10 false Certification ECU (Smart Key ECU Assembly) 5.031,2.917 7.135,3.188 2.104,0.271 10 false Navigation ECU Sub-assembly*1 4.677,1.281 4.969,1.458 0.292,0.177 10 false L51 5,1.281 7.135,1.844 2.135,0.563 10 false Spiral Cable with Sensor Sub-assembly (Steering Angle Sensor) 5.594,5.667 6.917,6.281 1.323,0.615 10 false Transmission Control ECU Assembly 4.771,7.208 5.042,7.406 0.271,0.198 10 false L27 5.094,7.208 6.302,7.406 1.208,0.198 10 false Meter Circuit Plate 4.125,3.823 4.375,3.99 0.25,0.167 10 false GR 2.969,3.823 3.115,3.99 0.146,0.167 10 false W 0.323,5.417 1.667,5.927 1.344,0.51 10 false Power Management Control ECU 1.031,5.135 1.438,5.302 0.406,0.167 10 false CA1L 1.021,4.51 1.458,4.677 0.438,0.167 10 false CA1H 2.021,5.208 2.167,5.375 0.146,0.167 10 false P 2.021,4.458 2.167,4.625 0.146,0.167 10 false V 2.552,4.656 2.927,4.823 0.375,0.167 10 false L133 2.552,5.021 2.917,5.188 0.365,0.167 10 false L133 0.083,5.417 0.323,5.583 0.24,0.167 10 false L6 2.635,4.438 2.823,4.604 0.188,0.167 10 false 4 2.635,5.208 2.823,5.375 0.188,0.167 10 false 10 1.51,4.552 1.698,4.719 0.188,0.167 10 false 25 1.51,5.135 1.698,5.302 0.188,0.167 10 false 24 5.031,3.302 6.99,3.75 1.958,0.448 10 false Radio and Display Receiver Assembly*2 0.094,7.104 1.625,7.573 1.531,0.469 10 false *2: for Radio and Display Receiver Type 4.719,3.302 5,3.469 0.281,0.167 10 false L35

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the power switch on (IG), turn the cruise control system on using the cruise control switch (ON/OFF switch), wait at least 60 seconds, and then drive the vehicle at a speed of 50 km/h (31 mph) or more for at least 1.72 seconds.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>DIAGNOSIS SYSTEM).



HINT:
·

Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR SHORT IN CAN BUS LINES (ECM)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
U154712E01
1.603,0.657 1.906,0.813 0.303,0.156 10 A57 0.178,0.182 0.532,0.455 0.353,0.273 10 *a 2.581,1.039 3.042,1.275 0.461,0.236 10 CANH 2.473,0.795 2.950,1.045 0.477,0.250 10 CANL 1.93,1.677 2.184,0.892 2.184,0.892 2.43,0.892 false 1.958,1.789 2.242,1.117 2.242,1.117 2.533,1.117 false

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A57-13 (CANH) - A57-5 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to ECM)



OK

NG

2.CHECK FOR SHORT IN CAN BUS LINES (METER CIRCUIT PLATE)
2.CHECK FOR SHORT IN CAN BUS LINES (METER CIRCUIT PLATE)
a.

Reconnect the ECM connector.


b.
U154716E02
2.844,2.469 3.052,2.927 false 2.719,2.469 2.333,2.927 false 0.198,0.156 0.438,0.5 0.24,0.344 10 false *a 2.802,2.948 3.26,3.115 0.458,0.167 10 false CANL 2.125,2.958 2.583,3.125 0.458,0.167 10 false CANH 1.677,0.74 1.99,0.906 0.313,0.167 10 false L27

Disconnect the meter circuit plate connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L27-19 (CANH) - L27-20 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to Meter Circuit Plate)



OK

NG

3.CHECK FOR SHORT IN CAN BUS LINES (CAN NO. 2 J/C)
3.CHECK FOR SHORT IN CAN BUS LINES (CAN NO. 2 J/C)
a.

Reconnect the meter circuit plate connector.


b.
U154777E02
1,1.104 1.094,1.104 1.094,1.104 1.552,1.646 false 2.5,1.083 1.938,1.083 1.938,1.083 1.698,1.646 false 1,1.646 1.094,1.646 1.094,1.646 1.552,1.854 false 2.531,1.635 1.969,1.635 1.969,1.635 1.719,1.875 false 2.552,2.26 2.396,2.26 2.396,2.26 1.729,2.052 false 1,2.292 1.094,2.292 1.094,2.292 1.563,2.063 false 2.531,2.688 2.375,2.688 2.375,2.688 1.708,2.26 false 1,2.719 1.094,2.719 1.094,2.719 1.563,2.271 false 0.073,0.073 0.625,0.438 0.552,0.365 10 false *a 2.563,0.99 3.146,1.219 0.583,0.229 10 false CANH*b 0.458,1 1.052,1.25 0.594,0.25 10 false CANL*b 2.604,1.542 3.156,1.813 0.552,0.271 10 false CANH*c 0.458,1.552 1.042,1.802 0.583,0.25 10 false CANL*c 1.625,0.583 1.885,0.76 0.26,0.177 10 false L94 0.438,2.188 1.052,2.458 0.615,0.271 10 false CANL*d 2.604,2.156 3.177,2.333 0.573,0.177 10 false CANH*d 0.438,2.615 1.052,2.885 0.615,0.271 10 false CANL*e 2.594,2.594 3.208,2.875 0.615,0.281 10 false CANH*e

Disconnect the wire harness connector from the CAN No. 2 junction connector (instrument panel connector holder left side).


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
L94-2 (CANH) - L94-1 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω CAN No. 3 junction connector
L94-5 (CANH) - L94-4 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω CAN No. 1 junction connector
L94-8 (CANH) - L94-7 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Certification ECU (Smart key ECU assembly)
L94-11 (CANH) - L94-10 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Spiral cable with sensor sub-assembly (Steering angle sensor)


Text in Illustration
*a Front view of wire harness connector
(to CAN No. 2 Junction Connector)
*b to CAN No. 3 Junction Connector
*c to CAN No. 1 Junction Connector
*d to Certification ECU (Smart Key ECU Assembly)
*e to Spiral Cable with Sensor Sub-assembly (Steering Angle Sensor)

Result:
Result Proceed to
OK A
NG (CAN No. 1 junction connector main line) B
NG (CAN No. 3 junction connector main line) C
NG (ECU or sensor branch line) D




A

4.CHECK FOR SHORT IN CAN BUS LINES (CAN NO. 2 J/C)

B

5.CHECK FOR SHORT IN CAN BUS LINES (CAN NO. 1 J/C)

C

7.CHECK FOR SHORT IN CAN BUS LINES (CAN NO. 3 J/C)

D

9.CHECK FOR SHORT IN CONNECTED COMPONENT (ECU, SENSOR)
4.CHECK FOR SHORT IN CAN BUS LINES (CAN NO. 2 J/C)
a.

Disconnect the wire harness connector from the CAN No. 2 junction connector (instrument panel connector holder right side).


b.
U154778E03
1,1.104 1.229,1.104 1.229,1.104 1.698,1.656 false 2.5,1.083 2.073,1.083 2.073,1.083 1.833,1.646 false 1.01,1.646 1.24,1.646 1.24,1.646 1.698,1.854 false 2.531,1.615 2.104,1.615 2.104,1.615 1.854,1.854 false 2.552,2.271 2.396,2.271 2.396,2.271 1.875,2.063 false 1,2.292 1.229,2.292 1.229,2.292 1.698,2.063 false 2.552,2.635 2.396,2.635 2.396,2.635 1.875,2.271 false 1.01,2.625 1.24,2.625 1.24,2.625 1.708,2.25 false 2.531,2.99 2.375,2.99 2.375,2.99 1.854,2.448 false 1.01,3.052 1.24,3.052 1.24,3.052 1.719,2.448 false 0.156,0.104 0.594,0.417 0.438,0.313 10 false *a 0.427,1.01 1.052,1.24 0.625,0.229 10 false CANH*b 2.542,1 3.135,1.25 0.594,0.25 10 false CANL*b 0.438,1.542 1.01,1.813 0.573,0.271 10 false CANH*c 2.594,1.531 3.177,1.781 0.583,0.25 10 false CANL*c 1.625,0.594 1.885,0.771 0.26,0.177 10 false L95 2.604,2.167 3.219,2.438 0.615,0.271 10 false CANL*d 0.438,2.198 1.021,2.375 0.583,0.177 10 false CANH*d 2.604,2.542 3.219,2.813 0.615,0.271 10 false CANL*e 0.438,2.531 1,2.813 0.563,0.281 10 false CANH*e 2.594,2.896 3.208,3.167 0.615,0.271 10 false CANL*f 0.469,2.958 1.063,3.177 0.594,0.219 10 false CANH*f

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
L95-2 (CANH) - L95-3 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Power steering ECU assembly
L95-5 (CANH) - L95-6 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Yaw rate sensor
L95-8 (CANH) - L95-9 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Airbag ECU assembly
L95-11 (CANH) - L95-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
·

Navigation ECU sub-assembly*1

·

Radio and display receiver assembly*2


L95-14 (CANH) - L95-15 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher DLC3


*1: for Navigation receiver type

*2: for Radio and display type

Text in Illustration
*a Front view of wire harness connector
(to CAN No. 2 Junction Connector)
*b to Power Steering ECU Assembly
*c to Yaw Rate Sensor
*d to Airbag ECU Assembly
*e
·

to Navigation ECU Sub-assembly*1

·

to Radio and Display Receiver Assembly*2


*f to DLC3

*1: for Navigation receiver type

*2: for Radio and display type


Result:
Result Proceed to
OK A
NG (ECU or sensor branch line) B
NG (DLC3 branch line) C



A

REPLACE CAN NO. 2 JUNCTION CONNECTOR

B

9.CHECK FOR SHORT IN CONNECTED COMPONENT (ECU, SENSOR)

C

REPAIR OR REPLACE CAN BRANCH LINE CONNECTED TO DLC3

5.CHECK FOR SHORT IN CAN BUS LINES (CAN NO. 1 J/C)
a.
U154810E03
2.115,1.74 2.115,0.969 2.115,0.969 2.458,0.969 false 2.135,2.073 2.135,2.552 2.135,2.552 2.5,2.552 false 1.01,2.563 1.958,2.563 1.958,2.563 1.958,2.073 false 0.844,0.979 1.969,0.979 1.969,0.979 1.969,1.74 false 0.115,0 0.375,0.219 0.26,0.219 10 false *a 1.542,0.583 1.896,0.792 0.354,0.208 10 false L132 2.521,0.885 3.188,1.208 0.667,0.323 10 false CANH*c 0.24,0.875 0.906,1.198 0.667,0.323 10 false CANH*b 2.573,2.458 3.24,2.781 0.667,0.323 10 false CANL*c 0.417,2.458 1.083,2.781 0.667,0.323 10 false CANL*b

Disconnect the wire harness connector from the CAN No. 1 junction connector (instrument panel wire side).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
L132-5 (CANH) - L132-11 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Main body ECU (Multiplex network body ECU)
L132-6 (CANH) - L132-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher CAN No. 2 junction connector


Text in Illustration
*a Front view of wire harness connector
(to CAN No. 1 Junction Connector)
*b to Main Body ECU (Multiplex Network Body ECU)
*c to CAN No. 2 Junction Connector


Result:
Result Proceed to
OK A
NG (CAN No. 2 junction connector main line) B
NG (ECU or sensor branch line) C



A

6.CHECK FOR SHORT IN CAN BUS LINES (CAN NO. 1 J/C)

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 2 J/C - CAN NO. 1 J/C)

C

9.CHECK FOR SHORT IN CONNECTED COMPONENT (ECU, SENSOR)
6.CHECK FOR SHORT IN CAN BUS LINES (CAN NO. 1 J/C)
a.

Disconnect the wire harness connector from the CAN No. 1 junction connector (engine room main wire side).


b.

Measure the resistance according to the value(s) in the table below.


U154811E02
1.417,1.74 1.417,0.969 1.417,0.969 2.458,0.969 false 1.406,2.063 1.406,2.542 1.406,2.542 2.469,2.542 false 1,2.552 1.25,2.552 1.25,2.552 1.25,2.063 false 0.823,0.99 1.25,0.99 1.25,0.99 1.25,1.75 false 0.167,0.135 0.458,0.406 0.292,0.271 10 false *a 1.583,0.604 1.917,0.875 0.333,0.271 10 false A67 2.51,0.875 3.177,1.198 0.667,0.323 10 false CANH*c 0.24,0.896 0.906,1.219 0.667,0.323 10 false CANH*b 2.531,2.448 3.198,2.771 0.667,0.323 10 false CANL*c 0.417,2.448 1.083,2.771 0.667,0.323 10 false CANL*b

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
A67-1 (CANH) - A67-7 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω ECM
A67-2 (CANH) - A67-8 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Brake booster with master cylinder assembly (Skid control ECU)


Text in Illustration
*a Front view of wire harness connector
(to CAN No. 1 Junction Connector)
*b to ECM
*c to Brake Booster with Master Cylinder Assembly (Skid Control ECU)

Result:
Result Proceed to
OK A
NG (ECM main line) B
NG (ECU or sensor branch line) C



A

REPLACE CAN NO. 1 JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 1 J/C - ECM)

C

9.CHECK FOR SHORT IN CONNECTED COMPONENT (ECU, SENSOR)
7.CHECK FOR SHORT IN CAN BUS LINES (CAN NO. 3 J/C)
a.

Disconnect the wire harness connector from the CAN No. 3 junction connector (instrument panel wire side).


b.
U154812E02
1.781,2.094 1.781,2.552 1.781,2.552 1.438,2.552 false 1.948,2.083 1.948,3.042 1.948,3.042 1.604,3.042 false 1.771,1.74 1.771,0.958 1.771,0.958 1.427,0.958 false 1.958,1.74 1.958,0.563 1.958,0.563 1.615,0.563 false 2.333,0.792 2.125,0.792 2.125,0.792 2.125,1.719 false 2.406,2.677 2.135,2.677 2.135,2.677 2.135,2.094 false 0.135,0.104 0.396,0.323 0.26,0.219 10 false *a 0.406,1.656 0.823,1.865 0.417,0.208 10 false L133 0.865,0.865 1.531,1.188 0.667,0.323 10 false CANH*b 0.896,2.458 1.563,2.781 0.667,0.323 10 false CANL*b 1.042,2.927 1.708,3.25 0.667,0.323 10 false CANL*c 2.458,2.583 3.125,2.906 0.667,0.323 10 false CANL*d 1.042,0.458 1.708,0.781 0.667,0.323 10 false CANH*c 2.396,0.708 3.063,1.031 0.667,0.323 10 false CANH*d

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
L133-4 (CANH) -L133-10 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Power management control ECU
L133-5 (CANH) - L133-11 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher CAN No. 2 junction connector
L133-6 (CANH) - L133-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω Meter circuit plate


Text in Illustration
*a Front view of wire harness connector
(to CAN No. 3 Junction Connector)
*b to Power Management Control ECU
*c to CAN No. 2 Junction Connector
*d to Meter Circuit Plate


Result:
Result Proceed to
OK A
NG (CAN No. 2 junction connector main line) B
NG (Meter circuit plate main line) C
NG (ECU or sensor branch line) D



A

8.CHECK FOR SHORT IN CAN BUS LINES (CAN NO. 3 J/C)

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 2 J/C - CAN NO. 3 J/C)

C

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 3 J/C - METER CIRCUIT PLATE)

D

9.CHECK FOR SHORT IN CONNECTED COMPONENT (ECU, SENSOR)
8.CHECK FOR SHORT IN CAN BUS LINES (CAN NO. 3 J/C)
a.

Disconnect the wire harness connector from the CAN No. 3 junction connector (engine room main wire side).


b.
U154813E02
1.25,1.74 1.25,0.969 1.25,0.969 0.906,0.969 false 1.26,2.063 1.26,2.667 1.26,2.667 0.917,2.667 false 0.167,0.146 0.49,0.417 0.323,0.271 10 false *a 0.438,1.656 0.854,1.865 0.417,0.208 10 false A68 0.333,0.865 1,1.188 0.667,0.323 10 false CANH*b 0.375,2.573 1.042,2.896 0.667,0.323 10 false CANL*b

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
A68-1 (CANH) - A68-7 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Transmission control ECU assembly


Text in Illustration
*a Front view of wire harness connector
(to CAN No. 3 Junction Connector)
*b to Transmission Control ECU Assembly



OK

REPLACE CAN NO. 3 JUNCTION CONNECTOR

NG

9.CHECK FOR SHORT IN CONNECTED COMPONENT (ECU, SENSOR)
9.CHECK FOR SHORT IN CONNECTED COMPONENT (ECU, SENSOR)
a.

Reconnect all wire harness connectors (CAN No. 1 junction connector, CAN No. 2 junction connector and CAN No. 3 junction connector).


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU (or sensor) to which the short circuited branch line is connected (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>TERMINALS OF ECU).


c.
U154762E01
0.087,0.032 0.927,0.365 0.840,0.334 10 *1 1.587,0.756 1.896,0.938 0.309,0.181 10 L61 2.452,1.066 2.863,1.247 0.411,0.181 10 CANH 2.435,2.911 2.823,3.092 0.387,0.181 10 CANL 2.078,1.828 2.441,1.27 false 2.085,2.535 2.419,2.868 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L61-6 (CANH) - L61-14 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω


Text in Illustration
*1 DLC3


HINT:
·

If the resistance becomes normal (between 54 and 69 Ω) when the connector is disconnected from the ECU (or sensor), there may be a short in the ECU (or sensor).

·

If the resistance does not become normal (between 54 and 69 Ω) when the connector is disconnected from the ECU (or sensor), repair or replace the short circuited branch line or connector.




OK

REPLACE CORRESPONDING ECU OR SENSOR

NG

REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR BUS LINE OR CONNECTOR