Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU) › 2016.05–2020.08
RM2070E _57 Power Source / Network _061936 NETWORKING _0301754 CAN COMMUNICATION SYSTEM(w/o Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(w/o Central Gateway ECU)  Check CAN Bus Line for Short to +B (LHD Models)  


DESCRIPTION

There may be a short circuit between one of the CAN bus lines and +B when no resistance exists between terminals 6 (CANH) and 16 (BAT) or 14 (CANL) and 16 (BAT) of the DLC3.

Symptom Trouble Area
No resistance exists between terminals 6 (CANH) and 16 (BAT) or 14 (CANL) and 16 (BAT) of the DLC3.
·

Short to +B in CAN main bus line

·

Short to +B in CAN branch line

·

Hybrid vehicle control ECU

·

ECM

·

Main body ECU (Multiplex network body ECU)

·

Combination meter sub-assembly

·

Brake booster with master cylinder assembly (Skid control ECU)

·

Spiral cable with sensor sub-assembly (Steering angle sensor)

·

Air conditioning amplifier assembly

·

Power steering ECU assembly

·

Airbag ECU assembly

·

Transmission control ECU assembly

·

Certification ECU (Smart key ECU assembly)

·

Radio and display receiver assembly*

·

CAN No. 1 junction connector

·

CAN No. 2 junction connector

·

CAN No. 3 junction connector



*: for Radio and Display Type

WIRING DIAGRAM

C355674E03
0.135,0.135 1.24,0.375 1.104,0.24 12 false V Bus: 1.917,0.542 3.021,0.781 1.104,0.24 10 false A57 2.25,0.542 2.708,0.771 0.458,0.229 10 false ECM 3.427,0.406 3.917,0.625 0.49,0.219 10 false 120 Ω 2.802,0.99 3.292,1.208 0.49,0.219 10 false CANL 4.125,1 4.615,1.219 0.49,0.219 10 false CANH 5.208,0.292 6.479,0.563 1.271,0.271 10 false x: Suspected Area 3.094,1.24 3.344,1.479 0.25,0.24 10 false 5 4.073,1.24 4.323,1.479 0.25,0.24 10 false 13 3.052,1.469 3.302,1.708 0.25,0.24 10 false V 4.146,1.458 4.396,1.698 0.25,0.24 10 false P 3.146,1.833 3.479,2.094 0.333,0.26 10 false A67 3.906,1.833 4.219,2.073 0.313,0.24 10 false A67 4.26,1.833 4.51,2.073 0.25,0.24 10 false 1 2.958,1.833 3.208,2.073 0.25,0.24 10 false 7 4.406,2.094 4.719,2.333 0.313,0.24 10 false A67 4.417,2.469 4.729,2.708 0.313,0.24 10 false A67 2.604,3.021 2.969,3.26 0.365,0.24 10 false L132 2.615,3.375 2.979,3.615 0.365,0.24 10 false L132 3.115,4.219 3.479,4.458 0.365,0.24 10 false L132 3.875,4.219 4.24,4.458 0.365,0.24 10 false L132 5.167,1.927 5.417,2.167 0.25,0.24 10 false LG 5.208,2.625 5.458,2.865 0.25,0.24 10 false L 5.667,1.99 5.917,2.229 0.25,0.24 10 false 37 5.656,2.573 5.906,2.813 0.25,0.24 10 false 38 5.927,1.99 6.385,2.219 0.458,0.229 10 false CA1H 5.927,2.573 6.385,2.802 0.458,0.229 10 false CA1L 5.167,2.833 5.531,3.083 0.365,0.25 10 false A58 5.49,2.833 7.135,3.583 1.646,0.75 10 false Brake Booster with Master Cylinder Assembly (Skid Control ECU) 0.854,2.094 2.896,2.385 2.042,0.292 10 false CAN No. 1 Junction Connector 2.729,2.823 2.979,3.063 0.25,0.24 10 false 5 2.677,3.573 2.927,3.813 0.25,0.24 10 false 11 1.948,2.854 2.198,3.094 0.25,0.24 10 false SB 2,3.573 2.25,3.813 0.25,0.24 10 false W 0.125,3.781 0.49,4.031 0.365,0.25 10 false L201 0.479,3.781 2.135,4.406 1.656,0.625 10 false Main Body ECU (Multiplex Network Body ECU) 1.063,2.896 1.552,3.115 0.49,0.219 10 false CANH 1.073,3.5 1.563,3.719 0.49,0.219 10 false CANL 1.542,2.885 1.792,3.125 0.25,0.24 10 false 14 1.552,3.5 1.802,3.74 0.25,0.24 10 false 13 2.865,4.219 3.115,4.458 0.25,0.24 10 false 12 4.302,4.229 4.552,4.469 0.25,0.24 10 false 6 3,4.531 3.25,4.771 0.25,0.24 10 false W 4.135,4.521 4.385,4.76 0.25,0.24 10 false B 4.406,5.135 4.771,5.375 0.365,0.24 10 false L95 3.146,4.844 3.51,5.083 0.365,0.24 10 false L94 4.26,4.823 4.51,5.063 0.25,0.24 10 false 5 2.938,4.833 3.188,5.073 0.25,0.24 10 false 4 3.896,4.844 4.26,5.083 0.365,0.24 10 false L94 4.427,5.5 4.792,5.74 0.365,0.24 10 false L95 4.406,6.406 4.771,6.646 0.365,0.24 10 false L95 4.427,6.781 4.792,7.021 0.365,0.24 10 false L95 2.635,5.875 3,6.115 0.365,0.24 10 false L95 2.646,6.24 3.01,6.479 0.365,0.24 10 false L95 0.875,5.094 2.917,5.385 2.042,0.292 10 false CAN No. 2 Junction Connector 5.885,5.125 6.375,5.344 0.49,0.219 10 false CANH 6.052,5.479 6.542,5.698 0.49,0.219 10 false CANL 4.438,4.958 4.688,5.198 0.25,0.24 10 false 14 4.469,5.698 4.719,5.938 0.25,0.24 10 false 15 5.229,4.969 5.479,5.208 0.25,0.24 10 false G 5.198,5.677 5.448,5.917 0.25,0.24 10 false W 5.604,5.021 5.854,5.26 0.25,0.24 10 false 6 5.604,5.615 5.854,5.854 0.25,0.24 10 false 14 6.292,5.688 6.74,5.875 0.448,0.188 10 false DLC3 6.01,5.688 6.354,5.917 0.344,0.229 10 false L61 2.698,5.688 2.948,5.927 0.25,0.24 10 false 5 2.708,6.448 2.958,6.688 0.25,0.24 10 false 6 2,6.427 2.25,6.667 0.25,0.24 10 false W 2.021,5.698 2.271,5.938 0.25,0.24 10 false B 1.552,5.76 1.802,6 0.25,0.24 10 false 11 1.563,6.344 1.813,6.583 0.25,0.24 10 false 12 1.083,6.354 1.573,6.573 0.49,0.219 10 false CANL 1.073,5.771 1.563,5.99 0.49,0.219 10 false CANH 0.094,6.615 0.583,6.833 0.49,0.219 10 false L17 0.375,6.615 1.927,7.469 1.552,0.854 10 false Air Conditioning Amplifier Assembly 4.49,6.229 4.74,6.469 0.25,0.24 10 false 2 4.51,6.979 4.76,7.219 0.25,0.24 10 false 3 5.188,7 5.438,7.24 0.25,0.24 10 false W 5.208,6.281 5.458,6.521 0.25,0.24 10 false R 5.646,6.323 5.896,6.563 0.25,0.24 10 false 1 5.656,6.917 5.906,7.156 0.25,0.24 10 false 7 5.844,6.323 6.333,6.542 0.49,0.219 10 false CANH 5.865,6.917 6.354,7.135 0.49,0.219 10 false CANL 4.802,7.177 5.292,7.396 0.49,0.219 10 false L54 5.115,7.177 7.042,7.635 1.927,0.458 10 false Power Steering ECU Assembly 0.813,8.01 2.698,8.25 1.885,0.24 10 false : CAN Main Bus Line (CANH) 0.802,8.427 2.688,8.667 1.885,0.24 10 false : CAN Main Bus Line (CANL) 3.948,8 5.833,8.24 1.885,0.24 10 false : CAN Branch Line (CANH) 3.948,8.396 5.833,8.635 1.885,0.24 10 false : CAN Branch Line (CANL) 4.49,1.896 4.74,2.135 0.25,0.24 10 false 2 4.521,2.677 4.771,2.917 0.25,0.24 10 false 8

C242542E17
0.792,8.01 2.708,8.198 1.917,0.188 10 false : CAN Main Bus Line (CANH) 3.979,8.031 5.698,8.219 1.719,0.188 10 false : CAN Branch Line (CANH) 3.979,8.448 5.698,8.635 1.719,0.188 10 false : CAN Branch Line (CANL) 0.792,8.406 2.708,8.594 1.917,0.188 10 false : CAN Main Bus Line (CANL) 0.813,0.458 2.802,0.646 1.99,0.188 10 false CAN No. 2 Junction Connector 0.177,6.99 2.396,7.271 2.219,0.281 10 false *: for Radio and Display Type 4.375,4.354 6.365,4.542 1.99,0.188 10 false CAN No. 3 Junction Connector 0.406,3.615 1.854,3.865 1.448,0.25 10 false Airbag ECU Assembly 5.833,1.021 6.24,1.188 0.406,0.167 10 false CANL 5.802,0.417 6.24,0.583 0.438,0.167 10 false CANH 5.813,2.646 6.219,2.813 0.406,0.167 10 false CANL 5.802,2 6.24,2.167 0.438,0.167 10 false CANH 5.813,5.396 6.219,5.563 0.406,0.167 10 false CA1L 5.802,4.76 6.24,4.927 0.438,0.167 10 false CA1H 2.781,6.74 3.188,6.906 0.406,0.167 10 false CANL 4.083,6.75 4.521,6.917 0.438,0.167 10 false CANH 1.042,1.719 1.448,1.885 0.406,0.167 10 false CANL 1.031,1.125 1.469,1.292 0.438,0.167 10 false CANH 1.021,3.313 1.427,3.479 0.406,0.167 10 false CANL 1.021,2.698 1.458,2.865 0.438,0.167 10 false CANH 4.385,0.521 4.667,0.688 0.281,0.167 10 false L94 4.396,0.896 4.677,1.063 0.281,0.167 10 false L94 4.396,2.177 4.656,2.344 0.26,0.167 10 false L95 4.396,2.531 4.646,2.698 0.25,0.167 10 false L95 3.115,3.5 3.385,3.667 0.271,0.167 10 false L94 3.865,3.5 4.135,3.667 0.271,0.167 10 false L94 3.073,4.188 3.396,4.354 0.323,0.167 10 false L133 3.094,5.844 3.448,6.01 0.354,0.167 10 false L133 3.854,5.844 4.229,6.01 0.375,0.167 10 false L133 3.833,4.198 4.24,4.365 0.406,0.167 10 false L133 2.594,1.25 2.844,1.417 0.25,0.167 10 false L94 2.583,1.615 2.844,1.781 0.26,0.167 10 false L94 2.583,2.833 2.844,3 0.26,0.167 10 false L95 2.583,3.198 2.844,3.365 0.26,0.167 10 false L95 1.51,1.125 1.698,1.354 0.188,0.229 10 false 14 2.688,1.813 2.802,1.979 0.115,0.167 10 false 7 2.656,1.052 2.771,1.219 0.115,0.167 10 false 8 1.99,1.073 2.104,1.24 0.115,0.167 10 false B 1.969,1.802 2.135,1.969 0.167,0.167 10 false W 1.5,1.729 1.677,1.896 0.177,0.167 10 false 15 1.521,2.698 1.708,2.865 0.188,0.167 10 false 13 2.677,3.406 2.792,3.573 0.115,0.167 10 false 9 4.24,3.49 4.354,3.656 0.115,0.167 10 false 2 2.906,3.49 3.021,3.656 0.115,0.167 10 false 1 2.677,2.604 2.792,2.771 0.115,0.167 10 false 8 1.938,2.635 2.052,2.802 0.115,0.167 10 false B 1.958,3.396 2.115,3.563 0.156,0.167 10 false W 1.531,3.313 1.719,3.479 0.188,0.167 10 false 22 0.083,1.99 0.479,2.24 0.396,0.25 10 false L197 5.594,0.406 5.708,0.573 0.115,0.167 10 false 4 4.417,1.094 4.604,1.26 0.188,0.167 10 false 10 4.427,2.74 4.615,2.906 0.188,0.167 10 false 12 4.427,1.979 4.615,2.146 0.188,0.167 10 false 11 2.854,4.167 3.042,4.333 0.188,0.167 10 false 11 2.844,5.844 3.031,6.01 0.188,0.167 10 false 12 4.24,4.167 4.427,4.333 0.188,0.167 10 false 5 4.24,5.833 4.427,6 0.188,0.167 10 false 6 4.417,0.344 4.604,0.51 0.188,0.167 10 false 11 5.146,0.385 5.292,0.552 0.146,0.167 10 false B 5.125,1.094 5.313,1.26 0.188,0.167 10 false W 5.125,1.99 5.271,2.156 0.146,0.167 10 false L 5.125,2.719 5.271,2.885 0.146,0.167 10 false W 4.083,6.26 4.302,6.427 0.219,0.167 10 false SB 3,6.26 3.146,6.427 0.146,0.167 10 false G 5.615,1.01 5.74,1.177 0.125,0.167 10 false 3 5.573,2.042 5.76,2.208 0.188,0.167 10 false 9 5.531,2.635 5.719,2.802 0.188,0.167 10 false 10 5.573,4.792 5.76,4.958 0.188,0.167 10 false 16 4.479,4.698 4.667,4.865 0.188,0.167 10 false 1 4.479,5.49 4.667,5.656 0.188,0.167 10 false 7 5.083,5.479 5.302,5.646 0.219,0.167 10 false BR 5.104,4.75 5.24,4.917 0.135,0.167 10 false Y 5.573,5.396 5.76,5.563 0.188,0.167 10 false 15 4.063,6.5 4.25,6.667 0.188,0.167 10 false 19 3,6.5 3.188,6.667 0.188,0.167 10 false 20 0.073,3.615 0.438,3.781 0.365,0.167 10 false L16 4.396,4.917 4.677,5.083 0.281,0.167 10 false A68 4.396,5.281 4.677,5.448 0.281,0.167 10 false A68 5.344,5.667 5.625,5.833 0.281,0.167 10 false A24 5.031,2.917 5.313,3.083 0.281,0.167 10 false L35 0.208,6.604 1.417,6.792 1.208,0.188 10 false x: Suspected Area 3.448,7.5 3.958,7.688 0.51,0.188 10 false 120 Ω 0.448,2 1.948,2.406 1.5,0.406 10 false Certification ECU (Smart Key ECU Assembly) 5.323,2.917 7.01,3.406 1.688,0.49 10 false Radio and Display Receiver Assembly* 4.677,1.281 4.969,1.458 0.292,0.177 10 false L51 5,1.281 7.135,1.844 2.135,0.563 10 false Spiral Cable with Sensor Sub-assembly (Steering Angle Sensor) 5.656,5.677 6.958,6.271 1.302,0.594 10 false Transmission Control ECU Assembly 4.573,7.208 4.844,7.406 0.271,0.198 10 false L27 4.875,7.208 6.99,7.635 2.115,0.427 10 false Combination Meter Sub-assembly 4.125,3.823 4.375,3.99 0.25,0.167 10 false GR 2.969,3.823 3.115,3.99 0.146,0.167 10 false W 0.323,5.427 1.677,5.865 1.354,0.438 10 false Hybrid Vehicle Control ECU 1.031,5.135 1.438,5.302 0.406,0.167 10 false CA1L 1.021,4.51 1.458,4.677 0.438,0.167 10 false CA1H 1.979,5.208 2.125,5.375 0.146,0.167 10 false P 1.969,4.458 2.115,4.625 0.146,0.167 10 false V 2.563,4.667 2.938,4.833 0.375,0.167 10 false L133 2.563,5.031 2.927,5.198 0.365,0.167 10 false L133 0.083,5.427 0.323,5.594 0.24,0.167 10 false L6 2.635,4.438 2.823,4.604 0.188,0.167 10 false 4 2.635,5.208 2.823,5.375 0.188,0.167 10 false 10 1.51,4.552 1.698,4.719 0.188,0.167 10 false 25 1.51,5.135 1.698,5.302 0.188,0.167 10 false 24

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the power switch on (IG), turn the cruise control system on using the cruise control switch (ON/OFF switch), wait at least 60 seconds, and then drive the vehicle at a speed of 50 km/h (31 mph) or more for at least 1.72 seconds.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>DIAGNOSIS SYSTEM).



HINT:
·

Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR SHORT TO +B IN CAN BUS LINE (CAN NO. 2 JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
U154781E02
2.781,4.229 2.688,4.229 2.688,4.229 2.448,4.083 false 0.76,0.948 1,0.948 1,0.948 1.563,1.229 false 0.771,1.208 1.01,1.208 1.01,1.208 1.563,1.417 false 0.74,2.208 1.167,2.208 1.167,2.208 1.573,1.823 false 0.75,1.865 1.177,1.865 1.177,1.865 1.573,1.646 false 2.615,2.177 2.104,2.177 2.104,2.177 1.719,1.844 false 2.594,1.875 2.083,1.875 2.083,1.875 1.74,1.646 false 2.646,0.948 2.125,0.948 2.125,0.948 1.729,1.229 false 2.656,1.208 2.427,1.208 2.427,1.208 1.74,1.427 false 0.104,0.063 0.542,0.344 0.438,0.281 10 false *a 0.042,2.979 0.198,3.156 0.156,0.177 10 false *1 2.698,0.865 3.26,1.052 0.563,0.188 10 false CANH*b 2.646,1.792 3.208,1.979 0.563,0.188 10 false CANH*d 2.656,2.083 3.219,2.271 0.563,0.188 10 false CANH*e 2.698,1.125 3.292,1.396 0.594,0.271 10 false CANH*c 0.115,0.823 0.688,1.042 0.573,0.219 10 false CANL*b 0.104,1.771 0.646,1.948 0.542,0.177 10 false CANL*d 0.115,2.135 0.656,2.313 0.542,0.177 10 false CANL*e 0.125,1.125 0.667,1.302 0.542,0.177 10 false CANL*c 1.594,0.156 2.01,0.354 0.417,0.198 10 false L94 0.219,3.656 0.531,3.833 0.313,0.177 10 false L61 2.802,4.156 3.094,4.333 0.292,0.177 10 false BAT

Disconnect the L94 wire harness connector from the CAN No. 2 junction connector (instrument panel connector holder left side).

Text in Illustration
*1 DLC3
*a Front view of wire harness connector
(to CAN No. 2 Junction Connector)
*b to CAN No. 3 Junction Connector
*c to CAN No. 1 Junction Connector
*d to Certification ECU (Smart Key ECU Assembly)
*e to Spiral Cable with Sensor Sub-assembly (Steering Angle Sensor)


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
L94-2 (CANH) - L61-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher CAN No. 3 junction connector
L94-1 (CANL) - L61-16 (BAT)
L94-5 (CANH) - L61-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher CAN No. 1 junction connector
L94-4 (CANL) - L61-16 (BAT)
L94-8 (CANH) - L61-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Certification ECU (Smart key ECU assembly)
L94-7 (CANL) - L61-16 (BAT)
L94-11 (CANH) - L61-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Spiral cable with sensor sub-assembly (Steering angle sensor)
L94-10 (CANL) - L61-16 (BAT)


Result:
Result Proceed to
OK A
NG (CAN No. 1 junction connector main line) B
NG (CAN No. 3 junction connector main line) C
NG (ECU or sensor branch line) D




A

2.CHECK FOR SHORT TO +B IN CAN BUS LINE (CAN NO. 2 JUNCTION CONNECTOR)

B

3.CHECK FOR SHORT TO +B IN CAN BUS LINE (CAN NO. 1 JUNCTION CONNECTOR)

C

5.CHECK FOR SHORT TO +B IN CAN BUS LINE (CAN NO. 3 JUNCTION CONNECTOR)

D

7.CHECK FOR SHORT TO +B IN CONNECTED COMPONENT (ECU OR SENSOR)
2.CHECK FOR SHORT TO +B IN CAN BUS LINE (CAN NO. 2 JUNCTION CONNECTOR)
a.
U154782E03
2.781,4.229 2.688,4.229 2.688,4.229 2.448,4.083 false 0.76,0.938 1,0.938 1,0.938 1.719,1.219 false 0.74,1.219 0.979,1.219 0.979,1.219 1.688,1.427 false 0.74,2.219 1.167,2.219 1.167,2.219 1.729,1.833 false 0.74,1.854 1.167,1.854 1.167,1.854 1.719,1.635 false 2.604,2.167 2.094,2.167 2.094,2.167 1.865,1.833 false 2.563,1.875 2.052,1.875 2.052,1.875 1.854,1.646 false 2.625,0.948 2.104,0.948 2.104,0.948 1.865,1.229 false 2.646,1.219 2.417,1.219 2.417,1.219 1.885,1.438 false 0.719,2.573 1.031,2.573 1.031,2.573 1.719,2.021 false 2.635,2.51 2.271,2.51 2.271,2.51 1.865,2.021 false 0.073,0.052 0.438,0.323 0.365,0.271 10 false *a 0.083,2.99 0.344,3.229 0.26,0.24 10 false *1 0.115,0.854 0.656,1.031 0.542,0.177 10 false CANH*b 0.104,1.781 0.646,1.958 0.542,0.177 10 false CANH*d 0.094,2.115 0.635,2.292 0.542,0.177 10 false CANH*e 0.125,1.146 0.667,1.323 0.542,0.177 10 false CANH*c 2.677,0.865 3.219,1.042 0.542,0.177 10 false CANL*b 2.656,1.781 3.198,1.958 0.542,0.177 10 false CANL*d 2.667,2.083 3.208,2.26 0.542,0.177 10 false CANL*e 2.698,1.135 3.24,1.313 0.542,0.177 10 false CANL*c 1.604,0.167 2.021,0.365 0.417,0.198 10 false L95 0.24,3.656 0.552,3.833 0.313,0.177 10 false L61 2.802,4.156 3.094,4.333 0.292,0.177 10 false BAT 0.125,2.49 0.667,2.667 0.542,0.177 10 false CANH*f 2.698,2.417 3.24,2.594 0.542,0.177 10 false CANL*f

Disconnect the L95 wire harness connector from the CAN No. 2 junction connector (instrument panel connector holder right side).

Text in Illustration
*1 DLC3
*a Front view of wire harness connector
(to CAN No. 2 Junction Connector)
*b to Power Steering ECU Assembly
*c to Air Conditioning Amplifier Assembly
*d to Airbag ECU Assembly
*e to Radio and Display Receiver Assembly*
*f to DLC3

*: for Radio and Display Type


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
L95-2 (CANH) - L61-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Power steering ECU assembly
L95-3 (CANL) - L61-16 (BAT)
L95-5 (CANH) - L61-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Air conditioning amplifier assembly
L95-6 (CANL) - L61-16 (BAT)
L95-8 (CANH) - L61-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Airbag ECU assembly
L95-9 (CANL) - L61-16 (BAT)
L95-11 (CANH) - L61-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Radio and display receiver assembly*
L95-12 (CANL) - L61-16 (BAT)
L95-14 (CANH) - L61-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher DLC3
L95-15 (CANL) - L61-16 (BAT)


*: for Radio and Display Type

Result:
Result Proceed to
OK A
NG (ECU or sensor branch line) B
NG (DLC3 branch line) C




A

REPLACE CAN NO. 2 JUNCTION CONNECTOR

B

7.CHECK FOR SHORT TO +B IN CONNECTED COMPONENT (ECU OR SENSOR)

C

REPAIR OR REPLACE CAN BRANCH LINE CONNECTED TO DLC3

3.CHECK FOR SHORT TO +B IN CAN BUS LINE (CAN NO. 1 JUNCTION CONNECTOR)
a.
U154822E03
2.427,4.073 2.688,4.25 2.688,4.25 2.865,4.25 false 2.031,1.479 2.031,0.667 2.031,0.667 1.833,0.667 false 2,1.813 2,2.396 2,2.396 1.74,2.396 false 2.177,1.49 2.177,0.667 2.177,0.667 2.375,0.667 false 2.167,1.802 2.167,2.396 2.167,2.396 2.427,2.396 false 0.115,2.729 0.365,2.969 0.25,0.24 10 false *1 0.115,0.115 0.365,0.354 0.25,0.24 10 false *a 1.188,0.573 1.875,0.823 0.688,0.25 10 false CANH*b 1.156,2.302 1.844,2.552 0.688,0.25 10 false CANL*b 2.438,0.583 3.125,0.833 0.688,0.25 10 false CANH*c 2.49,2.302 3.177,2.552 0.688,0.25 10 false CANL*c 2.917,4.156 3.271,4.354 0.354,0.198 10 false BAT 0.229,3.75 0.646,4 0.417,0.25 10 false L61 0.344,1.49 0.76,1.74 0.417,0.25 10 false L132

Disconnect the L132 wire harness connector from the CAN No. 1 junction connector (instrument panel wire side).

Text in Illustration
*1 DLC3
*a Front view of wire harness connector
(to CAN No. 1 Junction Connector)
*b to Main Body ECU (Multiplex Network Body ECU)
*c to CAN No. 2 Junction Connector


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
L132-5 (CANH) - L61-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Main body ECU (Multiplex network body ECU)
L132-11 (CANL) - L61-16 (BAT)
L132-6 (CANH) - L61-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher CAN No. 2 junction connector
L132-12 (CANL) - L61-16 (BAT)


Result:
Result Proceed to
OK A
NG (CAN No. 2 junction connector main line) B
NG (Main body ECU branch line) C




A

4.CHECK FOR SHORT TO +B IN CAN BUS LINE (CAN NO. 1 JUNCTION CONNECTOR)

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 1 JUNCTION CONNECTOR - CAN NO. 2 JUNCTION CONNECTOR)

C

7.CHECK FOR SHORT TO +B IN CONNECTED COMPONENT (ECU OR SENSOR)
4.CHECK FOR SHORT TO +B IN CAN BUS LINE (CAN NO. 1 JUNCTION CONNECTOR)
a.
U154823E02
2.438,4.052 2.698,4.229 2.698,4.229 2.875,4.229 false 1.281,1.49 1.281,0.677 1.281,0.677 1.083,0.677 false 1.292,1.823 1.292,2.396 1.292,2.396 1.031,2.396 false 1.458,1.5 1.458,0.677 1.458,0.677 1.656,0.677 false 1.469,1.823 1.469,2.396 1.469,2.396 1.729,2.396 false 0.094,2.729 0.344,2.969 0.25,0.24 10 false *1 0.073,0.104 0.323,0.344 0.25,0.24 10 false *a 0.5,0.583 1.188,0.833 0.688,0.25 10 false CANH*b 0.469,2.292 1.156,2.542 0.688,0.25 10 false CANL*b 1.719,0.583 2.406,0.833 0.688,0.25 10 false CANH*c 1.771,2.302 2.458,2.552 0.688,0.25 10 false CANL*c 2.896,4.146 3.25,4.344 0.354,0.198 10 false BAT 0.198,3.75 0.615,4 0.417,0.25 10 false L61 0.375,1.479 0.792,1.729 0.417,0.25 10 false A67

Disconnect the A67 wire harness connector from the CAN No. 1 junction connector (engine room main wire side).

Text in Illustration
*1 DLC3
*a Front view of wire harness connector
(to CAN No. 1 Junction Connector)
*b to ECM
*c to Brake Booster with Master Cylinder Assembly (Skid Control ECU)


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
A67-1 (CANH) - L61-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher ECM
A67-7 (CANL) - L61-16 (BAT)
A67-2 (CANH) - L61-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Brake booster with master cylinder assembly (Skid control ECU)
A67-8 (CANL) - L61-16 (BAT)


Result:
Result Proceed to
OK A
NG (ECU or sensor bus line) B




A

REPLACE CAN NO. 1 JUNCTION CONNECTOR

B

7.CHECK FOR SHORT TO +B IN CONNECTED COMPONENT (ECU OR SENSOR)
5.CHECK FOR SHORT TO +B IN CAN BUS LINE (CAN NO. 3 JUNCTION CONNECTOR)
a.
U154824E02
2.406,4.104 2.667,4.281 2.667,4.281 2.844,4.281 false 1.802,1.479 1.802,0.667 1.802,0.667 1.604,0.667 false 1.844,1.813 1.844,2.438 1.844,2.438 1.583,2.438 false 1.99,1.479 1.99,0.656 1.99,0.656 2.188,0.656 false 2,1.813 2,2.438 2,2.438 2.26,2.438 false 2.208,1.552 2.583,1.177 2.583,1.177 2.656,1.177 false 2.219,1.781 2.594,2.156 2.594,2.156 2.656,2.156 false 0.146,2.729 0.396,2.969 0.25,0.24 10 false *1 0.146,0.115 0.396,0.354 0.25,0.24 10 false *a 1.01,0.583 1.698,0.833 0.688,0.25 10 false CANH*b 1.021,2.344 1.708,2.594 0.688,0.25 10 false CANL*b 2.25,0.573 2.938,0.823 0.688,0.25 10 false CANH*c 2.323,2.344 3.01,2.594 0.688,0.25 10 false CANL*c 2.885,4.177 3.24,4.375 0.354,0.198 10 false BAT 0.198,3.75 0.615,4 0.417,0.25 10 false L61 0.344,1.479 0.76,1.729 0.417,0.25 10 false L133 2.708,1.094 3.271,1.344 0.563,0.25 10 false CANH*d 2.698,2.063 3.25,2.313 0.552,0.25 10 false CANL*d

Disconnect the L133 wire harness connector from the CAN No. 3 junction connector (instrument panel wire side).

Text in Illustration
*1 DLC3
*a Front view of wire harness connector
(to CAN No. 3 Junction Connector)
*b to Hybrid Vehicle Control ECU
*c to CAN No. 2 Junction Connector
*d to Combination Meter Sub-assembly


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
L133-4 (CANH) - L61-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Hybrid vehicle control ECU
L133-10 (CANL) - L61-16 (BAT)
L133-5 (CANH) - L61-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher CAN No. 2 junction connector
L133-11 (CANL) - L61-16 (BAT)
L133-6 (CANH) - L61-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Combination meter sub-assembly
L133-12 (CANL) - L61-16 (BAT)


Result:
Result Proceed to
OK A
NG (CAN No. 2 junction connector main line) B
NG (ECU or sensor bus line) C




A

6.CHECK FOR SHORT TO +B IN CAN BUS LINE (CAN NO. 3 JUNCTION CONNECTOR)

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 2 JUNCTION CONNECTOR - CAN NO. 3 JUNCTION CONNECTOR)

C

7.CHECK FOR SHORT TO +B IN CONNECTED COMPONENT (ECU OR SENSOR)
6.CHECK FOR SHORT TO +B IN CAN BUS LINE (CAN NO. 3 JUNCTION CONNECTOR)
a.
U154825E02
2.427,4.083 2.688,4.26 2.688,4.26 2.865,4.26 false 1.281,1.49 1.281,0.677 1.281,0.677 1.083,0.677 false 1.292,1.771 1.292,2.396 1.292,2.396 1.031,2.396 false 0.094,2.833 0.344,3.073 0.25,0.24 10 false *1 0.063,0.135 0.313,0.375 0.25,0.24 10 false *a 0.49,0.573 1.177,0.823 0.688,0.25 10 false CANH*b 0.438,2.292 1.125,2.542 0.688,0.25 10 false CANL*b 2.927,4.156 3.281,4.354 0.354,0.198 10 false BAT 0.229,3.75 0.646,4 0.417,0.25 10 false L61 0.385,1.479 0.802,1.729 0.417,0.25 10 false A68

Disconnect the A68 wire harness connector from the CAN No. 3 junction connector (engine room main wire side).

Text in Illustration
*1 DLC3
*a Front view of wire harness connector
(to CAN No. 3 Junction Connector)
*b to Transmission Control ECU Assembly


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
A68-1 (CANH) - L61-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Transmission control ECU assembly
A68-7 (CANL) - L61-16 (BAT)


Result:
Result Proceed to
OK A
NG (Transmission control ECU assembly branch line) B




A

REPLACE CAN NO. 3 JUNCTION CONNECTOR

B

7.CHECK FOR SHORT TO +B IN CONNECTED COMPONENT (ECU OR SENSOR)
7.CHECK FOR SHORT TO +B IN CONNECTED COMPONENT (ECU OR SENSOR)
a.

Reconnect all wire harness connectors.


b.

Disconnect the ECU or sensor connected to the CAN bus line that is shorted to +B.

HINT:

If the ECU or sensor has multiple connectors, disconnect the connector that includes the CAN bus lines. To determine the ECU or sensor that is connected to the shorted bus line, refer to the terminals of ECU tables (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>TERMINALS OF ECU).



c.
U154763E03
2.052,1.865 2.417,1.313 false 2.052,2.552 1.823,2.927 false 2.49,2.542 2.76,2.906 false 0.135,0.198 0.979,0.531 0.844,0.333 10 false *1 1.646,0.792 2.052,1.01 0.406,0.219 10 false L61 2.438,1.104 2.844,1.281 0.406,0.177 10 false CANH 1.531,2.948 1.917,3.125 0.385,0.177 10 false CANL 2.708,2.948 3.094,3.125 0.385,0.177 10 false BAT

Measure the resistance according to the value(s) in the table below.

Text in Illustration
*1 DLC3

Standard Resistance:
Tester Connection Condition Specified Condition
L61-6 (CANH) - L61-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
L61-14 (CANL) - L61-16 (BAT)


HINT:

If the resistance changes to 6 kΩ or higher when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.




OK

REPLACE CORRESPONDING ECU OR SENSOR

NG

REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR BUS LINE OR CONNECTOR