Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU) › 2014.11–2016.05
RM2070E _57 Power Source / Network _061936 NETWORKING _0301754 CAN COMMUNICATION SYSTEM(w/o Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(w/o Central Gateway ECU)  Check CAN Bus Line for Short to GND (RHD Models)  


DESCRIPTION

There may be a short circuit between one of the CAN bus lines and GND when there is no resistance between terminals 6 (CANH) and 4 (CG) or 14 (CANL) and 4 (CG) of the DLC3.

Symptom Trouble Area
No resistance exists between terminals 6 (CANH) and 4 (CG) or 14 (CANL) and 4 (CG) of the DLC3.
·

Short to ground in CAN main bus line

·

Short to ground in CAN branch line

·

Power management control ECU

·

ECM

·

Main body ECU (Multiplex network body ECU)

·

Combination meter sub-assembly

·

Brake booster with master cylinder assembly (Skid control ECU)

·

Spiral cable with sensor sub-assembly (Steering angle sensor)

·

Yaw rate sensor

·

Power steering ECU assembly

·

Airbag ECU assembly

·

Transmission control ECU assembly

·

Certification ECU (Smart key ECU assembly)

·

Navigation receiver assembly*1

·

Radio and display receiver assembly*2

·

CAN No. 1 junction connector

·

CAN No. 2 junction connector

·

CAN No. 3 junction connector



*1: for Navigation Receiver Type

*2: for Radio and Display Type

WIRING DIAGRAM

C262526E04
3.958,7.958 5.688,8.146 1.729,0.188 10 false : CAN Branch Line (CANH) 3.958,8.365 5.688,8.552 1.729,0.188 10 false : CAN Branch Line (CANL) 0.833,7.969 2.75,8.156 1.917,0.188 10 false : CAN Main Bus Line (CANH) 0.833,8.385 2.75,8.573 1.917,0.188 10 false : CAN Main Bus Line (CANL) 3.469,0.479 3.885,0.667 0.417,0.188 10 false 120 Ω 2.813,1.083 3.219,1.25 0.406,0.167 10 false CANL 0.167,0.708 0.458,0.875 0.292,0.167 10 false L27 4.135,1.563 4.344,1.729 0.208,0.167 10 false SB 5.125,2.948 5.26,3.115 0.135,0.167 10 false L 2.146,5.552 2.302,5.719 0.156,0.167 10 false B 2.146,6.24 2.302,6.406 0.156,0.167 10 false W 5.052,6.813 5.24,7.073 0.188,0.26 10 false W 3.01,4.198 3.167,4.365 0.156,0.167 10 false W 5.135,5.531 5.292,5.698 0.156,0.167 10 false W 4.146,4.198 4.375,4.365 0.229,0.167 10 false GR 5.156,4.781 5.313,4.948 0.156,0.167 10 false B 3.063,1.563 3.229,1.729 0.167,0.167 10 false G 3.115,1.958 3.438,2.125 0.323,0.167 10 false L132 3.104,3.927 3.51,4.094 0.406,0.167 10 false L132 3.906,4.542 4.177,4.708 0.271,0.167 10 false L94 4.417,4.979 4.74,5.146 0.323,0.167 10 false L95 4.417,5.333 4.677,5.5 0.26,0.167 10 false L95 4.427,6.26 4.729,6.427 0.302,0.167 10 false L95 4.427,6.625 4.76,6.792 0.333,0.167 10 false L95 5.417,7.042 5.698,7.208 0.281,0.167 10 false L54 3.135,4.542 3.406,4.708 0.271,0.167 10 false L94 2.635,5.708 2.896,5.875 0.26,0.167 10 false L95 2.635,6.073 2.896,6.24 0.26,0.167 10 false L95 3.875,3.917 4.271,4.083 0.396,0.167 10 false L132 3.885,1.958 4.208,2.125 0.323,0.167 10 false L132 4.417,2.396 4.708,2.563 0.292,0.167 10 false A67 4.417,2.771 4.708,2.938 0.292,0.167 10 false A67 0.49,0.708 2.688,0.917 2.198,0.208 10 false Combination Meter Sub-assembly 4.104,1.104 4.542,1.271 0.438,0.167 10 false CANH 6.094,5.281 6.5,5.448 0.406,0.167 10 false CANL 5.938,4.938 6.375,5.104 0.438,0.167 10 false CANH 1.063,6.208 1.469,6.375 0.406,0.167 10 false CANL 1.042,5.583 1.479,5.75 0.438,0.167 10 false CANH 5.885,6.76 6.292,6.927 0.406,0.167 10 false CANL 5.854,6.115 6.292,6.281 0.438,0.167 10 false CANH 5.896,2.292 6.333,2.458 0.438,0.167 10 false CA1H 5.896,2.885 6.333,3.052 0.438,0.167 10 false CA1L 4.073,1.354 4.281,1.521 0.208,0.167 10 false 19 2.854,3.938 3.063,4.104 0.208,0.167 10 false 11 2.729,6.271 2.833,6.438 0.104,0.167 10 false 5 2.729,5.479 2.844,5.646 0.115,0.167 10 false 6 5.625,5.469 5.833,5.635 0.208,0.167 10 false 14 5.594,2.292 5.802,2.458 0.208,0.167 10 false 37 5.594,2.885 5.802,3.052 0.208,0.167 10 false 38 4.458,4.75 4.635,4.917 0.177,0.167 10 false 15 4.5,6.823 4.708,6.99 0.208,0.167 10 false 2 4.51,6.031 4.719,6.198 0.208,0.167 10 false 3 5.073,2.229 5.281,2.396 0.208,0.167 10 false LG 2.854,1.906 3.052,2.073 0.198,0.167 10 false 12 3.042,1.354 3.24,1.521 0.198,0.167 10 false 20 4.313,3.927 4.427,4.094 0.115,0.167 10 false 5 4.479,5.542 4.656,5.708 0.177,0.167 10 false 14 5.667,4.844 5.781,5.01 0.115,0.167 10 false 6 4.26,4.5 4.375,4.667 0.115,0.167 10 false 1 2.948,4.5 3.063,4.667 0.115,0.167 10 false 2 4.302,1.906 4.417,2.073 0.115,0.167 10 false 6 4.521,2.177 4.635,2.344 0.115,0.167 10 false 1 1.604,6.188 1.719,6.354 0.115,0.167 10 false 2 1.604,5.583 1.719,5.75 0.115,0.167 10 false 3 5.635,6.75 5.75,6.917 0.115,0.167 10 false 7 5.635,6.146 5.75,6.313 0.115,0.167 10 false 1 4.521,2.979 4.708,3.146 0.188,0.167 10 false 7 5.25,0.563 6.458,0.75 1.208,0.188 10 false x: Suspected Area 5.094,3.167 5.438,3.354 0.344,0.188 10 false A58 5.417,3.167 7.135,3.719 1.719,0.552 10 false Brake Booster with Master Cylinder Assembly (Skid Control ECU) 6.063,5.542 6.375,5.729 0.313,0.188 10 false L61 6.354,5.542 6.75,5.729 0.396,0.188 10 false DLC3 0.896,2.813 2.885,3.313 1.99,0.5 10 false CAN No. 1 Junction Connector 0.885,5.052 2.875,5.24 1.99,0.188 10 false CAN No. 2 Junction Connector 0.24,6.49 0.531,6.646 0.292,0.156 10 false L12 0.542,6.49 1.698,6.698 1.156,0.208 10 false Yaw Rate Sensor 5.719,7.042 7.031,7.365 1.313,0.323 10 false Power Steering ECU Assembly 5.073,6.135 5.229,6.302 0.156,0.167 10 false R 0.26,0.125 1.521,0.333 1.26,0.208 12 false V Bus:

C262527E11
0.781,9.031 2.698,9.219 1.917,0.188 10 false : CAN Main Bus Line (CANH) 3.969,9.052 5.688,9.24 1.719,0.188 10 false : CAN Branch Line (CANH) 3.969,9.458 5.688,9.646 1.719,0.188 10 false : CAN Branch Line (CANL) 0.781,9.427 2.698,9.615 1.917,0.188 10 false : CAN Main Bus Line (CANL) 0.802,0.469 2.792,0.656 1.99,0.188 10 false CAN No. 2 Junction Connector 0.042,8.01 2.26,8.292 2.219,0.281 10 false *1: for Navigation Receiver Type 4.427,6.406 6.417,6.594 1.99,0.188 10 false CAN No. 3 Junction Connector 0.469,3.625 1.917,3.875 1.448,0.25 10 false Airbag ECU Assembly 5.823,1.01 6.229,1.177 0.406,0.167 10 false CANL 5.813,0.375 6.25,0.542 0.438,0.167 10 false CANH 5.802,2.635 6.208,2.802 0.406,0.167 10 false CANL 5.781,2.042 6.219,2.208 0.438,0.167 10 false CANH 5.802,5.344 6.208,5.51 0.406,0.167 10 false CA1L 5.771,4.74 6.208,4.906 0.438,0.167 10 false CA1H 2.771,7.74 3.177,7.906 0.406,0.167 10 false CANL 4.052,7.74 4.49,7.906 0.438,0.167 10 false CANH 1.031,1.688 1.438,1.854 0.406,0.167 10 false CANL 1.021,1.083 1.458,1.25 0.438,0.167 10 false CANH 1.01,3.302 1.417,3.469 0.406,0.167 10 false CANL 1,2.698 1.438,2.865 0.438,0.167 10 false CANH 4.375,0.521 4.656,0.688 0.281,0.167 10 false L94 4.375,0.896 4.656,1.063 0.281,0.167 10 false L94 4.365,2.177 4.625,2.344 0.26,0.167 10 false L95 4.365,2.531 4.615,2.698 0.25,0.167 10 false L95 3.094,3.5 3.365,3.667 0.271,0.167 10 false L94 3.865,3.5 4.135,3.667 0.271,0.167 10 false L94 3.052,4.135 3.375,4.302 0.323,0.167 10 false L133 3.104,6.875 3.458,7.042 0.354,0.167 10 false A68 3.854,6.875 4.229,7.042 0.375,0.167 10 false A68 3.823,4.146 4.229,4.313 0.406,0.167 10 false L133 2.583,1.198 2.833,1.365 0.25,0.167 10 false L94 2.583,1.573 2.844,1.74 0.26,0.167 10 false L94 2.583,2.833 2.844,3 0.26,0.167 10 false L95 2.583,3.198 2.844,3.365 0.26,0.167 10 false L95 1.531,1.094 1.646,1.26 0.115,0.167 10 false 9 2.677,1.771 2.792,1.938 0.115,0.167 10 false 8 2.688,0.979 2.802,1.146 0.115,0.167 10 false 7 2.052,1.01 2.167,1.177 0.115,0.167 10 false B 2.052,1.74 2.219,1.906 0.167,0.167 10 false W 1.5,1.688 1.677,1.854 0.177,0.167 10 false 10 1.49,2.698 1.677,2.865 0.188,0.167 10 false 13 2.667,3.375 2.781,3.542 0.115,0.167 10 false 8 4.229,3.5 4.344,3.667 0.115,0.167 10 false 4 2.896,3.5 3.01,3.667 0.115,0.167 10 false 5 2.656,2.615 2.771,2.781 0.115,0.167 10 false 9 2.031,2.646 2.146,2.813 0.115,0.167 10 false B 2.021,3.375 2.177,3.542 0.156,0.167 10 false W 1.5,3.302 1.688,3.469 0.188,0.167 10 false 22 0.073,1.969 0.333,2.135 0.26,0.167 10 false L62 5.604,0.406 5.719,0.573 0.115,0.167 10 false 4 4.406,1.094 4.594,1.26 0.188,0.167 10 false 11 4.417,2.719 4.604,2.885 0.188,0.167 10 false 11 4.417,1.938 4.604,2.104 0.188,0.167 10 false 12 2.844,4.125 3.031,4.292 0.188,0.167 10 false 12 2.896,6.885 3.083,7.052 0.188,0.167 10 false 7 4.229,4.125 4.417,4.292 0.188,0.167 10 false 6 4.229,6.885 4.417,7.052 0.188,0.167 10 false 1 4.406,0.302 4.594,0.469 0.188,0.167 10 false 10 4.979,0.375 5.125,0.542 0.146,0.167 10 false B 4.979,1.063 5.167,1.229 0.188,0.167 10 false W 4.979,2 5.125,2.167 0.146,0.167 10 false B 4.979,2.719 5.125,2.885 0.146,0.167 10 false W 4.073,7.271 4.198,7.438 0.125,0.167 10 false P 2.99,7.271 3.135,7.438 0.146,0.167 10 false V 5.604,1 5.729,1.167 0.125,0.167 10 false 3 5.563,2.052 5.75,2.219 0.188,0.167 10 false 9 5.531,2.646 5.719,2.813 0.188,0.167 10 false 10 5.531,4.74 5.719,4.906 0.188,0.167 10 false 16 4.469,4.646 4.656,4.813 0.188,0.167 10 false 2 4.469,5.427 4.656,5.594 0.188,0.167 10 false 8 4.927,5.406 5.146,5.573 0.219,0.167 10 false BR 4.958,4.719 5.094,4.885 0.135,0.167 10 false Y 5.542,5.344 5.729,5.51 0.188,0.167 10 false 15 4.052,7.51 4.24,7.677 0.188,0.167 10 false 13 3.073,7.51 3.177,7.677 0.104,0.167 10 false 5 0.167,3.625 0.448,3.792 0.281,0.167 10 false L16 4.365,4.865 4.646,5.031 0.281,0.167 10 false A68 4.375,5.229 4.656,5.396 0.281,0.167 10 false A68 5.333,5.615 5.615,5.781 0.281,0.167 10 false A24 5.073,2.917 5.354,3.083 0.281,0.167 10 false L38 0.083,7.625 1.292,7.813 1.208,0.188 10 false x: Suspected Area 3.438,8.479 3.948,8.667 0.51,0.188 10 false 120 Ω 0.365,1.969 2.125,2.344 1.76,0.375 10 false Certification ECU (Smart Key ECU Assembly) 5.385,2.917 6.698,3.313 1.313,0.396 10 false Navigation Receiver Assembly*1 4.667,1.281 4.958,1.458 0.292,0.177 10 false L51 4.99,1.281 7.125,1.844 2.135,0.563 10 false Spiral Cable with Sensor Sub-assembly (Steering Angle Sensor) 5.646,5.615 6.99,6.292 1.344,0.677 10 false Transmission Control ECU Assembly 4.76,8.198 5.031,8.396 0.271,0.198 10 false A57 5.083,8.198 5.427,8.396 0.344,0.198 10 false ECM 4.115,3.833 4.24,4 0.125,0.167 10 false B 2.958,3.833 3.104,4 0.146,0.167 10 false W 0.313,5.302 1.656,5.813 1.344,0.51 10 false Power Management Control ECU 1.021,5.021 1.427,5.188 0.406,0.167 10 false CA1L 1.01,4.396 1.448,4.563 0.438,0.167 10 false CA1H 2.01,5.073 2.156,5.24 0.146,0.167 10 false P 2.01,4.344 2.156,4.51 0.146,0.167 10 false V 2.542,4.542 2.917,4.708 0.375,0.167 10 false L133 2.552,4.896 2.917,5.063 0.365,0.167 10 false L133 0.073,5.302 0.313,5.469 0.24,0.167 10 false L6 2.667,4.323 2.854,4.49 0.188,0.167 10 false 4 2.625,5.094 2.813,5.26 0.188,0.167 10 false 10 1.5,4.427 1.688,4.594 0.188,0.167 10 false 25 1.5,5.01 1.688,5.177 0.188,0.167 10 false 24 5.385,3.542 7.125,3.99 1.74,0.448 10 false Radio and Display Receiver Assembly*2 0.042,8.406 2.823,8.688 2.781,0.281 10 false *2: for Radio and Display Receiver Type 5.073,3.552 5.354,3.719 0.281,0.167 10 false L35 0.313,6.927 1.948,7.292 1.635,0.365 10 false Main Body ECU (Multiplex Network Body ECU) 1.01,6.656 1.417,6.823 0.406,0.167 10 false CANL 1,6.031 1.438,6.198 0.438,0.167 10 false CANH 1.938,6.75 2.281,7.031 0.344,0.281 10 false W 1.885,6 2.229,6.26 0.344,0.26 10 false SB 2.552,6.167 2.927,6.333 0.375,0.167 10 false L133 2.552,6.531 2.917,6.698 0.365,0.167 10 false L133 0.073,6.927 0.344,7.094 0.271,0.167 10 false L7 2.667,5.958 2.854,6.125 0.188,0.167 10 false 5 2.625,6.729 2.813,6.896 0.188,0.167 10 false 11 1.531,6.073 1.719,6.24 0.188,0.167 10 false 14 1.531,6.646 1.719,6.813 0.188,0.167 10 false 13

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the power switch on (IG), turn the cruise control system on using the cruise control switch (ON/OFF switch), wait at least 60 seconds, and then drive the vehicle at a speed of 50 km/h (31 mph) or more for at least 1.72 seconds.

·

After the repair, perform CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>DIAGNOSIS SYSTEM).



HINT:
·

Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR SHORT TO GND IN CAN BUS LINE (CAN NO. 2 JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
U191026E02
0.75,0.948 0.99,0.948 0.99,0.948 1.552,1.229 false 0.75,1.208 0.99,1.208 0.99,1.208 1.542,1.417 false 0.75,2.24 1.177,2.24 1.177,2.24 1.583,1.854 false 0.75,1.885 1.177,1.885 1.177,1.885 1.573,1.667 false 2.615,2.188 2.104,2.188 2.104,2.188 1.719,1.854 false 2.615,1.875 2.104,1.875 2.104,1.875 1.76,1.646 false 2.615,0.948 2.125,0.948 2.125,0.948 1.729,1.229 false 2.625,1.198 2.427,1.198 2.427,1.198 1.74,1.417 false 1.927,3.021 1.802,3.021 1.802,3.021 1.635,3.5 false 0.156,0.073 0.573,0.323 0.417,0.25 10 false *a 0.094,2.979 0.313,3.208 0.219,0.229 10 false *1 0.073,0.823 0.615,1 0.542,0.177 10 false CANH*b 0.073,1.771 0.615,1.948 0.542,0.177 10 false CANH*d 0.073,2.146 0.615,2.323 0.542,0.177 10 false CANH*e 0.073,1.125 0.615,1.302 0.542,0.177 10 false CANH*c 2.667,0.854 3.208,1.031 0.542,0.177 10 false CANL*b 2.667,1.781 3.208,1.958 0.542,0.177 10 false CANL*d 2.667,2.094 3.208,2.271 0.542,0.177 10 false CANL*e 2.667,1.125 3.208,1.302 0.542,0.177 10 false CANL*c 1.594,0.188 2.01,0.385 0.417,0.198 10 false L94 0.229,3.688 0.542,3.865 0.313,0.177 10 false L61 1.99,2.938 2.281,3.115 0.292,0.177 10 false CG

Disconnect the L94 wire harness connector from the CAN No. 2 junction connector (instrument panel connector holder left side).


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
L94-1 (CANH) - L61-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher CAN No. 1 junction connector
L94-2 (CANL) - L61-4 (CG)
L94-4 (CANH) - L61-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher CAN No. 3 junction connector
L94-5 (CANL) - L61-4 (CG)
L94-7 (CANH) - L61-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Certification ECU (Smart key ECU assembly)
L94-8 (CANL) - L61-4 (CG)
L94-10 (CANH) - L61-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Spiral cable with sensor sub-assembly (Steering angle sensor)
L94-11 (CANL) - L61-4 (CG)


Text in Illustration
*1 DLC3
*a Front view of wire harness connector
(to CAN No. 2 Junction Connector)
*b to CAN No. 1 Junction Connector
*c to CAN No. 3 Junction Connector
*d to Certification ECU (Smart Key ECU Assembly)
*e to Spiral Cable with Sensor Sub-assembly (Steering Angle Sensor)

Result:
Result Proceed to
OK A
NG (CAN No. 1 junction connector main line) B
NG (CAN No. 3 junction connector main line) C
NG (ECU or sensor bus line) D




A

2.CHECK FOR SHORT TO GND IN CAN BUS LINE (CAN NO. 2 JUNCTION CONNECTOR)

B

3.CHECK FOR SHORT TO GND IN CAN BUS LINE (CAN NO. 1 JUNCTION CONNECTOR)

C

5.CHECK SHORT TO GND IN CAN BUS LINE (CAN NO. 3 JUNCTION CONNECTOR)

D

7.CHECK FOR SHORT TO GND IN CONNECTED COMPONENT (ECU, SENSOR)
2.CHECK FOR SHORT TO GND IN CAN BUS LINE (CAN NO. 2 JUNCTION CONNECTOR)
a.
U191027E02
0.75,0.927 0.99,0.927 0.99,0.927 1.708,1.208 false 0.75,1.198 0.99,1.198 0.99,1.198 1.698,1.406 false 0.729,2.24 1.156,2.24 1.156,2.24 1.719,1.854 false 0.719,1.885 1.146,1.885 1.146,1.885 1.698,1.667 false 2.615,2.188 2.104,2.188 2.104,2.188 1.875,1.854 false 2.604,1.875 2.094,1.875 2.094,1.875 1.896,1.646 false 2.625,0.948 2.135,0.948 2.135,0.948 1.896,1.229 false 2.625,1.229 2.427,1.229 2.427,1.229 1.896,1.448 false 0.719,2.583 1.031,2.583 1.031,2.583 1.719,2.031 false 2.646,2.531 2.281,2.531 2.281,2.531 1.875,2.042 false 1.927,2.99 1.823,2.99 1.823,2.99 1.646,3.479 false 0.115,0.063 0.458,0.229 0.344,0.167 10 false *a 0.083,3.01 0.24,3.188 0.156,0.177 10 false *1 2.667,0.865 3.208,1.042 0.542,0.177 10 false CANH*b 2.688,1.792 3.229,1.969 0.542,0.177 10 false CANH*d 2.688,2.104 3.229,2.281 0.542,0.177 10 false CANH*e 2.677,1.156 3.219,1.333 0.542,0.177 10 false CANH*c 0.208,0.844 0.75,1.021 0.542,0.177 10 false CANL*b 0.198,1.792 0.74,1.969 0.542,0.177 10 false CANL*d 0.198,2.146 0.74,2.323 0.542,0.177 10 false CANL*e 0.219,1.125 0.76,1.302 0.542,0.177 10 false CANL*c 1.615,0.177 2.031,0.375 0.417,0.198 10 false L95 0.229,3.677 0.542,3.854 0.313,0.177 10 false L61 1.958,2.917 2.229,3.094 0.271,0.177 10 false CG 2.688,2.448 3.229,2.625 0.542,0.177 10 false CANH*f 0.219,2.5 0.76,2.677 0.542,0.177 10 false CANL*f

Disconnect the L95 wire harness connector from the CAN No. 2 junction connector (instrument panel connector holder right side).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
L95-3 (CANH) - L61-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Power steering ECU assembly
L95-2 (CANL) - L61-4 (CG)
L95-6 (CANH) - L61-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Yaw rate sensor
L95-5 (CANL) - L61-4 (CG)
L95-9 (CANH) - L61-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Airbag ECU assembly
L95-8 (CANL) - L61-4 (CG)
L95-12 (CANH) - L61-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
·

Navigation receiver assembly*1

·

Radio and display receiver assembly*2


L95-11 (CANL) - L61-4 (CG)
L95-15 (CANH) - L61-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher DLC3
L95-14 (CANL) - L61-4 (CG)


*1: for Navigation Receiver Type

*2: for Radio and Display Type

Text in Illustration
*1 DLC3
*a Front view of wire harness connector
(to CAN No. 2 Junction Connector)
*b to Power Steering ECU Assembly
*c to Yaw Rate Sensor
*d to Airbag ECU Assembly
*e
·

to Navigation Receiver Assembly*1

·

to Radio and Display Receiver Assembly*2


*f to DLC3

*1: for Navigation Receiver Type

*2: for Radio and Display Type

Result:
Result Proceed to
OK A
NG (ECU or sensor bus line) B
NG (DLC3 branch line) C




A

REPLACE CAN NO. 2 JUNCTION CONNECTOR

B

7.CHECK FOR SHORT TO GND IN CONNECTED COMPONENT (ECU, SENSOR)

C

REPAIR OR REPLACE CAN BRANCH LINE CONNECTED TO DLC3

3.CHECK FOR SHORT TO GND IN CAN BUS LINE (CAN NO. 1 JUNCTION CONNECTOR)
a.
U154826E03
2,1.51 2,0.688 2,0.688 1.802,0.688 false 2.031,1.792 2.031,2.333 2.031,2.333 1.771,2.333 false 2.167,1.51 2.167,0.688 2.167,0.688 2.365,0.688 false 2.198,1.792 2.198,2.344 2.198,2.344 2.458,2.344 false 1.875,2.969 1.802,2.969 1.802,2.969 1.635,3.5 false 0.115,2.677 0.365,2.917 0.25,0.24 10 false *1 0.115,0.052 0.365,0.292 0.25,0.24 10 false *a 1.229,0.594 1.917,0.844 0.688,0.25 10 false CANH*b 1.208,2.24 1.896,2.49 0.688,0.25 10 false CANL*b 2.427,0.594 3.115,0.844 0.688,0.25 10 false CANH*c 2.5,2.26 3.188,2.51 0.688,0.25 10 false CANL*c 1.927,2.875 2.24,3.135 0.313,0.26 10 false CG 0.24,3.75 0.656,4 0.417,0.25 10 false L61 0.354,1.479 0.771,1.729 0.417,0.25 10 false L132

Disconnect the L132 wire harness connector from the CAN No. 1 junction connector (instrument panel wire side).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
L132-5 (CANH) - L61-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher CAN No. 2 junction connector
L132-11 (CANL) - L61-4 (CG)
L132-6 (CANH) - L61-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Combination meter sub-assembly
L132-12 (CANL) - L61-4 (CG)


Text in Illustration
*1 DLC3
*a Front view of wire harness connector
(to CAN No. 1 Junction Connector)
*b to CAN No. 2 Junction Connector
*c to Combination Meter Sub-assembly

Result:
Result Proceed to
OK A
NG (CAN No. 2 junction connector main line) B
NG (Combination meter sub-assembly main line) C




A

4.CHECK SHORT TO GND IN CAN BUS LINE (CAN NO. 1 JUNCTION CONNECTOR)

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 1 JUNCTION CONNECTOR - CAN NO. 2 JUNCTION CONNECTOR)

C

7.CHECK FOR SHORT TO GND IN CONNECTED COMPONENT (ECU, SENSOR)
4.CHECK SHORT TO GND IN CAN BUS LINE (CAN NO. 1 JUNCTION CONNECTOR)
a.
U191049E02
1.292,1.458 1.292,0.635 1.292,0.635 1.094,0.635 false 1.292,1.823 1.292,2.448 1.292,2.448 1.031,2.448 false 1.844,2.979 1.76,2.979 1.76,2.979 1.635,3.479 false 0.115,2.896 0.365,3.135 0.25,0.24 10 false *1 0.073,0.406 0.323,0.646 0.25,0.24 10 false *a 0.542,0.573 1.229,0.823 0.688,0.25 10 false CANH*b 0.479,2.365 1.167,2.615 0.688,0.25 10 false CANL*b 1.885,2.896 2.156,3.094 0.271,0.198 10 false CG 0.219,3.76 0.635,4.01 0.417,0.25 10 false L61 0.375,1.49 0.792,1.74 0.417,0.25 10 false A67

Disconnect the A67 wire harness connector from the CAN No. 1 junction connector (engine room main wire side).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
A67-1 (CANH) - L61-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Brake booster with master cylinder assembly (Skid control ECU)
A67-7 (CANL) - L61-4 (CG)


Text in Illustration
*1 DLC3
*a Front view of wire harness connector
(to CAN No. 1 Junction Connector)
*b to Brake Booster with Master Cylinder Assembly (Skid Control ECU)

Result:
Result Proceed to
OK A
NG (ECU or sensor bus line) B




A

REPLACE CAN NO. 1 JUNCTION CONNECTOR

B

7.CHECK FOR SHORT TO GND IN CONNECTED COMPONENT (ECU, SENSOR)
5.CHECK SHORT TO GND IN CAN BUS LINE (CAN NO. 3 JUNCTION CONNECTOR)
a.
U191052E02
1.823,1.469 1.823,0.646 1.823,0.646 1.625,0.646 false 1.844,1.854 1.844,2.479 1.844,2.479 1.583,2.479 false 2.177,1.438 2.177,0.615 2.177,0.615 2.375,0.615 false 2.177,1.854 2.177,2.479 2.177,2.479 2.438,2.479 false 1.854,3.063 1.75,3.063 1.75,3.063 1.646,3.5 false 2,1.458 2,0.333 2,0.333 1.74,0.333 false 2,1.854 2,2.75 2,2.75 1.75,2.75 false 0.104,2.917 0.354,3.156 0.25,0.24 10 false *1 0.083,0.156 0.333,0.396 0.25,0.24 10 false *a 1.073,0.563 1.76,0.813 0.688,0.25 10 false CANH*b 1.063,2.396 1.75,2.646 0.688,0.25 10 false CANL*b 2.417,0.531 3.104,0.781 0.688,0.25 10 false CANH*d 2.479,2.406 3.167,2.656 0.688,0.25 10 false CANL*d 1.906,2.969 2.146,3.167 0.24,0.198 10 false CG 0.188,3.771 0.604,4.021 0.417,0.25 10 false L61 0.344,1.49 0.76,1.74 0.417,0.25 10 false L133 1.219,0.25 1.906,0.5 0.688,0.25 10 false CANH*c 1.25,2.656 1.938,2.906 0.688,0.25 10 false CANL*c

Disconnect the L133 wire harness connector from the CAN No. 3 junction connector (instrument panel wire side).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
L133-4 (CANH) - L61-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Power management control ECU
L133-10 (CANL) - L61-4 (CG)
L133-5 (CANH) - L61-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Main body ECU (multiplex network body ECU)
L133-11 (CANL) - L61-4 (CG)
L133-6 (CANH) - L61-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher CAN No. 2 junction connector
L133-12 (CANL) - L61-4 (CG)


Text in Illustration
*1 DLC3
*a Front view of wire harness connector
(to CAN No. 3 Junction Connector)
*b to Power Management Control ECU
*c to Main Body ECU (Multiplex Network Body ECU)
*d to CAN No. 2 Junction Connector

Result:
Result Proceed to
OK A
NG (CAN No. 2 junction connector main line) B
NG (ECU or sensor bus line) C




A

6.CHECK SHORT TO GND IN CAN BUS LINE (CAN NO. 3 JUNCTION CONNECTOR)

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 2 JUNCTION CONNECTOR - CAN NO. 3 JUNCTION CONNECTOR)

C

7.CHECK FOR SHORT TO GND IN CONNECTED COMPONENT (ECU, SENSOR)
6.CHECK SHORT TO GND IN CAN BUS LINE (CAN NO. 3 JUNCTION CONNECTOR)
a.
U191050E02
1.292,1.479 1.292,0.656 1.292,0.656 1.094,0.656 false 1.292,1.854 1.292,2.479 1.292,2.479 1.031,2.479 false 1.479,1.469 1.479,0.646 1.479,0.646 1.677,0.646 false 1.469,1.854 1.469,2.479 1.469,2.479 1.729,2.479 false 1.875,2.979 1.781,2.979 1.781,2.979 1.656,3.49 false 0.125,2.792 0.375,3.031 0.25,0.24 10 false *1 0.083,0.188 0.333,0.427 0.25,0.24 10 false *a 0.51,0.583 1.198,0.833 0.688,0.25 10 false CANH*b 0.51,2.396 1.198,2.646 0.688,0.25 10 false CANL*b 1.927,2.896 2.188,3.094 0.26,0.198 10 false CG 0.219,3.76 0.635,4.01 0.417,0.25 10 false L61 0.375,1.5 0.792,1.75 0.417,0.25 10 false A68 1.719,0.563 2.406,0.813 0.688,0.25 10 false CANH*c 1.781,2.396 2.469,2.646 0.688,0.25 10 false CANL*c

Disconnect the A68 wire harness connector from the CAN No. 3 junction connector (engine room main wire side).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
A68-1 (CANH) - L61-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher ECM
A68-7 (CANL) - L61-4 (CG)
A68-2 (CANH) - L61-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Transmission control ECU assembly
A68-8 (CANL) - L61-4 (CG)


Text in Illustration
*1 DLC3
*a Front view of wire harness connector
(to CAN No. 3 Junction Connector)
*b to ECM
*c to Transmission Control ECU Assembly

Result:
Result Proceed to
OK A
NG (ECU or sensor bus line) B




A

REPLACE CAN NO. 3 JUNCTION CONNECTOR

B

7.CHECK FOR SHORT TO GND IN CONNECTED COMPONENT (ECU, SENSOR)
7.CHECK FOR SHORT TO GND IN CONNECTED COMPONENT (ECU, SENSOR)
a.

Reconnect all wire harness connectors (CAN No. 1 junction connector, CAN No. 2 junction connector and CAN No. 3 junction connector).


b.

Disconnect the ECU or sensor connected to the CAN bus line that is shorted to ground.

HINT:

If the ECU or sensor has multiple connectors, disconnect the connector that includes the CAN bus lines. To determine the ECU or sensor that is connected to the shorted bus line, refer to the terminals of ECU tables (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>TERMINALS OF ECU).



c.
U154764E03
2.052,1.865 2.417,1.313 false 2.052,2.552 2.281,2.896 false 1.625,1.875 1.208,1.323 false 0.083,0.031 0.927,0.365 0.844,0.333 10 false *1 1.667,0.802 1.979,0.979 0.313,0.177 10 false L61 2.344,1.135 2.75,1.313 0.406,0.177 10 false CANH 1,1.125 1.417,1.354 0.417,0.229 10 false CG 2.229,2.917 2.656,3.125 0.427,0.208 10 false CANL

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L61-6 (CANH) - L61-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L61-14 (CANL) - L61-4 (CG)


Text in Illustration
*1 DLC3

HINT:

If the resistance changes to 200 Ω or higher when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.




OK

REPLACE CORRESPONDING ECU OR SENSOR

NG

REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR BUS LINE OR CONNECTOR