Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU) › 2012.03–2014.11
RM2070E _57 Power Source / Network _061936 NETWORKING _0301754 CAN COMMUNICATION SYSTEM(w/o Central Gateway ECU) C

NETWORKING  CAN COMMUNICATION SYSTEM(w/o Central Gateway ECU)  U1100  Lost Communication with Seat Belt Control ECU  


DESCRIPTION

DTC No. DTC Detection Condition Trouble Area
U1100 No communication from the seat belt control ECU continues.
·

Seat belt control ECU branch line or connector

·

Power source circuit of seat belt control ECU

·

Seat belt control ECU ground circuit

·

Seat belt control ECU



HINT:

This diagnosis procedure is for when DTC U1100 is output by the power management control ECU (GTS display: PM1 Gateway).


WIRING DIAGRAM

C243469E03
0.74,2.344 1.135,2.49 0.396,0.146 10 false 120 Ω 6.167,2.333 6.563,2.479 0.396,0.146 10 false 120 Ω 5.75,2.802 7.052,3.552 1.302,0.75 10 false Power Management Control ECU 3.198,3.271 3.656,3.417 0.458,0.146 10 false CANH 2.969,4.344 4.698,4.646 1.729,0.302 10 false Seat Belt Control ECU 5.229,4.021 6.135,4.208 0.906,0.188 10 false Trouble Area 3.031,3.979 3.417,4.125 0.385,0.146 10 false IG1 2.76,3.792 2.938,3.938 0.177,0.146 10 false 8 3.188,3.073 3.365,3.219 0.177,0.146 10 false 1 4.115,3.083 4.292,3.229 0.177,0.146 10 false 2 4.542,3.51 4.719,3.656 0.177,0.146 10 false 8 3.948,3.677 4.396,3.823 0.448,0.146 10 false PGND 3.75,3.271 4.208,3.417 0.458,0.146 10 false CANL 1.417,5.031 3.354,5.208 1.938,0.177 10 false : CAN Main Bus Line (CANH) 1.427,5.427 3.365,5.604 1.938,0.177 10 false : CAN Main Bus Line (CANL) 4.417,5.01 6.146,5.188 1.729,0.177 10 false : CAN Branch Line (CANH) 4.406,5.406 6.104,5.583 1.698,0.177 10 false : CAN Branch Line (CANL) 2.729,3.979 3.021,4.156 0.292,0.177 10 false L3 0.313,2.833 1.74,3.375 1.427,0.542 10 false CAN No. 4 Junction Connector 1.865,4.167 2.906,4.344 1.042,0.177 10 false ECU-IG NO. 2 3.031,3.458 3.417,3.604 0.385,0.146 10 false +B 2.76,3.271 2.938,3.417 0.177,0.146 10 false 7 2.729,3.469 3.021,3.646 0.292,0.177 10 false L2 2.167,3.615 2.479,3.792 0.313,0.177 10 false PSB 4.51,3.698 4.802,3.875 0.292,0.177 10 false L2 3.417,3.083 3.708,3.26 0.292,0.177 10 false L3 3.833,3.073 4.125,3.25 0.292,0.177 10 false L3 0.135,0.104 1.781,0.854 1.646,0.75 12 false Sub Bus 11: 5.51,2.802 5.688,2.979 0.177,0.177 10 false L5

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the power switch on (IG) and wait at least 20 seconds.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>DIAGNOSIS SYSTEM).



HINT:
·

Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.RECONFIRM DTC OUTPUT
a.

Reconfirm DTCs.

HINT:

If DTC U1002 is output from PM1 Gateway of the power management control ECU, this indicates a sub bus 11 malfunction. Troubleshoot for DTC U1002 and check for malfunctions in sub bus 11.


Result:
Result Proceed to
U1002 is not output from power management control ECU (GTS display: PM1 Gateway) A
U1002 is output from power management control ECU (GTS display: PM1 Gateway) B




A

2.CHECK FOR OPEN IN CAN BUS LINES (SEAT BELT CONTROL ECU BRANCH LINE)

B

GO TO DIAGNOSIS PROCEDURE INDICATED BY OUTPUT DTC

2.CHECK FOR OPEN IN CAN BUS LINES (SEAT BELT CONTROL ECU BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
U190988E02
1.448,2.125 0.875,2.271 false 1.667,2.156 1.875,2.76 false 0.125,0.073 2.479,0.406 2.354,0.333 10 false *a 1.677,1.135 2.01,1.313 0.333,0.177 10 false L3 1.74,2.771 2.198,2.979 0.458,0.208 10 false CANL 0.458,2.219 0.917,2.385 0.458,0.167 10 false CANH

Disconnect the seat belt control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L3-1 (CANH) - L3-2 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Seat Belt Control ECU)



OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (SEAT BELT CONTROL ECU)

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
U191003E02
1.833,1.927 2.063,2.458 false 0.115,0.104 0.719,0.385 0.604,0.281 10 false *a 2.063,2.469 2.479,2.646 0.417,0.177 10 false PGND 1.656,0.719 1.917,0.896 0.26,0.177 10 false L2

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L2-8 (PGND) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Seat Belt Control ECU)


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Disconnect the seat belt control ECU connectors.


d.
U191014E02
1.25,4.198 1.552,3.781 false 1.875,1.875 1.875,2.26 false 0.135,0.135 0.604,0.385 0.469,0.25 10 false *a 1.76,2.271 2.052,2.448 0.292,0.177 10 false IG1 1.021,4.167 1.208,4.344 0.188,0.177 10 false +B 0.521,1.406 0.875,1.656 0.354,0.25 10 false L3 0.531,3.604 0.885,3.875 0.354,0.271 10 false L2

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L2-7 (+B) - Body ground Power switch off 11 to 14 V
L3-8 (IG1) - Body ground Power switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Seat Belt Control ECU)



OK

REPLACE SEAT BELT CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)