Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU) › 2012.03–2014.11
RM2070E _57 Power Source / Network _061936 NETWORKING _0301754 CAN COMMUNICATION SYSTEM(w/o Central Gateway ECU) C

NETWORKING  CAN COMMUNICATION SYSTEM(w/o Central Gateway ECU)  U0104  Lost Communication with Driving Support ECU  


DESCRIPTION

DTC No. DTC Detection Condition Trouble Area
U0104 No communication from the driving support ECU continues.
·

Driving support ECU assembly branch line or connector

·

Power source circuit of driving support ECU assembly

·

Driving support ECU assembly ground circuit

·

Driving support ECU assembly



HINT:

This diagnosis procedure is for when DTC U0104 is output by the power management control ECU (GTS display: PM1 Gateway).


WIRING DIAGRAM

C240391E04
0.344,2.844 1.76,3.552 1.417,0.708 10 false CAN No. 4 Junction Connector 0.74,2.333 1.135,2.479 0.396,0.146 10 false 120 Ω 6.167,2.323 6.563,2.469 0.396,0.146 10 false 120 Ω 5.75,2.833 7.052,3.583 1.302,0.75 10 false Power Management Control ECU 3.375,3.292 3.813,3.438 0.438,0.146 10 false CA2H 3.167,4.083 5.125,4.229 1.958,0.146 10 false Driving Support ECU Assembly 3.344,4.604 4.25,4.792 0.906,0.188 10 false Trouble Area 3.167,3.542 3.344,3.688 0.177,0.146 10 false B 2.938,3.458 3.115,3.604 0.177,0.146 10 false 30 3.469,3.073 3.646,3.219 0.177,0.146 10 false 39 4.063,3.073 4.24,3.219 0.177,0.146 10 false 17 4.646,3.406 4.823,3.552 0.177,0.146 10 false 25 5.51,2.833 5.688,2.979 0.177,0.146 10 false L5 4.188,3.51 4.542,3.656 0.354,0.146 10 false GND 3.917,3.292 4.365,3.438 0.448,0.146 10 false CA2L 1.417,5.021 3.354,5.198 1.938,0.177 10 false : CAN Main Bus Line (CANH) 1.417,5.417 3.354,5.594 1.938,0.177 10 false : CAN Main Bus Line (CANL) 4.396,5.021 6.125,5.198 1.729,0.177 10 false : CAN Branch Line (CANH) 4.396,5.417 6.104,5.594 1.708,0.177 10 false : CAN Branch Line (CANL) 2.875,4.073 3.135,4.25 0.26,0.177 10 false L60 2.135,3.708 3.063,3.885 0.927,0.177 10 false ECU-IG NO. 2 0.125,0.052 1.563,0.531 1.438,0.479 12 false Sub Bus 11:

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the power switch on (IG), wait at least 20 seconds, and then drive the vehicle at a speed of 50 km/h (31 mph) or more at least 1.72 seconds.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>DIAGNOSIS SYSTEM).



HINT:
·

Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.RECONFIRM DTC OUTPUT
a.

Reconfirm DTCs.

HINT:

If DTC U1002 is output from PM1 Gateway of the power management control ECU, this indicates a sub bus 11 malfunction. Troubleshoot for DTC U1002 and check for malfunctions in sub bus 11.


Result:
Result Proceed to
U1002 is not output from power management control ECU (GTS display: PM1 Gateway) A
U1002 is output from power management control ECU (GTS display: PM1 Gateway) B




A

2.CHECK FOR OPEN IN CAN BUS LINES (DRIVING SUPPORT ECU ASSEMBLY BRANCH LINE)

B

GO TO DIAGNOSIS PROCEDURE INDICATED BY OUTPUT DTC

2.CHECK FOR OPEN IN CAN BUS LINES (DRIVING SUPPORT ECU ASSEMBLY BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
U155038E02
2.698,1.896 2.875,2.604 false 2.729,1.74 2.885,1.198 false 0.094,0.115 0.448,0.385 0.354,0.271 10 false *a 2.688,2.667 3.177,2.854 0.49,0.188 10 false CA2H 2.74,0.99 3.229,1.177 0.49,0.188 10 false CA2L 0.438,1.031 0.844,1.208 0.406,0.177 10 false L60

Disconnect the driving support ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L60-39 (CA2H) - L60-17 (CA2L) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Driving Support ECU Assembly)



OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (DRIVING SUPPORT ECU ASSEMBLY)

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
U155039E02
1.313,1.906 0.979,2.646 false 0.156,0.104 0.51,0.375 0.354,0.271 10 false *a 0.823,2.677 1.313,2.865 0.49,0.188 10 false GND 0.427,1.063 0.833,1.24 0.406,0.177 10 false L60

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L60-25 (GND) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Driving Support ECU Assembly)


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.
U155040E02
1.75,1.906 1.99,2.625 false 0.167,0.156 0.521,0.427 0.354,0.271 10 false *a 1.969,2.677 2.375,2.865 0.406,0.188 10 false B 0.427,1.042 0.833,1.219 0.406,0.177 10 false L60

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L60-30 (B) - Body ground Power switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Driving Support ECU Assembly)



OK

REPLACE DRIVING SUPPORT ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)