Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU) › 2014.11–2016.05
RM2070E _57 Power Source / Network _061936 NETWORKING _0301754 CAN COMMUNICATION SYSTEM(w/o Central Gateway ECU) C

NETWORKING  CAN COMMUNICATION SYSTEM(w/o Central Gateway ECU)  U0100  Lost Communication with ECM / PCM  


DESCRIPTION

DTC No. DTC Detection Condition Trouble Area
U0100 No communication from the ECM continues.
·

ECM main line or connector

·

Power source circuit of ECM

·

ECM ground circuit

·

ECM



HINT:

This diagnosis procedure is for when DTC U0100 is output by the power management control ECU (GTS display: PM2 Gateway).


WIRING DIAGRAM

C240389E09
2.313,3.083 2.156,2.781 2.156,2.781 2.01,2.781 false 3.417,3.083 3.167,2.208 3.167,2.208 2.823,2.208 false 4.729,4.24 5.167,4.563 0.438,0.323 10 false 120 Ω 0.781,3.99 1.219,4.313 0.438,0.323 10 false 120 Ω 5.583,2.823 6.781,3.167 1.198,0.344 10 false to EFI MAIN Relay 5.573,3.146 5.833,3.323 0.26,0.177 10 false A57 4.177,3.24 4.438,3.417 0.26,0.177 10 false A57 4.188,3.865 4.448,4.042 0.26,0.177 10 false A57 5.573,3.552 5.833,3.729 0.26,0.177 10 false A57 5.573,3.979 5.833,4.156 0.26,0.177 10 false A57 5.583,4.396 5.906,4.573 0.323,0.177 10 false D28 4.854,4.635 5.365,4.885 0.51,0.25 10 false ECM 5.625,4.177 5.792,4.354 0.167,0.177 10 false 28 5.573,4.604 5.823,4.781 0.25,0.177 10 false 104 5.667,3.344 5.823,3.521 0.156,0.177 10 false 2 5.656,3.75 5.813,3.927 0.156,0.177 10 false 1 5.292,3.135 5.479,3.313 0.188,0.177 10 false +B 5.219,3.542 5.49,3.719 0.271,0.177 10 false +B2 5.104,3.979 5.531,4.156 0.427,0.177 10 false IGSW 6.292,4.01 6.698,4.438 0.406,0.427 10 false IGN Fuse 5.313,4.375 5.5,4.552 0.188,0.177 10 false E1 4.208,3.469 4.375,3.646 0.167,0.177 10 false 12 4.26,4.073 4.427,4.25 0.167,0.177 10 false 4 0.313,4.625 1.583,5.188 1.271,0.563 10 false Power Management Control ECU 5.323,5.042 6.271,5.417 0.948,0.375 10 false Trouble Area 1.271,0.625 3.563,0.969 2.292,0.344 10 false : CAN Main Bus Line (CANH) 1.281,0.969 3.573,1.313 2.292,0.344 10 false : CAN Main Bus Line (CANL) 4.552,4.01 4.958,4.188 0.406,0.177 10 false CANN 4.521,3.135 4.927,3.313 0.406,0.177 10 false CANP 0.063,2.698 2,2.875 1.938,0.177 10 false CAN No. 5 Junction Connector 0.896,2.125 2.833,2.302 1.938,0.177 10 false CAN No. 1 Junction Connector 0.073,0.094 1.125,0.458 1.052,0.365 12 false Sub Bus 12:

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the power switch on (IG) and wait at least 20 seconds.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>DIAGNOSIS SYSTEM).



HINT:
·

Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.RECONFIRM DTC OUTPUT
a.

Reconfirm DTCs.

HINT:

If DTC U1002 is output from PM2 Gateway of the power management control ECU, this indicates a sub bus 12 malfunction. Troubleshoot for DTC U1002 and check for malfunctions in sub bus 12.


Result:
Result Proceed to
U1002 is not output from power management control ECU (GTS display: PM2 Gateway) A
U1002 is output from power management control ECU (GTS display: PM2 Gateway) B




A

2.CHECK FOR OPEN IN CAN BUS LINES (ECM - SUB BUS 12)

B

GO TO DIAGNOSIS PROCEDURE INDICATED BY OUTPUT DTC

2.CHECK FOR OPEN IN CAN BUS LINES (ECM - SUB BUS 12)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
U154224E02
1.698,1.656 1.365,2.573 false 1.469,1.135 1.698,1.594 false 0.146,0.104 0.917,0.427 0.771,0.323 10 false *a 0.26,1.771 0.615,2.021 0.354,0.25 10 false A57 1.135,0.948 1.667,1.094 0.531,0.146 10 false CANN 1.104,2.615 1.646,2.865 0.542,0.25 10 false CANP

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A57-12 (CANP) - A57-4 (CANN) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to ECM)



OK

3.CHECK ECM POWER SOURCE CIRCUIT

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (ECM MAIN LINE)

3.CHECK ECM POWER SOURCE CIRCUIT

OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)