Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU) › 2014.11–2016.05
RM2070E _57 Power Source / Network _061936 NETWORKING _0301754 CAN COMMUNICATION SYSTEM(w/o Central Gateway ECU) C

NETWORKING  CAN COMMUNICATION SYSTEM(w/o Central Gateway ECU)  U1002  Lost Communication with Gateway Module (Power Management2)  


DESCRIPTION

·

The power management control ECU will store this DTC when no signals can be received from the ECUs that have been memorized as those that are connected to sub bus 12.

·

When the power management control ECU receives a response signal from the ECUs connected to sub bus 12, the power management control ECU recognizes and memorizes that the ECU is connected to sub bus 12. Based on this memorized data, the power management control ECU monitors for malfunctions in the ECUs connected to sub bus 12 when communicating with those ECUs. If the power management control ECU cannot receive response signals from the ECUs that have been memorized as those connected to sub bus 12, the power management control ECU determines that a malfunction exists.


DTC No. DTC Detection Condition Trouble Area
U1002 Power management control ECU cannot receive signals from all ECUs that have been memorized as those connected to sub bus 12.
·

Open or short in sub bus 12 main line or connector

·

Open or short in sub bus 12 branch line or connector

·

Power management control ECU

·

ECM

·

Air conditioning amplifier assembly

·

Brake booster with master cylinder assembly (Skid control ECU)

·

CAN No. 1 junction connector

·

CAN No. 5 junction connector



HINT:

This diagnosis procedure is for when DTC U1002 is output by the power management control ECU (GTS display: PM2 Gateway).


WIRING DIAGRAM

C242869E04
5.271,0.708 6.479,0.896 1.208,0.188 10 false x: Suspected Area 1.302,0.625 2.552,1.052 1.25,0.427 10 false Power Management Control ECU 3.396,0.427 3.813,0.615 0.417,0.188 10 false 120 Ω 0.427,5.49 2.781,6.208 2.354,0.719 10 false Brake Booster with Master Cylinder Assembly (Skid Control ECU) 5.51,3.323 7.094,3.677 1.583,0.354 10 false Air Conditioning Amplifier Assembly 3.396,7.344 3.813,7.531 0.417,0.188 10 false 120 Ω 4.99,7.052 5.365,7.229 0.375,0.177 10 false ECM 4.396,4.646 6.656,4.833 2.26,0.188 10 false CAN No. 1 Junction Connector 0.833,2.563 2.823,2.75 1.99,0.188 10 false CAN No. 5 Junction Connector 3.625,7.927 5.333,8.115 1.708,0.188 10 false : CAN Branch Line (CANH) 3.625,8.333 5.333,8.521 1.708,0.188 10 false : CAN Branch Line (CANL) 0.958,7.938 2.875,8.125 1.917,0.188 10 false : CAN Main Bus Line (CANH) 0.958,8.354 2.875,8.542 1.917,0.188 10 false : CAN Main Bus Line (CANL) 2.719,1.01 3.104,1.177 0.385,0.167 10 false CA3N 0.99,4.552 1.375,4.719 0.385,0.167 10 false CA2H 1.042,5.188 1.427,5.354 0.385,0.167 10 false CA2L 3.042,2.094 3.396,2.26 0.354,0.167 10 false L102 3.052,4.146 3.417,4.313 0.365,0.167 10 false L132 3.802,4.156 4.167,4.323 0.365,0.167 10 false L132 3.813,2.094 4.208,2.26 0.396,0.167 10 false L102 4.323,2.563 4.677,2.729 0.354,0.167 10 false L101 5.219,3.323 5.51,3.49 0.292,0.167 10 false L17 4.333,2.927 4.688,3.094 0.354,0.167 10 false L101 3.802,3.552 4.188,3.719 0.385,0.167 10 false L101 3.052,3.542 3.448,3.708 0.396,0.167 10 false L101 2.563,4.708 2.854,4.875 0.292,0.167 10 false A67 2.573,5.073 2.865,5.24 0.292,0.167 10 false A67 3.073,5.594 3.365,5.76 0.292,0.167 10 false A67 4.656,7.052 4.948,7.219 0.292,0.167 10 false A57 3.833,5.604 4.125,5.771 0.292,0.167 10 false A67 3,1.281 3.208,1.448 0.208,0.167 10 false 30 1.469,4.552 1.677,4.719 0.208,0.167 10 false 35 1.469,5.188 1.677,5.354 0.208,0.167 10 false 34 2.875,2.052 3.083,2.219 0.208,0.167 10 false 3 4.198,2.052 4.406,2.219 0.208,0.167 10 false 5 4.427,2.375 4.635,2.542 0.208,0.167 10 false 1 4.427,3.115 4.635,3.281 0.208,0.167 10 false 3 2.646,4.521 2.854,4.688 0.208,0.167 10 false 3 2.073,4.552 2.281,4.719 0.208,0.167 10 false P 2.094,5.198 2.302,5.365 0.208,0.167 10 false V 2.646,5.26 2.854,5.427 0.208,0.167 10 false 9 2.958,1.74 3.167,1.906 0.208,0.167 10 false W 4.854,2.417 5.063,2.583 0.208,0.167 10 false B 4.844,3.021 5.052,3.188 0.208,0.167 10 false W 4.063,1.74 4.271,1.906 0.208,0.167 10 false B 4,1.281 4.208,1.448 0.208,0.167 10 false 31 5.521,2.448 5.729,2.615 0.208,0.167 10 false 11 5.521,3.031 5.729,3.198 0.208,0.167 10 false 12 1.063,0.625 1.271,0.792 0.208,0.167 10 false L6 0.094,5.49 0.385,5.656 0.292,0.167 10 false A58 4.063,1.01 4.448,1.177 0.385,0.167 10 false CA3P 5.75,2.406 6.188,2.573 0.438,0.167 10 false CANH 5.771,3.042 6.208,3.208 0.438,0.167 10 false CANL 4.021,6.49 4.229,6.656 0.208,0.167 10 false 12 3.01,6.49 3.219,6.656 0.208,0.167 10 false 4 2.917,6.188 3.125,6.354 0.208,0.167 10 false W 4.094,6.188 4.302,6.354 0.208,0.167 10 false B 2.802,5.594 3.01,5.76 0.208,0.167 10 false 10 4.188,5.594 4.396,5.76 0.208,0.167 10 false 4 2.875,4.125 3.083,4.292 0.208,0.167 10 false 9 4.208,4.125 4.344,4.292 0.135,0.167 10 false 3 4.198,3.542 4.406,3.708 0.208,0.167 10 false 2 2.865,3.542 3.073,3.708 0.208,0.167 10 false 4 3.01,3.875 3.219,4.042 0.208,0.167 10 false Y 4.073,3.875 4.281,4.042 0.208,0.167 10 false R 2.698,6.719 3.167,6.917 0.469,0.198 10 false CANN 4.052,6.719 4.573,6.917 0.521,0.198 10 false CANP 0.104,0.052 1.25,0.354 1.146,0.302 12 false Sub Bus 12:

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the power switch on (IG) and wait at least 20 seconds.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>DIAGNOSIS SYSTEM).



HINT:
·

Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK SUB BUS 12
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
U154830E05
2.427,1.688 2.115,1.042 2.115,1.042 1.875,1.042 false 2.635,1.698 2.885,1.01 2.885,1.01 3.042,1.01 false 2.427,1.906 2.177,2.438 2.177,2.438 2.042,2.438 false 2.469,1.906 2.625,2.438 2.625,2.438 2.74,2.438 false 2.406,0.885 2.698,1.146 0.292,0.26 10 false L6 0.125,0.063 0.479,0.417 0.354,0.354 10 false *a 1.615,2.344 2.135,2.583 0.521,0.24 10 false CA3P 2.792,2.344 3.313,2.583 0.521,0.24 10 false CA3N 1.406,0.969 1.927,1.208 0.521,0.24 10 false AM21 3.073,0.927 3.365,1.167 0.292,0.24 10 false E12

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Result
L6-31 (CA3P) - L6-30 (CA3N) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω Below 54 Ω:
Short circuit between bus lines
70 Ω or higher:
Open circuit in a main bus line
L6-31 (CA3P) - L6-4 (E12) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω:
CANH ground short
L6-30 (CA3N) - L6-4 (E12) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω:
CANL ground short



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Result
L6-31 (CA3P) - L6-7 (AM21) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ:
CANH +B short
L6-30 (CA3N) - L6-7 (AM21) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ:
CANL +B short


Text in Illustration
*a Component with harness connector
(Power Management Control ECU)

HINT:

When the value is as specified, clear and recheck for DTCs. When no DTCs are output, check for malfunctions such as damage or improper connection of the relevant connectors.


Result:
Result Proceed to
OK A
Open circuit in CAN main bus line B
Short circuit between bus lines C
·

Ground short

·

+B short


D




A

B

2.CHECK FOR OPEN IN SUB BUS 12 LINES (POWER MANAGEMENT CONTROL ECU)

C

8.CHECK FOR SHORT IN SUB BUS 12 LINES (POWER MANAGEMENT CONTROL ECU)

D

14.CHECK FOR SHORT IN SUB BUS 12 LINE (POWER MANAGEMENT CONTROL ECU)
2.CHECK FOR OPEN IN SUB BUS 12 LINES (POWER MANAGEMENT CONTROL ECU)
a.
U154251E03
2.469,2.573 2.229,2.927 false 2.427,2.573 2.042,2.573 false 2.563,0.615 2.844,0.792 0.281,0.177 10 false L6 1.74,2.917 2.198,3.094 0.458,0.177 10 false CA3N 1.615,2.479 2,2.656 0.385,0.177 10 false CA3P 0.167,0.094 0.427,0.375 0.26,0.281 10 false *a

Disconnect the power management control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L6-31 (CA3P) - L6-30 (CA3N) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Power Management Control ECU)



OK

NG

3.CHECK FOR OPEN IN SUB BUS 12 LINES (CAN NO. 5 J/C - CAN NO. 1 J/C)
3.CHECK FOR OPEN IN SUB BUS 12 LINES (CAN NO. 5 J/C - CAN NO. 1 J/C)
a.

Reconnect the power management control ECU connector.


b.

Disconnect the wire harness connector from the CAN No. 5 junction connector (instrument panel connector holder left side).


c.
U154800E03
1.781,1.74 1.781,0.969 1.781,0.969 1.938,0.969 false 1.448,1.75 1.448,0.969 1.448,0.969 1.104,0.969 false 0.125,0.094 0.385,0.313 0.26,0.219 10 false *a 0.396,1.656 0.813,1.865 0.417,0.208 10 false L101 0.542,0.885 1.208,1.208 0.667,0.323 10 false CANH*b 2,0.885 2.667,1.208 0.667,0.323 10 false CANL*b

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L101-2 (CANH) - L101-4 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to CAN No. 5 Junction Connector)
*b to CAN No. 1 Junction Connector



OK

4.CHECK FOR OPEN IN SUB BUS 12 LINES (CAN NO. 5 J/C - POWER MANAGEMENT CONTROL ECU)

NG

5.CHECK FOR OPEN IN SUB BUS 12 LINES (CAN NO. 1 J/C - CAN NO. 5 J/C)
4.CHECK FOR OPEN IN SUB BUS 12 LINES (CAN NO. 5 J/C - POWER MANAGEMENT CONTROL ECU)
a.

Reconnect the wire harness connector to the CAN No. 5 junction connector (instrument panel connector holder left side).


b.

Disconnect the wire harness connector from the CAN No. 5 junction connector (instrument panel connector holder right side).


c.
U154801E04
1.979,1.771 1.979,0.875 1.979,0.875 2.5,0.875 false 1.594,1.771 1.604,0.885 1.604,0.885 1.458,0.885 false 0.177,0.042 0.438,0.26 0.26,0.219 10 false *a 0.385,1.667 0.802,1.875 0.417,0.208 10 false L102 2.552,0.802 3.219,1.125 0.667,0.323 10 false CANH*b 0.885,0.792 1.552,1.115 0.667,0.323 10 false CANL*b

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L102-5 (CANH) - L102-3 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to CAN No. 5 Junction Connector)
*b to Power Management Control ECU



OK

REPLACE CAN NO. 5 JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 5 J/C - POWER MANAGEMENT CONTROL ECU)

5.CHECK FOR OPEN IN SUB BUS 12 LINES (CAN NO. 1 J/C - CAN NO. 5 J/C)
a.

Reconnect the wire harness connector to the CAN No. 5 junction connector (instrument panel connector holder left side).


b.

Disconnect the wire harness connector from the CAN No. 1 junction connector (instrument panel wire side).


c.
U154802E04
1.615,2.083 1.615,2.688 1.615,2.688 1.271,2.688 false 1.615,1.74 1.615,0.958 1.615,0.958 1.271,0.958 false 0.146,0.094 0.406,0.313 0.26,0.219 10 false *a 0.406,1.656 0.823,1.865 0.417,0.208 10 false L132 0.75,0.885 1.417,1.208 0.667,0.323 10 false CANH*b 0.76,2.615 1.427,2.938 0.667,0.323 10 false CANL*b

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L132-3 (CANH) - L132-9 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to CAN No. 1 Junction Connector)
*b to CAN No. 5 Junction Connector



OK

6.CHECK FOR OPEN IN SUB BUS 12 LINES (CAN NO. 1 J/C - ECM)

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 1 J/C - CAN NO. 5 J/C)

6.CHECK FOR OPEN IN SUB BUS 12 LINES (CAN NO. 1 J/C - ECM)
a.

Reconnect the wire harness connector to the CAN No. 1 junction connector (instrument panel wire side).


b.

Disconnect the wire harness connector from the CAN No. 1 junction connector (engine room main wire side).


c.
U154803E04
1.792,1.729 1.792,0.958 1.792,0.958 2.135,0.958 false 1.781,2.094 1.781,2.698 1.781,2.698 2.115,2.698 false 0.115,0.083 0.375,0.302 0.26,0.219 10 false *a 0.438,1.656 0.854,1.865 0.417,0.208 10 false A67 2.167,0.896 2.833,1.219 0.667,0.323 10 false CANH*b 2.146,2.635 2.813,2.958 0.667,0.323 10 false CANL*b

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A67-4 (CANH) - A67-10 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to CAN No. 1 Junction Connector)
*b to ECM



OK

REPLACE CAN NO. 1 JUNCTION CONNECTOR

NG

7.CHECK FOR OPEN IN SUB BUS 12 LINES (ECM)
7.CHECK FOR OPEN IN SUB BUS 12 LINES (ECM)
a.

Reconnect the wire harness connector to the CAN No. 1 junction connector (engine room main wire side).


b.
U154225E02
1.698,1.656 1.365,2.573 false 1.469,1.135 1.698,1.594 false 0.156,0.125 0.927,0.448 0.771,0.323 10 false *a 0.271,1.781 0.552,1.948 0.281,0.167 10 false A57 1.115,0.938 1.646,1.083 0.531,0.146 10 false CANN 1.042,2.615 1.5,2.76 0.458,0.146 10 false CANP

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A57-12 (CANP) - A57-4 (CANN) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to ECM)



OK

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 1 J/C - ECM)

8.CHECK FOR SHORT IN SUB BUS 12 LINES (POWER MANAGEMENT CONTROL ECU)
a.
U154251E03
2.469,2.573 2.229,2.927 false 2.427,2.573 2.042,2.573 false 2.563,0.615 2.844,0.792 0.281,0.177 10 false L6 1.74,2.917 2.198,3.094 0.458,0.177 10 false CA3N 1.615,2.479 2,2.656 0.385,0.177 10 false CA3P 0.167,0.094 0.427,0.375 0.26,0.281 10 false *a

Disconnect the power management control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L6-31 (CA3P) - L6-30 (CA3N) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Power Management Control ECU)



OK

NG

9.CHECK FOR SHORT IN SUB BUS 12 LINES (CAN NO. 5 J/C - POWER MANAGEMENT CONTROL ECU)
9.CHECK FOR SHORT IN SUB BUS 12 LINES (CAN NO. 5 J/C - POWER MANAGEMENT CONTROL ECU)
a.

Reconnect the power management control ECU connector.


b.

Disconnect the wire harness connector from the CAN No. 5 junction connector (instrument panel connector holder right side).


c.
U154801E04
1.979,1.771 1.979,0.875 1.979,0.875 2.5,0.875 false 1.594,1.771 1.604,0.885 1.604,0.885 1.458,0.885 false 0.177,0.042 0.438,0.26 0.26,0.219 10 false *a 0.385,1.667 0.802,1.875 0.417,0.208 10 false L102 2.552,0.802 3.219,1.125 0.667,0.323 10 false CANH*b 0.885,0.792 1.552,1.115 0.667,0.323 10 false CANL*b

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L102-5 (CANH) - L102-3 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to CAN No. 5 Junction Connector)
*b to Power Management Control ECU



OK

10.CHECK FOR SHORT IN SUB BUS 12 LINES (CAN NO. 5 J/C)

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 5 J/C - POWER MANAGEMENT CONTROL ECU)

10.CHECK FOR SHORT IN SUB BUS 12 LINES (CAN NO. 5 J/C)
a.

Disconnect the wire harness connector from the CAN No. 5 junction connector (instrument panel connector holder left side).


b.
U154804E03
1.438,1.719 1.438,0.948 1.438,0.948 1.781,0.948 false 1.26,1.74 1.26,0.958 1.26,0.958 0.927,0.958 false 1.26,2.74 1.604,2.74 1.604,2.74 1.604,1.896 false 2.104,2.75 1.781,2.75 1.781,2.75 1.781,1.896 false 0.146,0.115 0.406,0.333 0.26,0.219 10 false *a 0.406,1.635 0.823,1.844 0.417,0.208 10 false L101 0.406,0.885 1.073,1.208 0.667,0.323 10 false CANH*b 0.74,2.656 1.292,2.979 0.552,0.323 10 false CANL*b 1.823,0.865 2.49,1.188 0.667,0.323 10 false CANH*c 2.135,2.677 2.802,3 0.667,0.323 10 false CANL*c

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L101-1 (CANH) - L101-3 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L101-2 (CANH) - L101-4 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to CAN No. 5 Junction Connector)
*b to Air Conditioning Amplifier Assembly
*c to CAN No. 1 Junction Connector

Result:
Result Proceed to
OK A
NG (CAN No. 1 Junction connector main line) B
NG (ECU branch line) C




A

REPLACE CAN NO. 5 JUNCTION CONNECTOR

B

11.CHECK FOR SHORT IN SUB BUS 12 LINES (CAN NO. 1 J/C - CAN NO. 5 J/C)

C

13.CHECK FOR SHORT IN SUB BUS 12 LINES (ECUS)
11.CHECK FOR SHORT IN SUB BUS 12 LINES (CAN NO. 1 J/C - CAN NO. 5 J/C)
a.

Disconnect the wire harness connector from the CAN No. 1 junction connector (instrument panel wire side).


b.
U154805E03
1.604,1.729 1.604,0.948 1.604,0.948 1.271,0.948 false 1.854,2.708 1.604,2.708 1.604,2.708 1.604,2.094 false 0.083,0.073 0.344,0.292 0.26,0.219 10 false *a 0.417,1.677 0.833,1.885 0.417,0.208 10 false L132 0.75,0.885 1.417,1.208 0.667,0.323 10 false CANH*b 1.906,2.635 2.573,2.958 0.667,0.323 10 false CANL*b

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L132-3 (CANH) - L132-9 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to CAN No. 1 Junction Connector)
*b to CAN No. 5 Junction Connector



OK

12.CHECK FOR SHORT IN SUB BUS 12 LINES (CAN NO. 1 J/C)

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 1 J/C - CAN NO. 5 J/C)

12.CHECK FOR SHORT IN SUB BUS 12 LINES (CAN NO. 1 J/C)
a.

Disconnect the wire harness connector from the CAN No. 1 junction connector (engine room main wire side).


b.
U154806E04
1.792,1.729 1.792,0.958 1.792,0.958 2.135,0.958 false 1.792,2.115 1.792,2.719 1.792,2.719 2.135,2.719 false 1.146,0.99 1.615,0.99 1.615,0.99 1.615,1.74 false 1.135,2.708 1.604,2.708 1.604,2.708 1.604,2.083 false 0.125,0.135 0.385,0.354 0.26,0.219 10 false *a 0.427,1.667 0.844,1.875 0.417,0.208 10 false A67 2.177,0.896 2.844,1.219 0.667,0.323 10 false CANH*c 2.167,2.635 2.833,2.958 0.667,0.323 10 false CANL*c 0.583,0.896 1.25,1.219 0.667,0.323 10 false CANH*b 0.594,2.625 1.26,2.948 0.667,0.323 10 false CANL*b

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A67-3 (CANH) - A67-9 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A67-4 (CANH) - A67-10 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to CAN No. 1 Junction Connector)
*b to Brake booster with master cylinder assembly (Skid control ECU)
*c to ECM



OK

REPLACE CAN NO. 1 JUNCTION CONNECTOR

NG

13.CHECK FOR SHORT IN SUB BUS 12 LINES (ECUS)
13.CHECK FOR SHORT IN SUB BUS 12 LINES (ECUS)
a.

Reconnect all wire harness connectors (CAN No. 1 junction connector and CAN No. 5 junction connector).


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU (or sensor) to which the short circuited branch line is connected (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>TERMINALS OF ECU).


c.
U154831E03
2.417,1.917 2.167,2.448 2.167,2.448 2.031,2.448 false 2.469,1.917 2.625,2.448 2.625,2.448 2.74,2.448 false 2.396,0.896 2.688,1.156 0.292,0.26 10 false L6 0.125,0 0.479,0.354 0.354,0.354 10 false *a 1.646,2.375 2.167,2.615 0.521,0.24 10 false CA3P 2.781,2.365 3.302,2.604 0.521,0.24 10 false CA3N

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L6-31 (CA3P) - L6-30 (CA3N) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω


Text in Illustration
*a Component with harness connector
(Power Management Control ECU)

HINT:
·

If the resistance becomes normal (between 54 and 69 Ω) when the connector is disconnected from the ECU (or sensor), there may be a short in the ECU (or sensor).

·

If the resistance does not become normal (between 54 and 69 Ω) when the connector is disconnected from the ECU (or sensor), repair or replace the short circuited branch line or connector.





OK

REPLACE CORRESPONDING ECU

NG

REPAIR OR REPLACE CORRESPONDING ECU WIRE

14.CHECK FOR SHORT IN SUB BUS 12 LINE (POWER MANAGEMENT CONTROL ECU)
a.

Disconnect the power management control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

U154951E03
3.792,2.146 4.219,2.354 false 3.958,2.76 4.271,2.365 false 4.188,4.208 4.188,4.531 false 3.156,3.115 3.458,3.115 3.458,3.115 3.458,3.604 false 1.229,0.25 1.458,0.448 0.229,0.198 10 false *a 1.229,3.156 1.458,3.354 0.229,0.198 10 false *1 3.427,2.052 3.854,2.229 0.427,0.177 10 false CA3P 3.583,2.667 4.01,2.844 0.427,0.177 10 false CA3N 2.917,3.042 3.177,3.198 0.26,0.156 10 false CG 4.063,4.531 4.375,4.688 0.313,0.156 10 false BAT 4.333,0.458 4.552,0.667 0.219,0.208 12 false L6 1.833,3.844 2.146,4.052 0.313,0.208 12 false L61

Standard Resistance:
Tester Connection Condition Specified Condition Purpose Connected to
L6-31 (CA3P) - L61-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Inspection for CANH ground short CAN No. 5 junction connector
L6-30 (CA3N) - L61-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Inspection for CANL ground short
L6-31 (CA3P) - L61-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Inspection for CANH +B short
L6-30 (CA3N) - L61-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Inspection for CANL +B short


Text in Illustration
*1 DLC3 - -
*a Rear view of wire harness connector
(to Power Management Control ECU)
- -

HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 12 inspection.

·

Find the necessary inspection from the Purpose column that matches the result in the Result column from the Check Sub Bus 12 inspection.





OK

NG

15.CHECK FOR SHORT IN SUB BUS 12 LINE (CAN NO. 5 J/C - POWER MANAGEMENT CONTROL ECU)
15.CHECK FOR SHORT IN SUB BUS 12 LINE (CAN NO. 5 J/C - POWER MANAGEMENT CONTROL ECU)
a.

Disconnect the wire harness connector from the CAN No. 5 junction connector (instrument panel connector holder right side).


b.

Measure the resistance according to the value(s) in the table below.

U154832E03
3.448,3.635 3.448,3.167 3.448,3.167 3.198,3.167 false 4.198,4.177 4.198,4.51 false 3.427,1.458 3.427,0.646 3.427,0.646 3.177,0.646 false 3.979,0.604 3.729,0.604 3.729,0.604 3.729,1.448 false 1.938,2.813 2.177,3.031 0.24,0.219 10 false *1 2.125,3.885 2.573,4.125 0.448,0.24 10 false L61 2.396,1.438 2.854,1.75 0.458,0.313 10 false L102 1.927,0.177 2.167,0.396 0.24,0.219 10 false *a 4.031,0.531 4.677,0.76 0.646,0.229 10 false CANH*b 2.667,0.563 3.313,0.792 0.646,0.229 10 false CANL*b 4.073,4.521 4.479,4.792 0.406,0.271 10 false BAT 2.958,3.073 3.427,3.396 0.469,0.323 10 false CG

Standard Resistance:
Tester Connection Condition Specified Condition Purpose Connected to
L102-5 (CANH) - L61-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Inspection for CANH ground short Power management control ECU
L102-3 (CANL) - L61-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Inspection for CANL ground short
L102-5 (CANH) - L61-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Inspection for CANH +B short
L102-3 (CANL) - L61-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Inspection for CANL +B short


Text in Illustration
*1 DLC3 - -
*a Front view of wire harness connector
(to CAN No. 5 Junction Connector)
*b to Power management control ECU

HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 12 inspection.

·

Find the necessary inspection from the Purpose column that matches the result in the Result column from the Check Sub Bus 12 inspection.





OK

16.CHECK FOR SHORT IN SUB BUS 12 LINE (CAN NO. 5 J/C)

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 5 J/C - POWER MANAGEMENT CONTROL ECU)

16.CHECK FOR SHORT IN SUB BUS 12 LINE (CAN NO. 5 J/C)
a.

Disconnect the wire harness connector from the CAN No. 5 junction connector (instrument panel connector holder left side).


b.

Measure the resistance according to the value(s) in the table below.

U154833E04
3.438,3.646 3.438,3.177 3.438,3.177 3.188,3.177 false 4.167,4.188 4.167,4.521 false 3.146,1.469 3.146,0.656 3.146,0.656 2.896,0.656 false 3.427,1.469 3.427,0.656 3.427,0.656 3.677,0.656 false 3,2.313 3.292,2.313 3.292,2.313 3.292,1.594 false 3.74,2.26 3.594,2.26 3.594,2.26 3.594,1.573 false 2.01,2.854 2.25,3.073 0.24,0.219 10 false *1 2.115,3.854 2.563,4.094 0.448,0.24 10 false L61 2.396,1.438 2.854,1.75 0.458,0.313 10 false L101 1.969,0.073 2.208,0.292 0.24,0.219 10 false *a 2.354,0.563 3,0.792 0.646,0.229 10 false CANH*b 2.469,2.198 3.115,2.427 0.646,0.229 10 false CANH*c 3.708,0.583 4.354,0.813 0.646,0.229 10 false CANL*b 3.76,2.208 4.406,2.438 0.646,0.229 10 false CANL*c 4.083,4.521 4.49,4.792 0.406,0.271 10 false BAT 2.958,3.135 3.427,3.458 0.469,0.323 10 false CG

Standard Resistance:
Tester Connection Condition Specified Condition Purpose Connected to
L101-1 (CANH) - L61-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Inspection for CANH ground short Air conditioning amplifier assembly
L101-3 (CANL) - L61-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Inspection for CANL ground short
L101-2 (CANH) - L61-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Inspection for CANH ground short CAN No. 1 junction connector
L101-4 (CANL) - L61-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Inspection for CANL ground short
L101-1 (CANH) - L61-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Inspection for CANH +B short Air conditioning amplifier assembly
L101-3 (CANL) - L61-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Inspection for CANL +B short
L101-2 (CANH) - L61-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Inspection for CANH +B short CAN No. 1 junction connector
L101-4 (CANL) - L61-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Inspection for CANL +B short


Text in Illustration
*1 DLC3 - -
*a Front view of wire harness connector
(to CAN No. 5 Junction Connector)
*b to Air conditioning amplifier assembly
*c to CAN No. 1 Junction Connector - -

Result:
Result Proceed to
OK A
NG (CAN No. 1 Junction connector main line) B
NG (ECU branch line) C


HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 12 inspection.

·

Find the necessary inspection from the Purpose column that matches the result in the Result column from the Check Sub Bus 12 inspection.





A

REPLACE CAN NO. 5 JUNCTION CONNECTOR

B

17.CHECK FOR SHORT IN SUB BUS 12 LINE (CAN NO. 1 J/C - CAN NO. 5 J/C)

C

19.CHECK SUB BUS 12 LINE (ECU)
17.CHECK FOR SHORT IN SUB BUS 12 LINE (CAN NO. 1 J/C - CAN NO. 5 J/C)
a.

Disconnect the wire harness connector from the CAN No. 1 junction connector (instrument panel wire side).


b.

Measure the resistance according to the value(s) in the table below.

U154834E03
3.458,3.635 3.458,3.167 3.458,3.167 3.208,3.167 false 4.167,4.177 4.167,4.51 false 3.438,1.479 3.438,0.667 3.438,0.667 3.188,0.667 false 3.427,1.75 3.427,2.292 3.427,2.292 3.188,2.292 false 2.01,2.833 2.25,3.052 0.24,0.219 10 false *1 2.115,3.865 2.563,4.104 0.448,0.24 10 false L61 2.385,1.448 2.844,1.76 0.458,0.313 10 false L132 2.042,0.146 2.281,0.365 0.24,0.219 10 false *a 2.656,0.594 3.302,0.823 0.646,0.229 10 false CANH*b 2.656,2.219 3.302,2.448 0.646,0.229 10 false CANL*b 4.052,4.542 4.458,4.813 0.406,0.271 10 false BAT 2.99,3.104 3.458,3.427 0.469,0.323 10 false CG

Standard Resistance:
Tester Connection Condition Specified Condition Purpose Connected to
L132-3 (CANH) - L61-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Inspection for CANH ground short CAN No. 5 junction connector
L132-9 (CANL) - L61-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Inspection for CANL ground short
L132-3 (CANH) - L61-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Inspection for CANH +B short CAN No. 5 junction connector
L132-9 (CANL) - L61-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Inspection for CANL +B short


HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 12 inspection.

·

Find the necessary inspection from the Purpose column that matches the result in the Result column from the Check Sub Bus 12 inspection.



Text in Illustration
*1 DLC3 - -
*a Front view of wire harness connector
(to CAN No. 1 Junction Connector)
*b to CAN No. 5 Junction Connector



OK

18.CHECK SHORT IN SUB BUS 12 LINE (CAN NO. 1 J/C)

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 1 J/C - CAN NO. 5 J/C)

18.CHECK SHORT IN SUB BUS 12 LINE (CAN NO. 1 J/C)
a.

Disconnect the wire harness connector from the CAN No. 1 junction connector (engine room main wire side).


b.

Measure the resistance according to the value(s) in the table below.

U154835E04
3.458,3.625 3.458,3.156 3.458,3.156 3.208,3.156 false 4.167,4.188 4.167,4.521 false 3.438,1.458 3.438,0.646 3.438,0.646 3.188,0.646 false 3.563,1.479 3.563,0.667 3.563,0.667 3.813,0.667 false 3.125,2.5 3.417,2.5 3.417,2.5 3.417,1.781 false 3.719,2.479 3.573,2.479 3.573,2.479 3.573,1.792 false 2.01,2.875 2.25,3.094 0.24,0.219 10 false *1 2.104,3.865 2.552,4.104 0.448,0.24 10 false L61 2.406,1.427 2.865,1.74 0.458,0.313 10 false A67 2,0.135 2.24,0.354 0.24,0.219 10 false *a 2.656,0.583 3.302,0.813 0.646,0.229 10 false CANH*b 3.875,0.583 4.521,0.813 0.646,0.229 10 false CANH*c 2.573,2.417 3.219,2.646 0.646,0.229 10 false CANL*b 3.76,2.427 4.406,2.656 0.646,0.229 10 false CANL*c 4.042,4.51 4.448,4.781 0.406,0.271 10 false BAT 3,3.094 3.469,3.417 0.469,0.323 10 false CG

Standard Resistance:
Tester Connection Condition Specified Condition Purpose Connected to
A67-3 (CANH) - L61-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Inspection for CANH ground short Brake booster with master cylinder assembly (skid control ECU)
A67-9 (CANL) - L61-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Inspection for CANL ground short
A67-4 (CANH) - L61-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Inspection for CANH ground short ECM
A67-10 (CANL) - L61-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Inspection for CANL ground short
A67-3 (CANH) - L61-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Inspection for CANH +B short Brake booster with master cylinder assembly (skid control ECU)
A67-9 (CANL) - L61-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Inspection for CANL +B short
A67-4 (CANH) - L61-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Inspection for CANH +B short ECM
A67-10 (CANL) - L61-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Inspection for CANL +B short


Text in Illustration
*1 DLC3 - -
*a Front view of wire harness connector
(to CAN No. 1 Junction Connector)
*b to Brake booster with master cylinder assembly (Skid control ECU)
*c to ECM - -

HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 12 inspection.

·

Find the necessary inspection from the Purpose column that matches the result in the Result column from the Check Sub Bus 12 inspection.





OK

REPLACE CAN NO. 1 JUNCTION CONNECTOR

NG

19.CHECK SUB BUS 12 LINE (ECU)
19.CHECK SUB BUS 12 LINE (ECU)
a.

Reconnect all wire harness connectors (CAN No. 1 junction connector and CAN No. 5 junction connector).


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU to which the bus line shorted to +B or shorted to GND is connected.


c.
U154830E05
2.427,1.688 2.115,1.042 2.115,1.042 1.875,1.042 false 2.635,1.698 2.885,1.01 2.885,1.01 3.042,1.01 false 2.427,1.906 2.177,2.438 2.177,2.438 2.042,2.438 false 2.469,1.906 2.625,2.438 2.625,2.438 2.74,2.438 false 2.406,0.885 2.698,1.146 0.292,0.26 10 false L6 0.125,0.063 0.479,0.417 0.354,0.354 10 false *a 1.615,2.344 2.135,2.583 0.521,0.24 10 false CA3P 2.792,2.344 3.313,2.583 0.521,0.24 10 false CA3N 1.406,0.969 1.927,1.208 0.521,0.24 10 false AM21 3.073,0.927 3.365,1.167 0.292,0.24 10 false E12

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Purpose
L6-31 (CA3P) - L6-4 (E12) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω:
CANH ground short
L6-30 (CA3N) - L6-4 (E12) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω:
CANL ground short
L6-31 (CA3P) - L6-7 (AM21) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ:
CANH +B short
L6-30 (CA3N) - L6-7 (AM21) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ:
CANL +B short


Text in Illustration
*a Component with harness connector
(Power Management Control ECU)

HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 12 inspection.

·

Find the necessary inspection from the Purpose column that matches the result in the Result column from the Check Sub Bus 12 inspection.





OK

REPLACE CORRESPONDING ECU

NG

REPAIR OR REPLACE CORRESPONDING ECU WIRE