Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU) › 2014.11–2016.05
RM2070E _57 Power Source / Network _061936 NETWORKING _0301754 CAN COMMUNICATION SYSTEM(w/o Central Gateway ECU) C

NETWORKING  CAN COMMUNICATION SYSTEM(w/o Central Gateway ECU)  U110B  Lost Communication with Parking Assist Control Module "B"  


DESCRIPTION

DTC No. DTC Detection Condition Trouble Area
U110B No communication from the parking assist ECU continues.
·

Parking assist ECU branch line or connector

·

Power source circuit of parking assist ECU

·

Parking assist ECU ground circuit

·

Parking assist ECU



HINT:

This diagnosis procedure is for when DTC U110B is output by the power management control ECU (GTS display: PM1 Gateway).


WIRING DIAGRAM

C317122E03
2.479,0.76 2.479,0.271 2.479,0.271 2.729,0.271 false 2.792,0.198 4.833,0.438 2.042,0.24 10 false CAN No. 4 Junction Connector 0.271,2.302 1.521,2.75 1.25,0.448 10 false Power Management Control ECU 5.813,2.323 7.021,2.688 1.208,0.365 10 false CAN No. 1 Junction Terminal 3.354,4.094 5.208,4.354 1.854,0.26 10 false Parking Assist ECU 3.417,4.625 4.375,4.948 0.958,0.323 10 false Trouble Area 4.406,5.01 6.26,5.208 1.854,0.198 10 false : CAN Branch Line (CANH) 1.448,5.417 3.385,5.677 1.938,0.26 10 false : CAN Main Bus Line (CANL) 1.448,5.01 3.365,5.271 1.917,0.26 10 false : CAN Main Bus Line (CANH) 4.427,5.427 6.375,5.729 1.948,0.302 10 false : CAN Branch Line (CANL) 3.333,2.948 3.75,3.229 0.417,0.281 10 false +B 4.052,2.76 4.469,3.042 0.417,0.281 10 false CANL 3.594,2.76 4.01,3.042 0.417,0.281 10 false CANH 3.333,3.396 3.75,3.677 0.417,0.281 10 false IG 4.323,3.323 4.74,3.604 0.417,0.281 10 false GND1 3.323,3.833 3.74,4.115 0.417,0.281 10 false ACC 3.688,2.552 4.104,2.833 0.417,0.281 10 false L65 4.083,2.563 4.5,2.844 0.417,0.281 10 false L65 2.99,2.948 3.406,3.229 0.417,0.281 10 false L64 2.979,3.375 3.396,3.656 0.417,0.281 10 false L64 2.979,3.823 3.396,4.104 0.417,0.281 10 false L64 4.771,3.313 5.188,3.594 0.417,0.281 10 false L64 4.844,3.135 5.26,3.417 0.417,0.281 10 false 4 4.406,2.552 4.823,2.833 0.417,0.281 10 false 39 3.438,2.552 3.854,2.833 0.417,0.281 10 false 40 3.052,2.76 3.469,3.042 0.417,0.281 10 false 1 3.052,3.208 3.469,3.49 0.417,0.281 10 false 8 3.052,3.646 3.469,3.927 0.417,0.281 10 false 9 2.167,3.104 2.833,3.354 0.667,0.25 10 false RAD NO.1 2.156,3.542 3.031,3.813 0.875,0.271 10 false ECU-IG NO.2 2.167,3.979 3.042,4.25 0.875,0.271 10 false ECU-ACC 6.115,1.667 6.604,1.896 0.49,0.229 10 false 120 Ω 0.667,1.677 1.156,1.906 0.49,0.229 10 false 120 Ω 0.135,0.073 1.385,0.521 1.25,0.448 12 false Sub Bus 11:

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the power switch on (IG) and wait at least 60 seconds.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>DIAGNOSIS SYSTEM).

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.RECONFIRM DTC OUTPUT
a.

Reconfirm DTCs.

HINT:

If DTC U1002 is output from PM1 Gateway of the power management control ECU, this indicates a sub bus 11 malfunction. Troubleshoot for DTC U1002 and check for malfunctions in sub bus 11.


Result:
Result Proceed to
U1002 is not output from the power management control ECU (GTS display: PM1 Gateway) A
U1002 is output from power the management control ECU (GTS display: PM1 Gateway) B




A

2.CHECK FOR OPEN IN SUB BUS 11 LINES (PARKING ASSIST ECU BRANCH LINE)

B

GO TO DIAGNOSIS PROCEDURE INDICATED BY OUTPUT DTC

2.CHECK FOR OPEN IN SUB BUS 11 LINES (PARKING ASSIST ECU BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
U191299E01
2.168,0.214 2.432,0.395 0.264,0.181 10 L65 0.123,0.097 0.288,0.244 0.165,0.147 10 *a 2.882,0.642 3.313,0.788 0.431,0.147 10 CANH 1.848,1.881 2.305,2.028 0.457,0.147 10 CANL 2.345,1.97 2.422,1.97 2.422,1.97 2.599,1.469 false 2.858,0.74 2.803,0.74 2.803,0.74 2.721,1.406 false

Disconnect the L65 parking assist ECU connector.

Text in Illustration
*a Front view of wire harness connector
(to Parking Assist ECU)


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L65-40 (CANH) - L65-39 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω




OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (PARKING ASSIST ECU)

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Disconnect the L64 parking assist ECU connector.


b.
U190999E01
1.521,2.86 1.858,3.016 0.336,0.156 10 ACC 0.272,0.754 0.498,0.910 0.225,0.156 10 +B 0.092,0.054 0.318,0.210 0.225,0.156 10 *a 2.784,0.864 3.211,1.020 0.427,0.156 10 GND1 1.532,1.175 1.848,1.331 0.316,0.156 10 L64 2.759,0.945 2.694,0.945 2.694,0.945 2.638,1.902 false 0.53,0.84 0.613,0.84 0.613,0.84 0.854,1.902 false 1.34,2.285 1.21,2.837 false 1.089,2.868 1.264,3.024 0.174,0.156 10 IG 1.49,2.288 1.673,2.835 false

Measure the resistance according to the value(s) in the table below.

Text in Illustration
*a Front view of wire harness connector
(to Parking Assist ECU)

Standard Resistance:
Tester Connection Condition Specified Condition
L64-4 (GND1) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



c.

Reconnect the cable to the negative (-) auxiliary battery terminal.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L64-1 (+B) - Body ground Power switch off 11 to 14 V
L64-9 (ACC) - Body ground Power switch on (ACC) 11 to 14 V
L64-8 (IG) - Body ground Power switch on (IG) 11 to 14 V




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)