Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU) › 2015.08–2016.05
RM2070E _57 Power Source / Network _061936 NETWORKING _0301754 CAN COMMUNICATION SYSTEM(w/o Central Gateway ECU) C

NETWORKING  CAN COMMUNICATION SYSTEM(w/o Central Gateway ECU)  U1002  Lost Communication with Gateway Module (Power Management1)  


DESCRIPTION

·

The power management control ECU will store this DTC when no signals can be received from the ECUs that have been memorized as those that are connected to sub bus 11.

·

When the power management control ECU receives a response signal from the ECUs connected to sub bus 11, the power management control ECU recognizes and memorizes that the ECU is connected to sub bus 11. Based on this memorized data, the power management control ECU monitors for malfunctions in the ECUs connected to sub bus 11 when communicating with those ECUs. If the power management control ECU cannot receive response signals from the ECUs that have been memorized as those connected to sub bus 11, the power management control ECU determines that a malfunction exists.


DTC No. DTC Detection Condition Trouble Area
U1002 Power management control ECU cannot receive signals from all ECUs that have been memorized as those connected to sub bus 11.
·

Open or short in sub bus 11 main line or connector

·

Open or short in sub bus 11 branch line or connector

·

Power management control ECU

·

Driving support ECU assembly*1

·

Parking assist ECU*2

·

Lane departure warning camera*3

·

CAN No. 4 junction connector

·

CAN No. 1 junction terminal



*1: w/ Pre-crash Safety System

*2: w/ Intelligent Parking Assist System

*3: w/ Lane Departure Alert System

HINT:

This diagnosis procedure is for when DTC U1002 is output by the power management control ECU (GTS display: PM1 Gateway).


WIRING DIAGRAM

C316698E02
5.083,0.698 6.458,0.896 1.375,0.198 10 false x: Suspected Area 1.26,0.854 2.5,1.365 1.24,0.51 10 false Power Management Control ECU 3.323,0.875 3.833,1.073 0.51,0.198 10 false 120 Ω 3.323,7.281 3.833,7.479 0.51,0.198 10 false 120 Ω 0.979,0.865 1.313,1.063 0.333,0.198 10 false L5 3.75,2.396 4.083,2.594 0.333,0.198 10 false L184 4.281,2.927 4.615,3.125 0.333,0.198 10 false L182 4.281,3.292 4.615,3.49 0.333,0.198 10 false L182 5.76,3.677 7.01,4.198 1.25,0.521 10 false Driving Support ECU Assembly*1 2.479,4.063 2.813,4.26 0.333,0.198 10 false L185 2.479,4.427 2.813,4.625 0.333,0.198 10 false L185 4.281,4.906 4.615,5.104 0.333,0.198 10 false L183 4.281,5.271 4.615,5.469 0.333,0.198 10 false L183 0.365,4.844 2.708,5.406 2.344,0.563 10 false Lane Departure Warning Camera*2 5.667,5.656 7.052,6.354 1.385,0.698 10 false Parking Assist ECU*3 3,5.719 3.333,5.917 0.333,0.198 10 false L181 3.75,5.719 4.083,5.917 0.333,0.198 10 false L181 4.5,6.969 4.948,7.167 0.448,0.198 10 false L180 4.875,6.969 6.917,7.448 2.042,0.479 10 false CAN No. 1 Junction Terminal 2.771,1.448 3.281,1.646 0.51,0.198 10 false CA2L 4,1.427 4.51,1.625 0.51,0.198 10 false CA2H 2.906,1.979 3.417,2.177 0.51,0.198 10 false G 3.969,1.656 4.479,1.854 0.51,0.198 10 false 34 2.99,2.396 3.323,2.594 0.333,0.198 10 false L184 2.938,1.656 3.271,1.854 0.333,0.198 10 false 35 4.031,1.979 4.542,2.177 0.51,0.198 10 false B 5.146,2.729 5.656,2.927 0.51,0.198 10 false B 1.917,3.906 2.427,4.104 0.51,0.198 10 false B 5.146,4.708 5.656,4.906 0.51,0.198 10 false B 4.031,6.177 4.542,6.375 0.51,0.198 10 false B 2.927,6.188 3.438,6.385 0.51,0.198 10 false Y 5.156,5.5 5.667,5.698 0.51,0.198 10 false L 5.458,3.677 5.802,3.906 0.344,0.229 10 false L60 1.917,4.667 2.427,4.865 0.51,0.198 10 false W 5.375,5.656 5.719,5.885 0.344,0.229 10 false L65 0.073,4.844 0.604,5.115 0.531,0.271 10 false U13 4.156,2.396 4.667,2.594 0.51,0.198 10 false 1 4.396,2.74 4.635,2.927 0.24,0.188 10 false 1 4.396,4.74 4.635,4.927 0.24,0.188 10 false 1 2.604,3.885 2.844,4.073 0.24,0.188 10 false 1 4.156,5.75 4.396,5.938 0.24,0.188 10 false 1 2.813,2.417 3.323,2.615 0.51,0.198 10 false 2 2.594,4.635 3.104,4.833 0.51,0.198 10 false 2 4.385,3.51 4.896,3.708 0.51,0.198 10 false 2 4.396,5.479 4.906,5.677 0.51,0.198 10 false 2 2.823,5.74 3.333,5.938 0.51,0.198 10 false 2 0.167,2.208 2.823,3.167 2.656,0.958 10 false *1: w/ Pre-crash Safety System 0.927,8.021 2.917,8.313 1.99,0.292 10 false : CAN Main Bus Line (CANH) 0.948,8.417 2.875,8.698 1.927,0.281 10 false : CAN Main Bus Line (CANL) 3.906,8 5.688,8.26 1.781,0.26 10 false : CAN Branch Line (CANH) 3.927,8.417 5.802,8.698 1.875,0.281 10 false : CAN Branch Line (CANL) 2.708,6.688 3.188,6.917 0.479,0.229 10 false CANL 3.969,6.698 4.448,6.927 0.479,0.229 10 false CANH 3.021,6.479 3.313,6.708 0.292,0.229 10 false 2 3.979,6.469 4.271,6.698 0.292,0.229 10 false 3 5.135,3.5 5.646,3.698 0.51,0.198 10 false R 5.854,2.833 6.365,3.031 0.51,0.198 10 false CA2H 0.979,4 1.49,4.198 0.51,0.198 10 false CA1P 0.969,4.552 1.479,4.75 0.51,0.198 10 false CA1N 1.427,4 1.938,4.198 0.51,0.198 10 false 6 1.417,4.552 1.927,4.75 0.51,0.198 10 false 12 5.854,4.823 6.365,5.021 0.51,0.198 10 false CANH 5.865,5.385 6.375,5.583 0.51,0.198 10 false CANL 5.635,4.823 6.146,5.021 0.51,0.198 10 false 40 5.635,5.396 6.146,5.594 0.51,0.198 10 false 39 5.615,2.833 6.125,3.031 0.51,0.198 10 false 39 5.625,3.396 6.135,3.594 0.51,0.198 10 false 17 5.865,3.396 6.375,3.594 0.51,0.198 10 false CA2L 0.729,5.438 2.854,5.823 2.125,0.385 10 false CAN No. 4 Junction Connector 0.229,0.177 2,0.74 1.771,0.563 12 false Sub Bus 11: 0.167,2.635 2.823,3.594 2.656,0.958 10 false *2: w/ Lane Departure Alert System 0.167,3.083 2.823,4.042 2.656,0.958 10 false *3: w/ Intelligent Parking Assist System

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the power switch on (IG), wait at least 20 seconds, and then drive the vehicle at a speed of 50 km/h (31 mph) or more at least 1.72 seconds.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>DIAGNOSIS SYSTEM).



HINT:
·

Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.

·

Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wire harnesses, and to make future maintenance easier.



PROCEDURE

1.CHECK SUB BUS 11
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
U154820E03
1.813,1.688 1.604,1.135 1.604,1.135 1.458,1.135 false 1.813,1.906 1.365,2.458 false 1.865,1.906 2.01,2.469 false 2.24,1.698 2.75,2.396 false 0.063,0.042 0.333,0.26 0.271,0.219 10 false *a 1.99,0.896 2.26,1.115 0.271,0.219 10 false L5 1.813,2.458 2.344,2.667 0.531,0.208 10 false CA2H 1.115,2.469 1.646,2.677 0.531,0.208 10 false CA2L 1.25,1.052 1.479,1.26 0.229,0.208 10 false E1 2.531,2.427 3.063,2.635 0.531,0.208 10 false AM22

Measure the resistance according to the value(s) in the table below.

Text in Illustration
*a Component with harness connected
(Power Management Control ECU)

Standard Resistance:
Tester Connection Condition Specified Condition Result
L5-34 (CA2H) - L5-35 (CA2L) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω Below 54 Ω: Short circuit between bus lines
70 Ω or higher: Open circuit in main bus lines
L5-34 (CA2H) - L5-6 (E1) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANH ground short
L5-35 (CA2L) - L5-6 (E1) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
L5-34 (CA2H) - L5-1 (AM22) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short
L5-35 (CA2L) - L5-1 (AM22) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short



Result:
Result Proceed to
OK A
NG (Open circuit in CAN main bus line) B
NG (Short circuit between bus lines) C
·

NG (Ground short)

·

NG (+B short)


D



A

2.CHECK FOR DTC OUTPUT

B

3.CHECK FOR OPEN IN SUB BUS 11 MAIN LINES (POWER MANAGEMENT CONTROL ECU)

C

6.CHECK FOR SHORT IN SUB BUS 11 LINES (POWER MANAGEMENT CONTROL ECU)

D

12.CHECK FOR SHORT IN SUB BUS 11 BUS LINE (POWER MANAGEMENT CONTROL ECU)
2.CHECK FOR DTC OUTPUT
a.

Reconnect the cable to the negative (-) auxiliary battery terminal.


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG).


d.

Turn the GTS on.


e.

Clear the DTCs.


f.

Turn the power switch off.


g.

Turn the power switch on (IG).


h.

Check for DTCs.

Result:
Result Proceed to
DTC U1002 is output from the power management control ECU (GTS display: PM1 Gateway) A
DTC U1002 is not output from the power management control ECU (GTS display: PM1 Gateway) B




A

B

3.CHECK FOR OPEN IN SUB BUS 11 MAIN LINES (POWER MANAGEMENT CONTROL ECU)
a.
U154242E03
1.823,2.583 1.458,2.646 false 1.865,2.573 1.573,3.031 false 2.042,0.615 2.25,0.792 0.208,0.177 10 false L5 1.115,2.583 1.479,2.76 0.365,0.177 10 false CA2L 1.292,3.052 1.677,3.229 0.385,0.177 10 false CA2H 0.146,0.083 0.719,0.448 0.573,0.365 10 false *a

Disconnect the L5 power management control ECU connector.

Text in Illustration
*a Rear view of wire harness connector
(to Power Management Control ECU)


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L5-34 (CA2H) - L5-35 (CA2L) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω




OK

NG

4.CHECK CHECK FOR OPEN IN SUB BUS 11 MAIN LINES (CAN NO. 1 JUNCTION TERMINAL)
4.CHECK CHECK FOR OPEN IN SUB BUS 11 MAIN LINES (CAN NO. 1 JUNCTION TERMINAL)
a.

Reconnect the L5 power management control ECU connector.


b.
U190995E02
0.938,0.823 0.635,0.823 0.635,0.823 0.635,2.156 false 1.229,1.167 0.927,1.167 0.927,1.167 0.927,2.156 false 0.177,0.094 0.333,0.271 0.156,0.177 10 false *a 0.99,0.74 1.563,0.896 0.573,0.156 10 false CANH 1.281,1.073 1.844,1.229 0.563,0.156 10 false CANL 1.823,2.146 2.208,2.313 0.385,0.167 10 false L180

Disconnect the L180 CAN No. 1 junction terminal.

Text in Illustration
*a Rear view of wire harness connector
(to CAN No. 1 Junction Terminal)


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L180-3 (CANH) - L180-2 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω




OK

REPLACE CAN NO. 1 JUNCTION TERMINAL

NG

5.CHECK FOR OPEN IN SUB BUS 11 MAIN LINES (CAN NO. 4 JUNCTION CONNECTOR)
5.CHECK FOR OPEN IN SUB BUS 11 MAIN LINES (CAN NO. 4 JUNCTION CONNECTOR)
a.

Reconnect the L180 CAN No. 1 junction terminal.


b.
U191178E02
0.844,2.313 0.573,2.302 false 2.24,2.406 2.396,2.667 2.396,2.667 2.396,2.865 false 0.948,2.385 1.104,2.646 1.104,2.646 1.104,2.844 false 2.188,2.271 1.948,1.854 1.948,1.854 1.781,1.854 false 2.656,2.229 2.406,2.229 false 1.094,2.219 1.333,2.219 false 2.396,2.375 2.552,2.625 2.552,2.625 2.656,2.625 false 1.083,2.396 1.24,2.646 1.24,2.646 1.344,2.646 false 1.354,2.146 1.979,2.344 0.625,0.198 10 false CANH*b 2.698,2.125 3.302,2.323 0.604,0.198 10 false CANH*c 1.375,2.563 1.958,2.76 0.583,0.198 10 false CANL*b 2.698,2.542 3.271,2.74 0.573,0.198 10 false CANL*c 0.438,2.229 0.625,2.448 0.188,0.219 10 false B 1.063,2.844 1.271,3.031 0.208,0.188 10 false G 1.656,1.781 1.813,1.958 0.156,0.177 10 false B 2.354,2.885 2.563,3.094 0.208,0.208 10 false Y 0.083,0.115 0.333,0.344 0.25,0.229 10 false *a 0.927,1.677 1.375,1.927 0.448,0.25 10 false L184 2.219,1.698 2.646,1.927 0.427,0.229 10 false L181

Disconnect the L181 and L184 CAN No. 4 junction connectors.

Text in Illustration
*a Rear view of wire harness connector
(to CAN No. 4 Junction Connector)
*b to Power Management Control ECU
*c to CAN No. 1 Junction Terminal


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
L184-1 (CANH) - L184-2 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω Power management control ECU
L181-1 (CANH) - L181-2 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω CAN No. 1 junction terminal


Wiring Color
Code Color (CANH Side) Color (CANL Side) Connected to
L184 B G Power management control ECU
L181 B Y CAN No. 1 junction terminal

NOTICE:
·

Before disconnecting the connector, make a note of where it is connected.

·

Reconnect the connector to its original position.



Result:
Result Proceed to
OK A
NG (Power management control ECU main line) B
NG (CAN No. 1 junction terminal main line) C




A

REPLACE CAN NO. 4 JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (CAN NO. 4 JUNCTION CONNECTOR - POWER MANAGEMENT CONTROL ECU)

C

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (CAN NO. 4 JUNCTION CONNECTOR - CAN NO. 1 JUNCTION TERMINAL)

6.CHECK FOR SHORT IN SUB BUS 11 LINES (POWER MANAGEMENT CONTROL ECU)
a.
U154243E03
1.813,2.573 1.448,2.635 false 1.865,2.573 1.573,3.031 false 2.042,0.604 2.25,0.781 0.208,0.177 10 false L5 1.125,2.563 1.49,2.74 0.365,0.177 10 false CA2L 1.323,3.042 1.708,3.219 0.385,0.177 10 false CA2H 0.146,0.083 0.719,0.448 0.573,0.365 10 false *a

Disconnect the L5 power management control ECU connector.

Text in Illustration
*a Rear view of wire harness connector
(to Power Management Control ECU)


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L5-34 (CA2H) - L5-35 (CA2L) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω




OK

NG

7.CHECK FOR SHORT IN SUB BUS 11 LINES (POWER MANAGEMENT CONTROL ECU - CAN NO. 4 JUNCTION CONNECTOR)
7.CHECK FOR SHORT IN SUB BUS 11 LINES (POWER MANAGEMENT CONTROL ECU - CAN NO. 4 JUNCTION CONNECTOR)
a.

Reconnect the L5 power management control ECU connector.


b.
U191179E02
0.833,2.323 0.563,2.323 false 0.948,2.396 1.104,2.646 1.104,2.646 1.104,2.844 false 1.094,2.229 1.333,2.229 false 1.104,2.375 1.26,2.635 1.26,2.635 1.365,2.635 false 1.365,2.146 1.99,2.344 0.625,0.198 10 false CANH*b 1.396,2.552 1.979,2.75 0.583,0.198 10 false CANL*b 0.448,2.24 0.635,2.458 0.188,0.219 10 false B 1.063,2.854 1.271,3.042 0.208,0.188 10 false G 0.083,0.01 0.333,0.24 0.25,0.229 10 false *a 0.896,1.698 1.292,1.948 0.396,0.25 10 false L184

Disconnect the L184 CAN No. 4 junction connector.

Text in Illustration
*a Rear view of wire harness connector
(to CAN No. 4 Junction Connector)
*b to Power Management Control ECU


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
L184-1 (CANH) - L184-2 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω Power management control ECU


Wiring Color
Code Color (CANH Side) Color (CANL Side) Connected to
L184 B G Power management control ECU

NOTICE:
·

Before disconnecting the connector, make a note of where it is connected.

·

Reconnect the connector to its original position.





OK

8.CHECK FOR SHORT IN SUB BUS 11 LINES (BRANCH LINE)

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (CAN NO. 4 JUNCTION CONNECTOR - POWER MANAGEMENT CONTROL ECU)

8.CHECK FOR SHORT IN SUB BUS 11 LINES (BRANCH LINE)
a.

Reconnect the L184 CAN No. 4 junction connector.


b.
U191180E02
1.052,0.802 1.354,0.802 1.354,0.802 1.844,1.438 false 1.844,1.688 1.844,2.656 1.844,2.656 1.958,2.656 false 0.656,0.719 1.281,0.917 0.625,0.198 10 false CANH 2.01,2.573 2.594,2.771 0.583,0.198 10 false CANL 0.125,0.167 0.375,0.396 0.25,0.229 10 false *a 1.729,0.76 2.177,1.01 0.448,0.25 10 false L184

Connect the probes of an ohmmeter to terminals 1 (CANH) and 2 (CANL) of the power management control ECU main line harness connector.

Text in Illustration
*a Component with harness connector
(CAN No. 4 Junction Connector)


c.

While observing the resistance value shown on the ohmmeter, disconnect branch line connectors (L182, L183 and L185) from the CAN No. 4 junction connector until the resistance becomes normal (between 54 and 69 Ω).

C316884E05
3.563,2.844 3.948,3.063 0.385,0.219 10 false L183 2.344,0.438 2.594,0.667 0.25,0.229 10 false *a 3.573,2.573 4,2.802 0.427,0.229 10 false L182 3.563,3.417 3.99,3.646 0.427,0.229 10 false L185 3.563,3.125 3.99,3.354 0.427,0.229 10 false L184 3.563,2.302 3.99,2.531 0.427,0.229 10 false L181

Text in Illustration
*a CAN No. 4 Junction Connector - -

Wiring Color
CAN No. 4 Junction Connector Side Code Color (CANH Side) Color (CANL Side)
CAN main bus line (bus line connecting CAN No. 4 junction connector and CAN No. 1 junction terminal) L181 B Y
Driving support ECU assembly*1 L182 B R
Parking assist ECU*2 L183 B L
CAN main bus line (bus line connecting power management control ECU and CAN No. 1 junction terminal) L184 B G
Lane departure warning camera*3 L185 B W

*1: w/ Pre-crash Safety System

*2: w/ Intelligent Parking Assist System

*3: w/ Lane Departure Alert System


CAUTION:

Do not reconnect the disconnected connectors until this inspection is complete because there may be a short in 2 or more branch lines.


Result:
Result Proceed to
The resistance is still below 54 Ω when all the specified connectors are disconnected.
(There are no shorts between a pair of branch lines.)
A
The resistance becomes normal (between 54 and 69 Ω) when a connector is disconnected.
(There is a short between one or more pairs of branch lines.)
B



d.

When there is a short in one or more of the branch lines:

i.

Reconnect all of the connectors to the CAN junction connector, except for the one that was disconnected last (the short-circuited bus line). Check that the resistance shown on the tester is normal (between 54 and 69 Ω) to confirm that there is a short in the one branch line only.

HINT:
·

Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines.

·

Reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wire such as tension on the wire harnesses, and to make future maintenance easier.






A

9.CHECK FOR SHORT IN SUB BUS 11 LINES (CAN NO. 4 JUNCTION CONNECTOR)

B

11.CHECK FOR SHORT IN SUB BUS 11 LINES (ECU, SENSOR)
9.CHECK FOR SHORT IN SUB BUS 11 LINES (CAN NO. 4 JUNCTION CONNECTOR)
a.

Disconnect the L181 CAN No. 4 junction connector.


b.
U191181E02
1.052,0.802 1.354,0.802 1.354,0.802 1.844,1.438 false 1.854,1.677 1.854,2.646 1.854,2.646 1.969,2.646 false 0.635,0.719 1.26,0.917 0.625,0.198 10 false CANH 2.021,2.563 2.604,2.76 0.583,0.198 10 false CANL 0.146,0.156 0.396,0.385 0.25,0.229 10 false *a 1.74,0.76 2.188,1.01 0.448,0.25 10 false L184

Measure the resistance according to the value(s) in the table below.

Text in Illustration
*a Component with harness connector
(CAN No. 4 Junction Connector)

Standard Resistance:
Tester Connection Condition Specified Condition
L184-1 (CANH) - L184-2 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


NOTICE:
·

Before disconnecting the connector, make a note of where it is connected.

·

Reconnect the connector to its original position.





OK

10.CHECK FOR SHORT IN SUB BUS 11 LINES (CAN NO. 1 JUNCTION TERMINAL)

NG

REPLACE CAN NO. 4 JUNCTION CONNECTOR

10.CHECK FOR SHORT IN SUB BUS 11 LINES (CAN NO. 1 JUNCTION TERMINAL)
a.

Reconnect the L181 CAN No. 4 junction connector.


b.
U190995E02
0.938,0.823 0.635,0.823 0.635,0.823 0.635,2.156 false 1.229,1.167 0.927,1.167 0.927,1.167 0.927,2.156 false 0.177,0.094 0.333,0.271 0.156,0.177 10 false *a 0.99,0.74 1.563,0.896 0.573,0.156 10 false CANH 1.281,1.073 1.844,1.229 0.563,0.156 10 false CANL 1.823,2.146 2.208,2.313 0.385,0.167 10 false L180

Disconnect the L180 CAN No. 1 junction terminal.

Text in Illustration
*a Rear view of wire harness connector
(to CAN No. 1 Junction Terminal)


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L180-3 (CANH) - L180-2 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω




OK

REPLACE CAN NO. 1 JUNCTION TERMINAL

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (CAN NO. 4 JUNCTION CONNECTOR - CAN NO. 1 JUNCTION TERMINAL)

11.CHECK FOR SHORT IN SUB BUS 11 LINES (ECU, SENSOR)
a.

Reconnect the connector for the short-circuited branch line to the CAN junction connector (the connector that caused the bus line resistance to become normal (between 54 and 69 Ω) when it was disconnected).


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU to which the short-circuited branch line is connected (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>TERMINALS OF ECU).


c.
U154821E03
1.802,1.906 1.354,2.458 false 1.865,1.906 2.01,2.469 false 0.063,0 0.333,0.219 0.271,0.219 10 false *a 1.99,0.896 2.26,1.115 0.271,0.219 10 false L5 1.813,2.479 2.344,2.688 0.531,0.208 10 false CA2H 1.115,2.458 1.646,2.667 0.531,0.208 10 false CA2L

Measure the resistance according to the value(s) in the table below.

Text in Illustration
*a Component with harness connector
(Power Management Control ECU)

Standard Resistance:
Tester Connection Condition Specified Condition
L5-34 (CA2H) - L5-35 (CA2L) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω


HINT:

If the resistance changes to normal when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.




OK

REPLACE CORRESPONDING ECU OR SENSOR

NG

REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR BRANCH LINES OR CONNECTOR

12.CHECK FOR SHORT IN SUB BUS 11 BUS LINE (POWER MANAGEMENT CONTROL ECU)
a.
U154244E03
1.813,2.583 1.448,2.646 false 1.865,2.573 1.573,3.031 false 2.24,2.354 2.573,2.188 false 1.823,2.354 1.656,2.135 false 2.073,3.042 2.281,3.219 0.208,0.177 10 false L5 1.104,2.583 1.469,2.76 0.365,0.177 10 false CA2L 1.333,3.052 1.719,3.229 0.385,0.177 10 false CA2H 0.146,0.052 0.844,0.385 0.698,0.333 10 false *a 2.625,2.083 3,2.26 0.375,0.177 10 false AM22 1.479,2.052 1.667,2.229 0.188,0.177 10 false E1

Disconnect the L5 power management control ECU connector.

Text in Illustration
*a Rear view of wire harness connector
(to Power Management Control ECU)


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Result
L5-34 (CA2H) - L5-6 (E1) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANH ground short
L5-35 (CA2L) - L5-6 (E1) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
L5-34 (CA2H) - L5-1 (AM22) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short
L5-35 (CA2L) - L5-1 (AM22) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short


HINT:

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 11 inspection.

Find the necessary inspection from the Result column that matches the result in the Result column from the Check Sub Bus 11 inspection.




OK

NG

13.CHECK FOR SHORT IN SUB BUS 11 LINE (CAN NO. 4 JUNCTION CONNECTOR - POWER MANAGEMENT CONTROL ECU)
13.CHECK FOR SHORT IN SUB BUS 11 LINE (CAN NO. 4 JUNCTION CONNECTOR - POWER MANAGEMENT CONTROL ECU)
a.
U191179E02
0.833,2.323 0.563,2.323 false 0.948,2.396 1.104,2.646 1.104,2.646 1.104,2.844 false 1.094,2.229 1.333,2.229 false 1.104,2.375 1.26,2.635 1.26,2.635 1.365,2.635 false 1.365,2.146 1.99,2.344 0.625,0.198 10 false CANH*b 1.396,2.552 1.979,2.75 0.583,0.198 10 false CANL*b 0.448,2.24 0.635,2.458 0.188,0.219 10 false B 1.063,2.854 1.271,3.042 0.208,0.188 10 false G 0.083,0.01 0.333,0.24 0.25,0.229 10 false *a 0.896,1.698 1.292,1.948 0.396,0.25 10 false L184

Disconnect the L184 CAN No. 4 junction connector.

Text in Illustration
*a Rear view of wire harness connector
(to CAN No. 4 Junction Connector)
*b to Power Management Control ECU

NOTICE:
·

Before disconnecting the connector, make a note of where it is connected.

·

Reconnect the connector to its original position.




b.
U154245E04
1.823,2.573 1.458,2.635 false 1.865,2.573 1.573,3.031 false 2.25,2.365 2.583,2.198 false 1.823,2.365 1.656,2.146 false 2.063,3.052 2.271,3.229 0.208,0.177 10 false L5 1.031,2.583 1.396,2.76 0.365,0.177 10 false CA2L 1.115,3.021 1.5,3.198 0.385,0.177 10 false CA2H 0.146,0.052 0.844,0.385 0.698,0.333 10 false *a 2.625,2.083 3.125,2.333 0.5,0.25 10 false AM22 1.448,2.042 1.635,2.219 0.188,0.177 10 false E1

Measure the resistance according to the value(s) in the table below.

Text in Illustration
*a Rear view of wire harness connector
(to Power Management Control ECU)

Standard Resistance:
Tester Connection Condition Specified Condition Result
L5-34 (CA2H) - L5-6 (E1) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANH ground short
L5-35 (CA2L) - L5-6 (E1) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
L5-34 (CA2H) - L5-1 (AM22) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short
L5-35 (CA2L) - L5-1 (AM22) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short


HINT:

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 11 inspection.

Find the necessary inspection from the Result column that matches the result in the Result column from the Check Sub Bus 11 inspection.




OK

14.CHECK FOR SHORT IN SUB BUS 11 LINE (BRANCH LINE)

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 4 JUNCTION CONNECTOR - POWER MANAGEMENT CONTROL ECU)

14.CHECK FOR SHORT IN SUB BUS 11 LINE (BRANCH LINE)
a.

Reconnect the L184 CAN No. 4 junction connector.


b.
U154245E04
1.823,2.573 1.458,2.635 false 1.865,2.573 1.573,3.031 false 2.25,2.365 2.583,2.198 false 1.823,2.365 1.656,2.146 false 2.063,3.052 2.271,3.229 0.208,0.177 10 false L5 1.031,2.583 1.396,2.76 0.365,0.177 10 false CA2L 1.115,3.021 1.5,3.198 0.385,0.177 10 false CA2H 0.146,0.052 0.844,0.385 0.698,0.333 10 false *a 2.625,2.083 3.125,2.333 0.5,0.25 10 false AM22 1.448,2.042 1.635,2.219 0.188,0.177 10 false E1

Connect the probes of an ohmmeter to terminals CANH or CANL and GND (E1) or +B (AM22) of the power management control ECU.

Text in Illustration
*a Rear view of wire harness connector
(to Power Management Control ECU)

HINT:
·

It is only necessary to perform the inspection for the result (short circuit) that was obtained in the Check Sub Bus 11 Line inspection.

·

Find the necessary inspection from the Result column that matches the result in the Result column from the Check Sub Bus 11 inspection.




c.

While observing the resistance value shown on the ohmmeter, disconnect branch line connectors (L182, L183 and L185) from the CAN No. 4 junction connector until the resistance becomes normal (6 kΩ or higher (for +B short) or 200 Ω or higher (for ground short)).

C316884E05
3.563,2.844 3.948,3.063 0.385,0.219 10 false L183 2.344,0.438 2.594,0.667 0.25,0.229 10 false *a 3.573,2.573 4,2.802 0.427,0.229 10 false L182 3.563,3.417 3.99,3.646 0.427,0.229 10 false L185 3.563,3.125 3.99,3.354 0.427,0.229 10 false L184 3.563,2.302 3.99,2.531 0.427,0.229 10 false L181

Text in Illustration
*a CAN No. 4 Junction Connector - -

Wiring Color
CAN No. 4 Junction Connector Side Code Color (CANH Side) Color (CANL Side)
CAN main bus line (bus line connecting CAN No. 4 junction connector and CAN No. 1 junction terminal) L181 B Y
Driving support ECU assembly*1 L182 B R
Parking assist ECU*2 L183 B L
CAN main bus line (bus line connecting power management control ECU and CAN No. 1 junction terminal) L184 B G
Lane departure warning camera*3 L185 B W

*1: w/ Pre-crash Safety System

*2: w/ Intelligent Parking Assist System

*3: w/ Lane Departure Alert System


Result:
Result Proceed to
The resistance between terminals CANH and +B, or the resistance between terminals CANL and +B is still below 6 kΩ when all the specified connectors are disconnected from the CAN junction connector.
(There is no short to +B in the branch lines.)
A
The resistance between terminals CANH and GND, or the resistance between terminals CANL and GND is still below 200 Ω when all the specified connectors are disconnected from the CAN junction connector.
(There is no short to GND in the branch lines.)
The resistance between terminals CANH and +B, or the resistance between terminals CANL and +B becomes normal (6 kΩ or higher) when a connector is disconnected from the CAN junction connector.
(There is a short to +B in one of the areas related to one or more of the disconnected branch lines.)
B
The resistance between terminals CANH and GND, or the resistance between terminals CANL and GND becomes normal (200 Ω or higher) when a connector is disconnected from the CAN junction connector.
(There is a short to GND in one of the areas related to one or more of the disconnected branch lines.)




A

15.CHECK FOR SHORT IN SUB BUS 11 LINE (CAN NO. 4 JUNCTION CONNECTOR)

B

17.CHECK FOR SHORT IN SUB BUS 11 LINE (ECU, SENSOR)
15.CHECK FOR SHORT IN SUB BUS 11 LINE (CAN NO. 4 JUNCTION CONNECTOR)
a.

Disconnect the L181 CAN No. 4 junction connector.


b.
U154245E04
1.823,2.573 1.458,2.635 false 1.865,2.573 1.573,3.031 false 2.25,2.365 2.583,2.198 false 1.823,2.365 1.656,2.146 false 2.063,3.052 2.271,3.229 0.208,0.177 10 false L5 1.031,2.583 1.396,2.76 0.365,0.177 10 false CA2L 1.115,3.021 1.5,3.198 0.385,0.177 10 false CA2H 0.146,0.052 0.844,0.385 0.698,0.333 10 false *a 2.625,2.083 3.125,2.333 0.5,0.25 10 false AM22 1.448,2.042 1.635,2.219 0.188,0.177 10 false E1

Measure the resistance according to the value(s) in the table below.

Text in Illustration
*a Rear view of wire harness connector
(to Power Management Control ECU)

Standard Resistance:
Tester Connection Condition Specified Condition Result
L5-34 (CA2H) - L5-6 (E1) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANH ground short
L5-35 (CA2L) - L5-6 (E1) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
L5-34 (CA2H) - L5-1 (AM22) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short
L5-35 (CA2L) - L5-1 (AM22) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short


HINT:

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 11 inspection.

Find the necessary inspection from the Result column that matches the result in the Result column from the Check Sub Bus 11 inspection.




OK

16.CHECK FOR SHORT IN SUB BUS 11 LINE (CAN NO. 1 JUNCTION TERMINAL)

NG

REPLACE CAN NO. 4 JUNCTION CONNECTOR

16.CHECK FOR SHORT IN SUB BUS 11 LINE (CAN NO. 1 JUNCTION TERMINAL)
a.

Reconnect the L181 CAN No. 4 junction connector.


b.

Disconnect the L180 CAN No. 1 junction terminal.


c.
U154245E04
1.823,2.573 1.458,2.635 false 1.865,2.573 1.573,3.031 false 2.25,2.365 2.583,2.198 false 1.823,2.365 1.656,2.146 false 2.063,3.052 2.271,3.229 0.208,0.177 10 false L5 1.031,2.583 1.396,2.76 0.365,0.177 10 false CA2L 1.115,3.021 1.5,3.198 0.385,0.177 10 false CA2H 0.146,0.052 0.844,0.385 0.698,0.333 10 false *a 2.625,2.083 3.125,2.333 0.5,0.25 10 false AM22 1.448,2.042 1.635,2.219 0.188,0.177 10 false E1

Measure the resistance according to the value(s) in the table below.

Text in Illustration
*a Rear view of wire harness connector
(to Power Management Control ECU)

Standard Resistance:
Tester Connection Condition Specified Condition Result
L5-34 (CA2H) - L5-6 (E1) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANH ground short
L5-35 (CA2L) - L5-6 (E1) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
L5-34 (CA2H) - L5-1 (AM22) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short
L5-35 (CA2L) - L5-1 (AM22) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short


HINT:

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 11 inspection.

Find the necessary inspection from the Result column that matches the result in the Result column from the Check Sub Bus 11 inspection.




OK

REPLACE CAN NO. 1 JUNCTION TERMINAL

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 4 JUNCTION CONNECTOR - CAN NO. 1 JUNCTION TERMINAL)

17.CHECK FOR SHORT IN SUB BUS 11 LINE (ECU, SENSOR)
a.

Reconnect the connector for the bus line that is shorted to +B or GND to the CAN junction connector (the connector that caused the bus line resistance to change to 6 kΩ or higher (for +B short) or 200 Ω or higher (for ground short) when it was disconnected).


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU to which the bus line shorted to +B or GND is connected (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>TERMINALS OF ECU).


c.
U154245E04
1.823,2.573 1.458,2.635 false 1.865,2.573 1.573,3.031 false 2.25,2.365 2.583,2.198 false 1.823,2.365 1.656,2.146 false 2.063,3.052 2.271,3.229 0.208,0.177 10 false L5 1.031,2.583 1.396,2.76 0.365,0.177 10 false CA2L 1.115,3.021 1.5,3.198 0.385,0.177 10 false CA2H 0.146,0.052 0.844,0.385 0.698,0.333 10 false *a 2.625,2.083 3.125,2.333 0.5,0.25 10 false AM22 1.448,2.042 1.635,2.219 0.188,0.177 10 false E1

Measure the resistance according to the value(s) in the table below.

Text in Illustration
*a Rear view of wire harness connector
(to Power Management Control ECU)

Standard Resistance:
Tester Connection Condition Specified Condition Result
L5-34 (CA2H) - L5-6 (E1) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANH ground short
L5-35 (CA2L) - L5-6 (E1) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
L5-34 (CA2H) - L5-1 (AM22) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short
L5-35 (CA2L) - L5-1 (AM22) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short


HINT:

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 11 inspection.

Find the necessary inspection from the Result column that matches the result in the Result column from the Check Sub Bus 11 inspection.




OK

REPLACE CORRESPONDING ECU OR SENSOR

NG

REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR BRANCH LINE OR CONNECTOR