Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU) › 2012.03–2014.11
RM2070E _57 Power Source / Network _061936 NETWORKING _0301754 CAN COMMUNICATION SYSTEM(w/o Central Gateway ECU) C

NETWORKING  CAN COMMUNICATION SYSTEM(w/o Central Gateway ECU)  U0164  Lost Communication with A/C ECU  


DESCRIPTION

DTC No. DTC Detection Condition Trouble Area
U0164 No communication from the air conditioning amplifier assembly continues.
·

Air conditioning amplifier assembly branch line or connector

·

Power source circuit of air conditioning amplifier assembly

·

Air conditioning amplifier assembly ground circuit

·

Air conditioning amplifier assembly



HINT:

This diagnosis procedure is for when DTC U0164 is output by the power management control ECU (GTS display: PM2 Gateway).


WIRING DIAGRAM

C240393E09
1.24,0.594 1.24,0.302 1.24,0.302 1.583,0.302 false 4,0.583 4,0.198 4,0.198 4.292,0.198 false 4.521,2.083 4.521,2.729 4.521,2.729 4.844,2.729 false 0.677,1.479 1.073,1.625 0.396,0.146 10 false 120 Ω 6.219,2.104 6.615,2.25 0.396,0.146 10 false ECM 6.146,1.531 6.542,1.677 0.396,0.146 10 false 120 Ω 1.656,0.229 3.792,0.438 2.135,0.208 10 false Power Management Control ECU 2.177,2.771 2.635,2.917 0.458,0.146 10 false CANH 1.635,4.323 3.906,4.625 2.271,0.302 10 false Air Conditioning Amplifier Assembly 4.208,4.365 5.115,4.552 0.906,0.188 10 false Trouble Area 2.271,2.552 2.521,2.698 0.25,0.146 10 false 11 2.896,2.552 3.156,2.698 0.26,0.146 10 false 12 2.042,3.938 2.396,4.083 0.354,0.146 10 false GND 2.042,3.365 2.396,3.51 0.354,0.146 10 false IG+ 2.042,2.885 2.396,3.031 0.354,0.146 10 false B 2.729,2.76 3.188,2.906 0.458,0.146 10 false CANL 1.115,5.021 3.146,5.198 2.031,0.177 10 false : CAN Main Bus Line (CANH) 1.115,5.417 3.146,5.594 2.031,0.177 10 false : CAN Main Bus Line (CANL) 4.26,5.021 5.979,5.198 1.719,0.177 10 false : CAN Branch Line (CANH) 4.26,5.417 5.948,5.594 1.688,0.177 10 false : CAN Branch Line (CANL) 4.354,0.115 6.521,0.448 2.167,0.333 10 false CAN No. 5 Junction Connector 4.927,2.635 6.979,2.99 2.052,0.354 10 false CAN No. 1 Junction Connector 0.99,3.531 1.375,3.708 0.385,0.177 10 false A/C 0.854,3.073 1.406,3.25 0.552,0.177 10 false ECU-B3 1.313,4.313 1.667,4.49 0.354,0.177 10 false L17 1.792,3.833 2,4.01 0.208,0.177 10 false 14 1.854,3.25 2.063,3.427 0.208,0.177 10 false 1 1.813,2.771 2.021,2.948 0.208,0.177 10 false 21 0.094,0.042 1.052,0.24 0.958,0.198 12 false Sub Bus 12: 1.656,0.063 1.969,0.26 0.313,0.198 10 false L6 5.854,2.115 6.208,2.292 0.354,0.177 10 false A57

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the power switch on (IG) and wait at least 20 seconds.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>DIAGNOSIS SYSTEM).



HINT:
·

Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.RECONFIRM DTC OUTPUT
a.

Reconfirm DTCs.

HINT:

If DTC U1002 is output from PM2 Gateway of the power management control ECU, this indicates a sub bus 12 malfunction. Troubleshoot for DTC U1002 and check for malfunctions in sub bus 12.


Result:
Result Proceed to
U1002 is not output from power management control ECU (GTS display: PM2 Gateway) A
U1002 is output from power management control ECU (GTS display: PM2 Gateway) B




A

2.CHECK FOR OPEN IN CAN BUS LINES (AIR CONDITIONING AMPLIFIER ASSEMBLY BRANCH LINE)

B

GO TO DIAGNOSIS PROCEDURE INDICATED BY OUTPUT DTC

2.CHECK FOR OPEN IN CAN BUS LINES (AIR CONDITIONING AMPLIFIER ASSEMBLY BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
U154713E02
0.193,0.154 0.341,0.495 0.148,0.341 10 *a 1.795,2.451 1.38,2.983 false 1.13,3.004 1.586,3.172 0.457,0.167 10 CANH 2.118,3.004 2.575,3.172 0.457,0.167 10 CANL 1.91,2.457 2.338,2.983 false 1.687,0.707 2.065,0.875 0.378,0.167 10 L17

Disconnect the air conditioning amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L17-11 (CANH) - L17-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Air Conditioning Amplifier Assembly)



OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY)

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
U154714E02
0.193,0.193 0.526,0.534 0.334,0.341 10 *a 2.684,1.686 3.042,1.853 0.359,0.167 10 GND 2.169,2.401 2.684,1.872 false 1.679,0.712 2.027,0.879 0.348,0.167 10 L17

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L17-14 (GND) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Air Conditioning Amplifier Assembly)


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.
U154715E01
0.193,0.157 0.480,0.498 0.287,0.341 10 *a 1.671,0.678 2.024,0.846 0.353,0.167 10 L17 0.087,1.663 0.332,1.844 0.245,0.181 10 IG+ 0.62,2.357 0.333,1.859 false 0.174,2.683 0.365,2.848 0.191,0.165 10 B 0.634,2.622 0.314,2.768 false

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L17-1 (IG+) - Body ground Power switch on (IG) 11 to 14 V
L17-21 (B) - Body ground Power switch off 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Air Conditioning Amplifier Assembly)



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)