Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU) › 2016.05–2017.12
RM2070E _57 Power Source / Network _061936 NETWORKING _0301755 CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU)  Skid Control ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Skid Control ECU Communication Stop Mode Either condition is met:
·

Communication stop for "Skid Control (ABS/VSC/TRAC)" is indicated on the "Communication Bus Check" screen of the GTS (See page (Click here)).

·

Communication system DTCs (DTCs that start with U) that correspond to "Skid Control ECU Communication Stop Mode" in "DTC Combination Table" are output (See page (Click here)).


·

Brake booster with master cylinder assembly (skid control ECU) branch line or connector

·

Power source circuit of brake booster with master cylinder assembly (skid control ECU)

·

Brake booster with master cylinder assembly (skid control ECU) ground circuit

·

Brake booster with master cylinder assembly (skid control ECU)



WIRING DIAGRAM

C356581E02
0.385,1.542 3.031,1.719 2.646,0.177 10 false No. 1 CAN Junction Connector 5.219,0.688 5.427,0.896 0.208,0.208 10 false 37 5.49,0.813 5.906,0.979 0.417,0.167 10 false CA1H 4.802,4.979 7.021,5.344 2.219,0.365 10 false Brake Booster with Master Cylinder Assembly (Skid Control ECU) 4.333,2.865 4.646,3.031 0.313,0.167 10 false IGN 4.031,2.5 5.146,2.667 1.115,0.167 10 false ECU-IG NO. 2 4.042,2.156 5.156,2.323 1.115,0.167 10 false ABS MAIN NO. 1 4.073,1.802 5.292,1.969 1.219,0.167 10 false ABS MAIN NO. 2 5.219,4.271 5.396,4.427 0.177,0.156 10 false 23 5.219,4.01 5.396,4.167 0.177,0.156 10 false 24 5.219,3.76 5.396,3.917 0.177,0.156 10 false 25 5.219,3.5 5.396,3.656 0.177,0.156 10 false 26 5.219,3.24 5.396,3.396 0.177,0.156 10 false 27 5.49,2.719 5.76,2.948 0.271,0.229 10 false IG2 5.219,2.604 5.396,2.76 0.177,0.156 10 false 12 5.49,2.365 5.76,2.594 0.271,0.229 10 false IG1 5.219,2.25 5.396,2.406 0.177,0.156 10 false 16 5.49,2 5.76,2.229 0.271,0.229 10 false BS 5.219,1.885 5.396,2.042 0.177,0.156 10 false 15 5.49,1.635 5.76,1.865 0.271,0.229 10 false BI 4.5,4.979 4.781,5.146 0.281,0.167 10 false A58 5.5,1.25 5.917,1.417 0.417,0.167 10 false CA1L 5.479,4.365 5.969,4.531 0.49,0.167 10 false GND6 5.479,4.115 5.969,4.281 0.49,0.167 10 false GND5 5.479,3.865 5.969,4.031 0.49,0.167 10 false GND4 5.469,3.594 5.958,3.76 0.49,0.167 10 false GND3 5.469,3.344 5.958,3.51 0.49,0.167 10 false GND2 5.479,3.115 5.969,3.281 0.49,0.167 10 false GND 5.208,1.146 5.417,1.354 0.208,0.208 10 false 38 5.208,2.99 5.417,3.198 0.208,0.208 10 false 28 5.219,1.531 5.396,1.688 0.177,0.156 10 false 14 0.094,1.531 0.469,1.708 0.375,0.177 10 false A67 1.604,0.99 1.979,1.167 0.375,0.177 10 false 8*1 1.615,0.542 1.99,0.719 0.375,0.177 10 false 2*1 1.604,1.167 1.979,1.344 0.375,0.177 10 false 7*2 1.615,0.708 1.99,0.885 0.375,0.177 10 false 1*2 2.49,1.646 3.833,1.823 1.344,0.177 10 false Auxiliary Battery 2.417,2.354 3.76,2.531 1.344,0.177 10 false IG1 NO. 1 Relay 2.781,2.708 4.125,2.885 1.344,0.177 10 false IG2 Relay 0.854,3.281 1.729,3.458 0.875,0.177 10 false *2: for RHD 0.854,3.01 1.729,3.188 0.875,0.177 10 false *1: for LHD

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the power switch on (IG) and wait at least 60 seconds.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSIS SYSTEM).

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK DTC (BRAKE CONTROL SYSTEM)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / ABS/VSC/TRC / Trouble Codes.

OK:

DTC C1241 is not output.




OK

2.CHECK FOR OPEN IN CAN BUS LINES (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SKID CONTROL ECU) BRANCH LINE)

NG

GO TO DIAGNOSIS PROCEDURE INDICATED BY OUTPUT DTC

2.CHECK FOR OPEN IN CAN BUS LINES (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SKID CONTROL ECU) BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
U154756E02
1.979,2.135 1.604,2.677 false 2.063,2.135 2.448,2.677 false 0.198,0.156 0.385,0.313 0.188,0.156 10 false *a 1.625,0.875 1.917,1.031 0.292,0.156 10 false A58 1.271,2.698 1.656,2.875 0.385,0.177 10 false CA1H 2.333,2.688 2.698,2.865 0.365,0.177 10 false CA1L

Disconnect the A58 brake booster with master cylinder assembly (skid control ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A58-37 (CA1H) - A58-38 (CA1L) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Brake Booster with Master Cylinder Assembly (Skid Control ECU))


Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SKID CONTROL ECU)

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SKID CONTROL ECU)

C

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SKID CONTROL ECU))