CHECK FOR INSTALLED SYSTEMS (ECUS AND SENSORS) THAT USE CAN COMMUNICATION
The systems (ECUs and sensors) that use CAN communication vary depending on the vehicle and optional equipment. Check which systems (ECUs and sensors) are installed to the vehicle.
| Bus | Code | ECU/Sensor Name | GTS Display | Applicability |
|---|---|---|---|---|
| - | CGW | Central gateway ECU (network gateway ECU) | ·
CAN Gateway1 ·
CAN Gateway2 |
Installed on all vehicles |
| V bus | DLC3 | DLC3 | - | Installed on all vehicles |
| Bus 2 | ENG | ECM | ECM (Engine) | Installed on all vehicles |
| BRK | Brake booster with master cylinder assembly (skid control ECU) | Skid Control (ABS/VSC/TRAC) | Installed on all vehicles | |
| MB | Main body ECU (multiplex network body ECU) | Main Body | Installed on all vehicles | |
| A/C | Air conditioning amplifier assembly | Air Conditioning Amplifier | Installed on all vehicles | |
| EPS | Power steering ECU assembly | Power Steering (EPS) | Installed on all vehicles | |
| SMT | Certification ECU (smart key ECU assembly) | Certification (Smart) | Installed on all vehicles | |
| STR | Spiral cable with sensor subassembly (steering angle sensor) | Spiral cable (Steering Angle Sensor) | Installed on all vehicles | |
| SRS | Airbag sensor assembly | Airbag | Installed on all vehicles | |
| PCN | Transmission control ECU assembly | Transmission Control | Installed on all vehicles | |
| MET | Combination meter subassembly | Combination Meter | Installed on all vehicles | |
| HV | Hybrid vehicle control ECU | Hybrid Vehicle Control | Installed on all vehicles | |
| Bus 3 | AV | Navigation receiver assembly | Display and Navigation (AVN) | Vehicles with Navigation Receiver Type |
| AV | Radio and display receiver assembly | Display and Navigation (AVN) | Vehicles with Radio and Display Type | |
| Bus 5 | HV | Hybrid vehicle control ECU | Hybrid Vehicle Control | Installed on all vehicles |
| PAC | Parking assist ECU | Parking Assist (Intelligent Parking Assist) | Vehicles with Intelligent Parking Assist System | |
| DS | Driving support ECU assembly | Driving Support (Cruise Control-ACC) | Vehicles with Pre-crash Safety System | |
| F-CAM | Lane departure warning camera | Front Camera Module | Vehicles with Lane Departure Alert System | |
| Sub bus 13 | DS | Driving support ECU assembly | Driving Support (Cruise Control-ACC) | Vehicles with Pre-crash Safety System |
| F-MR | Millimeter wave radar sensor assembly | - | Vehicles with Pre-crash Safety System | |
| Sub bus 15 | HV | Hybrid vehicle control ECU | Hybrid Vehicle Control | Installed on all vehicles |
| ENG | ECM | - | Installed on all vehicles | |
| BRK | Brake booster with master cylinder assembly (skid control ECU) | Skid Control (ABS/VSC/TRAC) | Installed on all vehicles |
The names of ECUs and sensors shown on the GTS display may differ from those shown in the DTC Table by ECU section.
CAN BUS CHECK
The ECUs and sensors that are properly connected to the CAN communication system can be displayed using the GTS.
Using the GTS, select the CAN Bus Check screen.
It may be possible to select buses that do not have ECUs or sensors from the bus selection pull-down menu. This is not a malfunction. (This occurs when optional devices are not on a sub bus that is monitored by a gateway function equipped ECU.)
In the bus selection pull down menu, all buses applicable to the model are displayed (e.g. LIN communication buses are also displayed). Therefore, refer to the wiring diagrams to check the names of sub buses for CAN communication (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>SYSTEM DIAGRAM).
Different connection statuses are indicated by the background color of ECUs and sensors that are displayed.
| Bus Type | Background Color | Connection Status |
|---|---|---|
| Bus 2 | White | Communication has been normal since the start of the CAN bus check. |
| Yellow | Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication). | |
| Red | Communication was established at least once since the start of the CAN bus check, but communication is currently not occurring (unstable communication). | |
| Not displayed | Communication stop has continued since the start of the CAN bus check.*1 | |
| Non-bus 2
(gateway function equipped ECU that does not have history of connected ECUs)*2 |
White | Communication has been normal since the start of the CAN bus check. |
| Yellow | Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication). | |
| Red | Communication was established at least once since the start of the CAN bus check, but communication is currently not occurring (unstable communication). | |
| Not displayed | Communication stop has continued since the start of the CAN bus check.*1 | |
| Non-bus 2
(gateway function equipped ECU that has history of connected ECUs)*3 |
White | Communication has been normal since the start of the CAN bus check. |
| Yellow | Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication). | |
| Red | Currently not communicating (either of the following):
·
Communication stop has continued since the start of the CAN bus check. ·
Communication was established at least once since the start of the CAN bus check, but communication is currently not occurring. |
|
| Not displayed | Either of the following:
·
If a gateway function equipped ECU cannot communicate, the non-bus 2 and ECUs connected to the non-bus 2 will not be displayed. ·
If no ECUs are connected to the non-bus 2, "There is no system found on the Communication Bus" will be displayed. |
Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
*1: ECUs that are present in the vehicle but are not displayed on the CAN Bus Check screen.
*2: Gateway function equipped ECU that does not memorize the non-bus 2 ECUs that are connected to it.
*3: Gateway function equipped ECU that memorizes the non-bus 2 ECUs that are connected to it.
If none of the connected ECUs are displayed, or there is no response from the vehicle to the GTS, check the central gateway ECU and the V bus main bus lines for a malfunction.
Observe the connection response screen for approximately 2 minutes to check for a change in connection status of the connected ECUs and sensors.
If an open occurs in one of the lines of a CAN branch (except DLC3), output from the other branch line (the line that is not open) will be unstable and it may interfere with the response (display) of other ECUs and sensors.
If the connection status changes during the inspection, repair the open in the branch line of the ECU or sensor that does not respond (is not detected) and then perform the CAN bus check again.
HOW TO INTERPRET CAN BUS CHECK SCREEN
When a communication stop is currently occurring, the probable malfunctioning part can be determined from the CAN bus check and by using the following methods.
The following CAN bus wiring diagram is provided only as an example. This wiring diagram is different from the actual wiring diagram for this vehicle.
When a communication stop is currently occurring, it is easier to determine the probable malfunctioning part from the CAN bus check rather than from communication DTCs.
Wait for approximately 2 minutes after turning the power switch on (IG) (or simulate the driving conditions that enable the malfunction to be reproduced) and select "CAN Bus Check". Then observe the communication status of each ECU on the screen.
If a communication error of only 1 ECU or sensor is indicated on the CAN Bus Check screen, a communication stop of the ECU or sensor is suspected.
Example: Open in both CAN branch lines of ECU D on the bus 2
| *a | Bus 2 | *b | Non-bus 2 |
| *c | V Bus | *d | Terminating Resistor |
| *e | Location of Malfunction | *f | Not displayed or background color changes to red or yellow |
| *g | CAN Bus Check Screen | *h | Central Gateway ECU (Network Gateway ECU) |
When there are communication stops, ECUs that are present in the vehicle may not be displayed on the CAN Bus Check screen.
If communication errors for multiple ECUs or sensors are indicated on the CAN Bus Check screen, then a communication stop of the ECU or sensor that shows a more serious communication stop (an ECU or sensor which is not displayed) is suspected.
Example: Open in a CAN branch line for ECU B on the bus 2
| *a | Background color periodically changes to yellow or red |
| *b | Not displayed or background color is yellow or red |
| *c | Not displayed |
| Bus Type | Background Color | Connection Status |
|---|---|---|
| Bus 2 | White | Communication has been normal since the start of the CAN bus check. |
| Yellow | Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication). | |
| Red | Communication was established at least once since the start of the CAN bus check, but communication is currently not occurring (unstable communication). | |
| Not displayed | Communication stop has continued since the start of the CAN bus check.*1 | |
| Non-bus 2
(gateway function equipped ECU that does not have history of connected ECUs)*2 |
White | Communication has been normal since the start of the CAN bus check. |
| Yellow | Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication). | |
| Red | Communication was established at least once since the start of the CAN bus check, but communication is currently not occurring (unstable communication). | |
| Not displayed | Communication stop has continued since the start of the CAN bus check.*1 | |
| Non-bus 2
(gateway function equipped ECU that has history of connected ECUs)*3 |
White | Communication has been normal since the start of the CAN bus check. |
| Yellow | Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication). | |
| Red | Currently not communicating (either of the following):
·
Communication stop has continued since the start of the CAN bus check. ·
Communication was established at least once since the start of the CAN bus check, but communication is currently not occurring. |
|
| Not displayed | Either of the following:
·
If a gateway function equipped ECU cannot communicate, the non-bus 2 and ECUs connected to the non-bus 2 will not be displayed. ·
If no ECUs are connected to the non-bus 2, "There is no system found on the Communication Bus" will be displayed. |
Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
*1: ECUs that are present in the vehicle but are not displayed on the CAN Bus Check screen.
*2: Gateway function equipped ECU that does not memorize the non-bus 2 ECUs that are connected to it.
*3: Gateway function equipped ECU that memorizes the non-bus 2 ECUs that are connected to it.
The example of the CAN Bus Check screen in the illustration shows the result of electrical noise on the CAN bus which is caused by an open in a CAN branch line of ECU B (output from the other branch line is unstable) and the communication of ECU A is also unstable. In addition, in this example, ECU A is equipped with a gateway function. Therefore, communication is also unstable between the non-bus 2 ECUs of ECU A and the bus 2.
The example in the illustration shows that ECU B is not displayed on the CAN Bus Check screen. This indicates a more significant communication stop. In this case, a communication stop of ECU B is suspected.
If a communication error is indicated on both the bus 2 and non-bus 2 on the CAN Bus Check screen, suspect any communication stop displayed for the bus 2 first.
Example: Open in both CAN branch lines of ECU A on the bus 2
| *a | Not displayed or background color changes to red |
In the CAN bus check, it is possible to confirm the communication status of ECUs connected to the bus 2 after connecting the GTS to the DLC3. As for non-bus 2, it is possible to confirm which non-bus 2 connected ECUs can communicate with a gateway function equipped ECU on the bus 2.
If a gateway function equipped ECU has a communication error, ECUs connected to the gateway function equipped ECU are also affected, and communication stops will be indicated.
The CAN Bus Check screen in the illustration shows that ECU A has a gateway function and a communication stop in ECU A is suspected.
If the CAN Bus Check screen indicates a communication stop only in the non-bus 2, a communication stop in the non-bus 2 is suspected.
Example: Open in both CAN branch lines of ECU G on the non-bus 2
| *a | Background color changes to red |
A communication error in a non-bus 2 does not affect the bus 2 or other buses.
When a gateway function equipped ECU has memorized the ECUs that are connected to the non-bus 2, if any of the ECUs connected to the gateway function equipped ECU has a communication error, the background color changes to yellow or red. (The displayed name will not disappear.)
If both of the bus 2 main bus lines are open, ECUs or sensors that are located farther away from the network gateway ECU than the open part will be displayed as a communication stop on the CAN Bus Check screen.
(In this case, ECU D and E are not displayed or their background color changes to red.)
| *a | Bus 2 | *b | Non-bus 2 |
| *c | V Bus | *d | Terminating Resistor |
| *e | Location of Malfunction | *f | Not displayed or background color changes to red or yellow |
| *g | CAN Bus Check Screen | *h | Central Gateway ECU (Network Gateway ECU) |
If a communication error occurs in an ECU, it is not displayed on the CAN Bus Check screen even though the ECU is present.
If both of the non-bus 2 main bus lines are open, ECUs that are located farther away from the network gateway ECU than the open part will be displayed as a communication stop on the CAN Bus Check screen.
(In this case, ECU I and J are not displayed or their background color changes to red.)
| *a | Bus 2 | *b | Non-bus 2 |
| *c | V Bus | *d | Terminating Resistor |
| *e | Location of Malfunction | *f | Not displayed or background color changes to red or yellow |
| *g | CAN Bus Check Screen | *h | Central Gateway ECU (Network Gateway ECU) |
When any of the following malfunctions occur, CAN communication cannot be established and almost all ECUs and sensors on the bus show a communication error on the CAN Bus Check screen.
| *a | When any of the following malfunctions occur on the bus 2 |
| *b | When any of the following malfunctions occur on a non-bus 2 |
| *c | Not displayed |
| Short between CAN lines (CANH and CANL) |
| Short between a CAN line (CANH or CANL) and +B |
| Short between a CAN line (CANH or CANL) and ground |
| Open in a CAN main bus line |
When a malfunction occurs on the bus 2, almost all ECUs and sensors in the bus 2 and non-bus 2 indicate a communication error (almost all ECUs are not displayed). As communication with the gateway function equipped ECU that is connected to the bus 2 stops, communication from the ECUs connected to the non-bus 2 that is monitored by the gateway function equipped ECU also stops (these ECUs are not displayed).
When a malfunction occurs in a non-bus 2, almost all ECUs connected to the non-bus 2 indicate a communication error.
A communication error in a non-bus 2 does not affect the bus 2 or other buses.
The malfunctioning part can be determined by checking for a short circuit between CAN bus lines or between a CAN bus line and ground or +B short using an electrical tester.
DTC TABLE BY ECU
In the CAN communication system, the CAN communication DTCs of each ECU can be displayed using the GTS.
If CAN communication system DTCs are output, the malfunction cannot be determined only by the DTCs. Perform troubleshooting according to How to Proceed with Troubleshooting (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).
If system function temporarily returns to normal, DTCs may not be output again even though the following DTC check procedures are used.
Hybrid Vehicle Control ECU / GTS Display "Hybrid Control"
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0100 | Lost Communication with ECM/PCM "A" | The hybrid vehicle control ECU does not receive data from the ECM for 0.68 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for 1 second or more. ·
The power source voltage of the hybrid vehicle control ECU is 9.5 V or more. |
Turn the power switch on (IG) and wait at least 1.68 seconds. | HV system warning light turns on. | DTC is stored until it is cleared using the GTS. |
| U0110*1 | Lost Communication with Drive Motor Control Module ''A'' | Either condition is met:
1.
The hybrid vehicle control ECU does not receive data from the MG ECU for 0.11 seconds or more. 2.
The hybrid vehicle control ECU does not send data to the MG ECU for 0.04 seconds or more. |
Both conditions are met:
·
The power switch is on (IG) for 0.1 seconds or more. ·
The power source voltage of the hybrid vehicle control ECU is 9.5 V or more. |
Turn the power switch on (IG) and wait at least 0.21 seconds. | HV system warning light turns on. | DTC is stored until it is cleared using the GTS. |
| U0129 | Lost Communication with Brake System Control Module | The hybrid vehicle control ECU does not receive data from the brake booster with master cylinder assembly (skid control ECU) for 2.34 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for 2 seconds or more. ·
The power source voltage of the hybrid vehicle control ECU is 9.5 V or more. |
Turn the power switch on (IG) and wait at least 4.34 seconds. | HV system warning light turns on. | DTC is stored until it is cleared using the GTS. |
| U0140 | Communication Error from Body ECU to HV ECU | The hybrid vehicle control ECU does not receive data from the main body ECU (multiplex network body ECU) for 3.6 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for 1 second or more. ·
The power source voltage of the hybrid vehicle control ECU is 9.5 V or more. |
Turn the power switch on (IG) and wait at least 4.6 seconds. | HV system warning light turns on. | DTC is stored until it is cleared using the GTS. |
| U0151 | Communication Error from Airbag ECU to HV ECU | The hybrid vehicle control ECU does not receive data from the airbag ECU assembly for 10.6 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for 1 second or more. ·
The power source voltage of the hybrid vehicle control ECU is 9.5 V or more. |
Turn the power switch on (IG) and wait at least 11.6 seconds. | HV system warning light turns on. | DTC is stored until it is cleared using the GTS. |
| U0164 | Communication Error from A/C ECU to HV ECU | The hybrid vehicle control ECU does not receive data from the air conditioning amplifier assembly for 10.6 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for 1 second or more. ·
The power source voltage of the hybrid vehicle control ECU is 9.5 V or more. |
Turn the power switch on (IG) and wait at least 11.6 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U029A*2 | Lost Communication with Hybrid Battery Pack Sensor Module | The hybrid vehicle control ECU does not receive data from the battery smart unit for 0.52 seconds or more. | The power switch is on (IG) for 0.5 seconds or more. | Turn the power switch on (IG) and wait at least 1.02 seconds. | HV system warning light turns on. | DTC is stored until it is cleared using the GTS. |
| U0424*1 | Invalid Data Received from HVAC Control Module | The hybrid vehicle control ECU receives an abnormal operation value command from the air conditioning amplifier assembly for 3 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for 1 second or more. ·
The power source voltage of the hybrid vehicle control ECU is 9.5 V or more. |
Turn the power switch on (IG) and wait at least 4 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U1104*3 | Lost Communication with Driving Support ECU | The hybrid vehicle control ECU does not receive data from the driving support ECU assembly for 1.02 seconds or more. | All conditions are met:
·
The power switch is on (IG) for 2.1 seconds or more. ·
The power source voltage of the hybrid vehicle control ECU is 9.5 V or more. ·
Vehicle speed is 36 km/h (22 mph) or more. |
Drive the vehicle at a speed of 36 km/h (22 mph) or more for at least 3.12 seconds. | HV system warning light turns on. | DTC is stored until it is cleared using the GTS. |
| U1107 | Lost Communication with Power Management Module | The hybrid vehicle control ECU does not receive data from the certification ECU (smart key ECU assembly) for 3.6 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for 1 second or more. ·
The power source voltage of the hybrid vehicle control ECU is 9.5 V or more. |
Turn the power switch on (IG) and wait at least 4.6 seconds. | HV system warning light turns on. | DTC is stored until it is cleared using the GTS. |
This ECU uses the CAN communication system for DTC communication.
The hybrid vehicle control ECU stores DTCs for the dynamic radar cruise control system.
*1: Refer to Hybrid Control System (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>DIAGNOSTIC TROUBLE CODE CHART).
*2: Refer to Hybrid Battery System (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>DIAGNOSTIC TROUBLE CODE CHART).
*3: Dynamic radar cruise control system DTC.
Hybrid Vehicle Control ECU / GTS Display "Cruise Control"
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0122 | Lost Communication with Vehicle Dynamic Control Module | While the cruise control system is on (the system has been switched on using the ON/OFF button on the cruise control switch), the hybrid vehicle control ECU does not receive data from the brake booster with master cylinder assembly (skid control ECU) for 2.73 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for 2.1 seconds or more. ·
The power source voltage of the hybrid vehicle control ECU is 9.5 V or more. |
After turning the power switch on (IG), turn the cruise control main switch on and wait for at least 4.83 seconds. | ·
Cruise control indicator light (amber) illuminates. ·
Displays messages on the multi-information display. |
DTC is stored until it is cleared using the GTS. |
This ECU uses the CAN communication system for DTC communication.
The hybrid vehicle control ECU stores DTCs for the cruise control system.
ECM / GTS Display "Engine and ECT"
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0293 | Lost Communication with HV ECU | The ECM does not receive data from the hybrid vehicle control ECU for 0.576 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for 1 second or more. ·
The power source voltage of the ECM is 10.5 V or more. |
Turn the power switch on (IG) and wait at least 1.576 seconds. | - | DTC is stored until it is cleared using the GTS. |
This ECU uses the CAN communication system for DTC communication.
Transmission Control ECU Assembly / GTS Display "Transmission Control"
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0146 | Lost Communication with Body ECU | The transmission control ECU assembly does not receive data from the main body ECU (multiplex network body ECU) for 10 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for 1 second or more. ·
The power source voltage of the transmission control ECU assembly is 10 V or more. |
Turn the power switch on (IG) and wait at least 11 seconds. | - | DTC is stored until it is cleared using the GTS. |
This ECU uses the CAN communication system for DTC communication.
Power Steering ECU Assembly / GTS Display "EMPS"
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0129 | Lost Communication with Brake System Control Module | The power steering ECU assembly does not receive data from the brake booster with master cylinder assembly (skid control ECU) for 2.3 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for 2 seconds or more. ·
The power source voltage of the power steering ECU assembly is 9 V or more. |
Turn the power switch on (IG) and wait at least 4.3 seconds. | EPS warning light illuminates. | DTC remains stored only while malfunction is occurring. |
| U0293 | Lost Communication with Hybrid Control Module | The power steering ECU assembly does not receive data from the hybrid vehicle control ECU for 2.3 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for 2 seconds or more. ·
The power source voltage of the power steering ECU assembly is 9 V or more. |
Turn the power switch on (IG) and wait at least 4.3 seconds. | EPS warning light illuminates. | DTC remains stored only while malfunction is occurring. |
| U1105 | Lost Communication with Parking Assist ECU | The power steering ECU assembly does not receive data from the parking assist ECU for 1.34 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for 2 seconds or more. ·
The power source voltage of the power steering ECU assembly is 9 V or more. |
Turn the power switch on (IG) and wait at least 3.34 seconds. | EPS warning light illuminates. | DTC remains stored only while malfunction is occurring. |
This ECU uses the CAN communication system for DTC communication.
Brake booster with master cylinder (Skid control ECU) / GTS Display "ABS/VSC/TRC"
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0073 | Control Module Communication Bus OFF | One of the following conditions is met:
1.
The brake booster with master cylinder assembly (skid control ECU) keeps sending data to an ECU or sensor for 5 seconds or more because a reception completion cannot be received. 2.
The airbag ECU assembly or spiral cable with sensor sub-assembly (steering angle sensor) and brake booster with master cylinder assembly (skid control ECU) cannot communicate for 1 second or more. 3.
The following condition occurs 10 times in succession within 60 seconds: - The airbag ECU assembly or spiral cable with sensor sub-assembly (steering angle sensor) cannot communicate with the brake booster with master cylinder assembly (skid control ECU) once or more within 5 seconds. 4.
The following condition occurs 10 times in succession: - The brake booster with master cylinder assembly (skid control ECU) cannot send/receive data (bus off) once or more within 0.1 seconds. |
Both conditions are met:
·
The power switch is on (IG) for 1 second or more. ·
The power source voltage of the brake booster with master cylinder assembly (skid control ECU) is between 10 and 17.4 V. |
Turn the power switch on (IG) and wait at least 60 seconds. | ·
ABS warning light illuminates. ·
Brake warning light illuminates (yellow). ·
Slip warning light illuminates. |
DTC is stored until it is cleared using the GTS. |
| U0120 | Lost Communication with Starter / Generator Control Module | The brake booster with master cylinder assembly (skid control ECU) does not receive data from the certification ECU (smart key ECU assembly) for 3 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for 1 second or more. ·
The power source voltage of the brake booster with master cylinder assembly (skid control ECU) is between 10 and 17.4 V. |
Turn the power switch on (IG) and wait at least 4 seconds. | Brake warning light illuminates (yellow). | DTC is stored until it is cleared using the GTS. |
| U0123 | Lost Communication with Yaw Rate Sensor Module | Either condition is met:
1.
The brake booster with master cylinder assembly (skid control ECU) does not receive data from the airbag ECU assembly for 1 second or more. 2.
The following condition occurs 10 times in succession within 60 seconds: - The brake booster with master cylinder assembly (skid control ECU) does not receive data from the airbag ECU assembly once or more within 5 seconds. |
Both conditions are met:
·
The power switch is on (IG) for 1 second or more. ·
The power source voltage of the brake booster with master cylinder assembly (skid control ECU) is between 10 and 17.4 V. |
Turn the power switch on (IG) and wait at least 60 seconds. | ·
ABS warning light illuminates. ·
Brake warning light illuminates (yellow). ·
Slip warning light illuminates. |
DTC is stored until it is cleared using the GTS. |
| U0124 | Lost Communication with Lateral Acceleration Sensor Module | Either condition is met:
1.
The brake booster with master cylinder assembly (skid control ECU) does not receive data from the airbag ECU assembly for 1 second or more. 2.
The following condition occurs 10 times in succession within 60 seconds: - The brake booster with master cylinder assembly (skid control ECU) does not receive data from the airbag ECU assembly once or more within 5 seconds. |
Both conditions are met:
·
The power switch is on (IG) for 1 second or more. ·
The power source voltage of the brake booster with master cylinder assembly (skid control ECU) is between 10 and 17.4 V. |
Turn the power switch on (IG) and wait at least 60 seconds. | ·
ABS warning light illuminates. ·
Brake warning light illuminates (yellow). ·
Slip warning light illuminates. |
DTC is stored until it is cleared using the GTS. |
| U0126 | Lost Communication with Steering Angle Sensor Module | Either condition is met:
1.
The brake booster with master cylinder assembly (skid control ECU) does not receive data from the spiral cable with sensor sub-assembly (steering angle sensor) for 1 second or more. 2.
The following condition occurs 10 times in succession within 60 seconds: - The brake booster with master cylinder assembly (skid control ECU) does not receive data from the spiral cable with sensor sub-assembly (steering angle sensor) once or more within 5 seconds. |
Both conditions are met:
·
The power switch is on (IG) for 1 second or more. ·
The power source voltage of the brake booster with master cylinder assembly (skid control ECU) is between 10 and 17.4 V. |
Turn the power switch on (IG) and wait at least 60 seconds. | Slip warning light illuminates. | DTC is stored until it is cleared using the GTS. |
| U0293 | Communication Error from HV ECU | Either condition is met:
1.
The brake booster with master cylinder assembly (skid control ECU) does not receive data from the hybrid vehicle control ECU for 2 seconds or more. 2.
The following condition occurs 10 times in succession within 60 seconds: - With the IG2 terminal voltage of the brake booster with master cylinder assembly (skid control ECU) at 9.5 V or more, the brake booster with master cylinder assembly (skid control ECU) does not receive data from the hybrid vehicle control ECU once or more within 5 seconds. |
Both conditions are met:
·
The power switch is on (IG) for 1 second or more. ·
The power source voltage of the brake booster with master cylinder assembly (skid control ECU) is between 10 and 17.4 V. |
Turn the power switch on (IG) and wait at least 60 seconds. | ·
Brake warning light illuminates (yellow). ·
Slip warning light illuminates. |
DTC is stored until it is cleared using the GTS. |
This ECU uses the CAN communication system for DTC communication.
Spiral Cable with Sensor Sub-assembly (Steering Angle Sensor) / GTS Display "-"
The spiral cable with sensor sub-assembly (steering angle sensor) is connected to the CAN communication system, but the spiral cable with sensor sub-assembly (steering angle sensor) does not store or output CAN communication DTCs.
Airbag Sensor Assembly / GTS Display "SRS Airbag"
The airbag sensor assembly is connected to the CAN communication system, but the airbag sensor assembly does not store or output CAN communication DTCs.
Main Body ECU (Multiplex Network Body ECU) / GTS Display "Main Body"
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0100 | Lost Communication with ECM/ PCM "A" | The main body ECU (multiplex network body ECU) does not receive data from the ECM for 10 seconds or more. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and 10 seconds or more have elapsed. ·
The power source voltage of the main body ECU (multiplex network body ECU) is 9.5 V or more. |
Turn the power switch on (IG) and wait at least 20 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0101 | Lost Communication with TCM | The main body ECU (multiplex network body ECU) does not receive data from the transmission control ECU assembly for 10 seconds or more. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and 10 seconds or more have elapsed. ·
The power source voltage of the main body ECU (multiplex network body ECU) is 9.5 V or more. |
Turn the power switch on (IG) and wait at least 20 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0120 | Lost Communication with Starter / Generator Control Module | The main body ECU (multiplex network body ECU) does not receive data from the certification ECU (smart key ECU assembly) for 10 seconds or more. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and 10 seconds or more have elapsed. ·
The power source voltage of the main body ECU (multiplex network body ECU) is 9.5 V or more. |
Turn the power switch on (IG) and wait at least 20 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0129 | Lost Communication with Brake System Control Module | The main body ECU (multiplex network body ECU) does not receive data from the brake booster with master cylinder assembly (skid control ECU) for 10 seconds or more. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and 10 seconds or more have elapsed. ·
The power source voltage of the main body ECU (multiplex network body ECU) is 9.5 V or more. |
Turn the power switch on (IG) and wait at least 20 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0151 | Lost Communication with Restraints Control Module | The main body ECU (multiplex network body ECU) does not receive data from the airbag ECU assembly for 10 seconds or more. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and 10 seconds or more have elapsed. ·
The power source voltage of the main body ECU (multiplex network body ECU) is 9.5 V or more. |
Turn the power switch on (IG) and wait at least 20 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0155 | Lost Communication with Instrument Panel Cluster | The main body ECU (multiplex network body ECU) does not receive data from the combination meter sub-assembly for 10 seconds or more. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and 10 seconds or more have elapsed. ·
The power source voltage of the main body ECU (multiplex network body ECU) is 9.5 V or more. |
Turn the power switch on (IG) and wait at least 20 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0164 | Lost Communication with HVAC Control Module | The main body ECU (multiplex network body ECU) does not receive data from the air conditioning amplifier assembly for 10 seconds or more. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and 10 seconds or more have elapsed. ·
The power source voltage of the main body ECU (multiplex network body ECU) is 9.5 V or more. |
Turn the power switch on (IG) and wait at least 20 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U023A | Lost Communication with Image Processing Module "A" | The main body ECU (multiplex network body ECU) does not receive data from the lane departure warning camera for 5 seconds or more. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and 10 seconds or more have elapsed. ·
The power source voltage of the main body ECU (multiplex network body ECU) is 9.5 V or more. |
Turn the power switch on (IG) and wait at least 15 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0293 | Lost Communication with Hybrid Powertrain Control Module | The main body ECU (multiplex network body ECU) does not receive data from the hybrid vehicle control ECU for 10 seconds or more. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and 10 seconds or more have elapsed. ·
The power source voltage of the main body ECU (multiplex network body ECU) is 9.5 V or more. |
Turn the power switch on (IG) and wait at least 20 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0327 | Software Incompatibility with Vehicle Security | The main body ECU (multiplex network body ECU) does not receive data from the certification ECU (smart key ECU assembly) for 10 seconds or more. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and 10 seconds or more have elapsed. ·
The power source voltage of the main body ECU (multiplex network body ECU) is 9.5 V or more. |
Turn the power switch on (IG) and wait at least 20 seconds. | - | DTC is stored until it is cleared using the GTS. |
This ECU uses the CAN communication system for DTC communication.
Certification ECU (Smart Key ECU Assembly) / GTS Display "Power Source Control"
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0103 | Lost Communication with Gear Shift Module "A" | The certification ECU (smart key ECU assembly) does not receive data from the transmission control ECU assembly for 5 seconds or more. | Both conditions are met:
·
The power switch is on (IG). ·
The power source voltage of the certification ECU (smart key ECU assembly) is 10 V or more. |
Turn the power switch on (IG) and wait at least 5 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0129 | Vehicle Speed Signal Communication | The certification ECU (smart key ECU assembly) does not receive vehicle speed data from the brake booster with master cylinder assembly (skid control ECU) for 3 seconds or more. | Both conditions are met:
·
The power switch is on (IG). ·
The power source voltage of the certification ECU (smart key ECU assembly) is 10 V or more. |
Turn the power switch on (IG) and wait at least 3 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0140 | Lost Communication with Main Body ECU | The certification ECU (smart key ECU assembly) does not receive data from the main body ECU (multiplex network body ECU) for 3 seconds or more. | Both conditions are met:
·
The power switch is on (IG). ·
The power source voltage of the certification ECU (smart key ECU assembly) is 10 V or more. |
Turn the power switch on (IG) and wait at least 3 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0293 | HV ECU Communication | The certification ECU (smart key ECU assembly) does not receive data from the hybrid vehicle control ECU for 3.1 seconds or more. | Both conditions are met:
·
The power switch is on (IG). ·
The power source voltage of the certification ECU (smart key ECU assembly) is 10 V or more. |
Turn the power switch on (IG) and wait at least 3.1 seconds. | - | DTC is stored until it is cleared using the GTS. |
This ECU uses the CAN communication system for DTC communication.
Certification ECU (Smart Key ECU Assembly) / GTS Display "Entry&Start"
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0100 | Lost Communication with ECM / PCM "A" | The certification ECU (smart key ECU assembly) does not receive data from the ECM for 10 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for 1 second or more. ·
The power source voltage of the certification ECU (smart key ECU assembly) is 10 V or more. |
Turn the power switch on (IG) and wait at least 11 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0142 | Lost Communication with Body Control Module "B" | The certification ECU (smart key ECU assembly) does not receive data from the main body ECU (multiplex network body ECU) for 10 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for 1 second or more. ·
The power source voltage of the certification ECU (smart key ECU assembly) is 10 V or more. |
Turn the power switch on (IG) and wait at least 11 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0155 | Lost Communication with Instrument Panel Cluster (IPC) Control Module | The certification ECU (smart key ECU assembly) does not receive data from the combination meter sub-assembly for 10 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for 1 second or more. ·
The power source voltage of the certification ECU (smart key ECU assembly) is 10 V or more. |
Turn the power switch on (IG) and wait at least 11 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0293 | Lost Communication with HV ECU | The certification ECU (smart key ECU assembly) does not receive data from the hybrid vehicle control ECU for 10 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for 1 second or more. ·
The power source voltage of the certification ECU (smart key ECU assembly) is 10 V or more. |
Turn the power switch on (IG) and wait at least 11 seconds. | - | DTC is stored until it is cleared using the GTS. |
This ECU uses the CAN communication system for DTC communication.
Air Conditioning Amplifier Assembly / GTS Display "Air Conditioner"
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0100 | Lost Communication with ECM / PCM ''A'' | The air conditioning amplifier assembly does not receive data from the ECM for 5 seconds or more. | Both conditions are met:
·
The power switch is on (IG). ·
The power source voltage of the air conditioning amplifier assembly is 8.5 V or more. |
Turn the power switch on (IG) and wait at least 5 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0131 | Lost Communication with Power Steering Control Module | The air conditioning amplifier assembly does not receive data from the power steering ECU assembly for 5 seconds or more. | Both conditions are met:
·
The power switch is on (IG). ·
The power source voltage of the air conditioning amplifier assembly is 8.5 V or more. |
Turn the power switch on (IG) and wait at least 5 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0142 | Lost Communication with Body Control Module ''B'' | The air conditioning amplifier assembly does not receive data from the main body ECU (multiplex network body ECU) for 5 seconds or more. | Both conditions are met:
·
The power switch is on (IG). ·
The power source voltage of the air conditioning amplifier assembly is 8.5 V or more. |
Turn the power switch on (IG) and wait at least 5 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0155 | Lost Communication with Instrument Panel Cluster Control Module (Combination Meter) | The air conditioning amplifier assembly does not receive data from the combination meter sub-assembly for 5 seconds or more. | Both conditions are met:
·
The power switch is on (IG). ·
The power source voltage of the air conditioning amplifier assembly is 8.5 V or more. |
Turn the power switch on (IG) and wait at least 5 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0293 | Lost Communication with HV ECU | The air conditioning amplifier assembly does not receive data from the hybrid vehicle control ECU for 5 seconds or more. | Both conditions are met:
·
The power switch is on (IG). ·
The power source voltage of the air conditioning amplifier assembly is 8.5 V or more. |
Turn the power switch on (IG) and wait at least 5 seconds. | - | DTC is stored until it is cleared using the GTS. |
This ECU uses the CAN communication system for DTC communication.
Combination Meter Sub-assembly / GTS Display "Combination Meter"
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0100 | Lost Communication with ECM / PCM "A" | The combination meter sub-assembly does not receive data from the hybrid vehicle control ECU for 2 seconds or more. | Both conditions are met:
·
The power switch is on (IG). ·
The power source voltage of the combination meter sub-assembly is 9.5 V or more. |
Turn the power switch on (IG) and wait at least 2 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0129 | Lost Communication with Skid Control ECU | The combination meter sub-assembly does not receive data from the brake booster with master cylinder assembly (skid control ECU) for 3 seconds or more. | Both conditions are met:
·
The power switch is on (IG). ·
The power source voltage of the combination meter sub-assembly is 9.5 V or more. |
Turn the power switch on (IG) and wait at least 3 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0131 | Lost Communication with Power Steering Control Module | The combination meter sub-assembly does not receive data from the power steering ECU assembly for 3 seconds or more. | Both conditions are met:
·
The power switch is on (IG). ·
The power source voltage of the combination meter sub-assembly is 9.5 V or more. |
Turn the power switch on (IG) and wait at least 3 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0142 | Lost Communication with Body Control Module "B" | The combination meter sub-assembly does not receive data from the main body ECU (multiplex network body ECU) for 10 seconds or more. | Both conditions are met:
·
The power switch is on (IG). ·
The power source voltage of the combination meter sub-assembly is 9.5 V or more. |
Turn the power switch on (IG) and wait at least 10 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0151 | Lost Communication with Airbag ECU | The combination meter sub-assembly does not receive data from the airbag ECU assembly for 10 seconds or more. | Both conditions are met:
·
The power switch is on (IG). ·
The power source voltage of the combination meter sub-assembly is 9.5 V or more. |
Turn the power switch on (IG) and wait at least 10 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0163 | Lost Communication with Navigation Control Module | The combination meter sub-assembly does not receive data from the navigation receiver assembly for 10 seconds or more. | Both conditions are met:
·
The power switch is on (IG). ·
The power source voltage of the combination meter sub-assembly is 9.5 V or more. |
Turn the power switch on (IG) and wait at least 10 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U023A | Lost Communication with Front Camera Module | The combination meter sub-assembly does not receive data from the lane departure warning camera for 10 seconds or more. | Both conditions are met:
·
The power switch is on (IG). ·
The power source voltage of the combination meter sub-assembly is 9.5 V or more. |
Turn the power switch on (IG) and wait at least 10 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U1104 | Lost Communication with Driving Support ECU | The combination meter sub-assembly does not receive data from the driving support ECU assembly for 10 seconds or more. | Both conditions are met:
·
The power switch is on (IG). ·
The power source voltage of the combination meter sub-assembly is 9.5 V or more. |
Turn the power switch on (IG) and wait at least 10 seconds. | - | DTC is stored until it is cleared using the GTS. |
This ECU uses the CAN communication system for DTC communication.
Navigation Receiver Assembly / GTS Display "Navigation System"
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0073 | Sending Malfunction (Navigation to APGS) | The navigation receiver assembly does not send/receive data for 5 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for 1 second or more. ·
The power source voltage of the navigation receiver assembly is 9.5 V or more. |
Turn the power switch on (IG) and wait at least 6 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0100 | Lost Communication with ECM / PCM "A" | The navigation receiver assembly does not receive data from the ECM for 4 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for 1 second or more. ·
The power source voltage of the navigation receiver assembly is 9.5 V or more. |
Turn the power switch on (IG) and wait at least 5 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0129 | Lost Communication with Brake System Control Module | The navigation receiver assembly does not receive data from the brake booster with master cylinder assembly (skid control ECU) for 1 second or more. | Both conditions are met:
·
The power switch is on (IG) for 1 second or more. ·
The power source voltage of the navigation receiver assembly is 9.5 V or more. |
Turn the power switch on (IG) and wait at least 2 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0140 | Lost Communication with Body Control Module | The navigation receiver assembly does not receive data from the main body ECU (multiplex network body ECU) for 3 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for 1 second or more. ·
The power source voltage of the navigation receiver assembly is 9.5 V or more. |
Turn the power switch on (IG) and wait at least 4 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0155 | Meter ECU Communication | The navigation receiver assembly does not receive data from the combination meter sub-assembly for 30 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for 1 second or more. ·
The power source voltage of the navigation receiver assembly is 9.5 V or more. |
Turn the power switch on (IG) and wait at least 31 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0293 | Lost Communication with HV ECU | The navigation receiver assembly does not receive data from the hybrid vehicle control ECU for 4 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for 1 second or more. ·
The power source voltage of the navigation receiver assembly is 9.5 V or more. |
Turn the power switch on (IG) and wait at least 5 seconds. | - | DTC is stored until it is cleared using the GTS. |
This ECU uses the CAN communication system for DTC communication.
Radio and Display Receiver Assembly / GTS Display "Navigation System"
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0073 | Sending Malfunction (Navigation to APGS) | The radio and display receiver assembly does not send/receive data for 5 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for 1 second or more. ·
The power source voltage of the radio and display receiver assembly is 9.5 V or more. |
Turn the power switch on (IG) and wait at least 6 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0100 | Lost Communication with ECM / PCM "A" | The radio and display receiver assembly does not receive data from the ECM for 4 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for 1 second or more. ·
The power source voltage of the radio and display receiver assembly is 9.5 V or more. |
Turn the power switch on (IG) and wait at least 5 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0129 | Lost Communication with Brake System Control Module | The radio and display receiver assembly does not receive data from the brake booster with master cylinder assembly (skid control ECU) for 1 second or more. | Both conditions are met:
·
The power switch is on (IG) for 1 second or more. ·
The power source voltage of the radio and display receiver assembly is 9.5 V or more. |
Turn the power switch on (IG) and wait at least 2 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0140 | Lost Communication with Body Control Module | The radio and display receiver assembly does not receive data from the main body ECU (multiplex network body ECU) for 3 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for 1 second or more. ·
The power source voltage of the radio and display receiver assembly is 9.5 V or more. |
Turn the power switch on (IG) and wait at least 4 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0155 | Meter ECU Communication | The radio and display receiver assembly does not receive data from the combination meter sub-assembly for 30 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for 1 second or more. ·
The power source voltage of the radio and display receiver assembly is 9.5 V or more. |
Turn the power switch on (IG) and wait at least 31 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0293 | Lost Communication with HV ECU | The radio and display receiver assembly does not receive data from the hybrid vehicle control ECU for 4 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for 1 second or more. ·
The power source voltage of the radio and display receiver assembly is 9.5 V or more. |
Turn the power switch on (IG) and wait at least 5 seconds. | - | DTC is stored until it is cleared using the GTS. |
This ECU uses the CAN communication system for DTC communication.
Driving Support ECU Assembly / GTS Display "Pre-Crash2"
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0122 | Lost Communication with Vehicle Dynamics Control Module | The driving support ECU assembly does not receive data from the brake booster with master cylinder assembly (skid control ECU) for 5.24 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for 2 seconds or more. ·
The power source voltage of the driving support ECU assembly is 10 V or more. |
Turn the power switch on (IG) and wait at least 7.24 seconds. | ·
PCS warning light blinks. ·
Displays messages on the multi-information display. |
DTC is stored until it is cleared using the GTS. |
| U0123 | Lost Communication with Yaw Rate Sensor Module | The driving support ECU assembly does not receive data from the airbag sensor assembly for 0.772 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for 3 seconds or more. ·
The power source voltage of the driving support ECU assembly is 10 V or more. |
Turn the power switch on (IG) and wait at least 3.772 seconds. | ·
PCS warning light blinks. ·
Displays messages on the multi-information display. |
DTC is stored until it is cleared using the GTS. |
| U0126 | Lost Communication with Steering Angle Sensor Module | The driving support ECU assembly does not receive data from the spiral cable with sensor sub-assembly (steering angle sensor) for 3.76 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for 1 second or more. ·
The power source voltage of the driving support ECU assembly is 10 V or more. |
Turn the power switch on (IG) and wait at least 4.76 seconds. | ·
PCS warning light blinks. ·
Displays messages on the multi-information display. |
DTC is stored until it is cleared using the GTS. |
| U0142 | Lost Communication with Body Control Module "B" | The driving support ECU assembly does not receive data from the main body ECU (multiplex network body ECU) for 14.2 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for 1 second or more. ·
The power source voltage of the driving support ECU assembly is 10 V or more. |
Turn the power switch on (IG) and wait at least 15.2 seconds. | ·
PCS warning light blinks. ·
Displays messages on the multi-information display. |
DTC is stored until it is cleared using the GTS. |
| U0235*1 | Lost Communication with Cruise Control Front Distance Range Sensor | The driving support ECU assembly does not receive data from the millimeter wave radar sensor assembly for 0.652 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for 1 second or more. ·
The power source voltage of the driving support ECU assembly is 10 V or more. |
Turn the power switch on (IG) and wait at least 1.652 seconds. | ·
PCS warning light blinks. ·
Displays messages on the multi-information display. |
DTC is stored until it is cleared using the GTS. |
| U0293 | Lost Communication with HV ECU | Either of the following conditions is met:
·
The driving support ECU assembly does not receive data from the hybrid vehicle control ECU for 3.808 seconds or more. ·
The brake booster with master cylinder assembly (skid control ECU) does not receive data from the hybrid vehicle control ECU for 0.8 seconds or more. |
All conditions are met:
·
The power switch is on (IG) for 1 second or more. ·
The power source voltage of the driving support ECU assembly is 10 V or more. ·
Vehicle speed is 5 km/h (3 mph) or more. |
Drive the vehicle at a speed of 5 km/h (3 mph) or more for at least 4.808 seconds. | ·
PCS warning light blinks. ·
Displays messages on the multi-information display. |
DTC is stored until it is cleared using the GTS. |
| U1002 | Lost Communication with Gateway Module | The driving support ECU assembly does not receive data from the millimeter wave radar sensor assembly for 0.652 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for 1 second or more. ·
The power source voltage of the driving support ECU assembly is 10 V or more. |
Turn the power switch on (IG) and wait at least 1.652 seconds. | ·
PCS warning light blinks. ·
Displays messages on the multi-information display. |
DTC is stored until it is cleared using the GTS. |
| U1104*2 | Lost Communication with Driving Support ECU | The ECM, brake booster with master cylinder assembly (skid control ECU) or millimeter wave radar sensor assembly does not receive data from the driving support ECU assembly for 1.504 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for 2 seconds or more. ·
The power source voltage of the driving support ECU assembly is 10 V or more. |
Turn the power switch on (IG) and wait at least 3.504 seconds. | ·
PCS warning light blinks. ·
Displays messages on the multi-information display. |
DTC is stored until it is cleared using the GTS. |
This ECU uses the CAN communication system for DTC communication.
*1: If only U0235 is output, CAN communication is normal. Refer to Pre-Crash Safety System (See page Vehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>U0235).
*2: If only U1104 is output, CAN communication is normal. Refer to Pre-Crash Safety System (See page Vehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>U0122).
Driving Support ECU Assembly / GTS Display "Radar Cruise"
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0122 | Lost Communication with Vehicle Dynamics Control Module | The driving support ECU assembly does not receive data from the brake booster with master cylinder assembly (skid control ECU) for 5.24 seconds or more. | All conditions are met:
·
The power switch is on (IG) for 2 seconds or more. ·
The cruise control main switch is on. ·
The power source voltage of the driving support ECU assembly is 10 V or more. ·
Vehicle speed is 36 km/h (22 mph) or more. |
Turn the cruise control main switch on and drive the vehicle at a speed of 36 km/h (22 mph) or more for 7.24 seconds or more. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0123 | Lost Communication with Yaw Rate Sensor Module | The driving support ECU assembly does not receive data from the airbag sensor assembly for 0.772 seconds or more. | All conditions are met:
·
The power switch is on (IG) for 3 seconds or more. ·
The cruise control main switch is on. ·
The power source voltage of the driving support ECU assembly is 10 V or more. ·
Vehicle speed is 36 km/h (22 mph) or more. |
Turn the cruise control main switch on and drive the vehicle at a speed of 36 km/h (22 mph) or more for 3.772 seconds or more. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0126 | Lost Communication with Steering Angle Sensor Module | The driving support ECU assembly does not receive data from the spiral cable with sensor sub-assembly (steering angle sensor) for 3.76 seconds or more. | All conditions are met:
·
The power switch is on (IG) for 1 second or more. ·
The cruise control main switch is on. ·
The power source voltage of the driving support ECU assembly is 10 V or more. ·
Vehicle speed is 36 km/h (22 mph) or more. |
Turn the cruise control main switch on and drive the vehicle at a speed of 36 km/h (22 mph) or more for 4.76 seconds or more. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0235*1 | Lost Communication with Cruise Control Front Distance Range Sensor | The driving support ECU assembly does not receive data from the millimeter wave radar sensor assembly for 0.652 seconds or more. | All conditions are met:
·
The power switch is on (IG) for 1 second or more. ·
The cruise control main switch is on. ·
The power source voltage of the driving support ECU assembly is 10 V or more. ·
Vehicle speed is 36 km/h (22 mph) or more. |
Turn the cruise control main switch on and drive the vehicle at a speed of 36 km/h (22 mph) or more for 1.652 seconds or more. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0293 | Lost Communication with HV ECU | Either of the following conditions is met:
·
The driving support ECU assembly does not receive data from the hybrid vehicle control ECU for 3.808 seconds or more. ·
The brake booster with master cylinder assembly (skid control ECU) does not receive data from the hybrid vehicle control ECU for 0.8 seconds or more. |
All conditions are met:
·
The power switch is on (IG) for 1 second or more. ·
The cruise control main switch is on. ·
The power source voltage of the driving support ECU assembly is 10 V or more. ·
Vehicle speed is 36 km/h (22 mph) or more. |
Turn the cruise control main switch on and drive the vehicle at a speed of 36 km/h (22 mph) or more for 4.808 seconds or more. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U1104*2 | Lost Communication with Driving Support ECU | The ECM, brake booster with master cylinder assembly (skid control ECU) or millimeter wave radar sensor assembly does not receive data from the driving support ECU assembly for 1 second or more. | All conditions are met:
·
The power switch is on (IG) for 2 seconds or more. ·
The cruise control main switch is on. ·
The power source voltage of the driving support ECU assembly is 10 V or more. ·
Vehicle speed is 36 km/h (22 mph) or more. |
Turn the cruise control main switch on and drive the vehicle at a speed of 36 km/h (22 mph) or more for 1.8 seconds or more. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
This ECU uses the CAN communication system for DTC communication.
*1: If only U0235 is output, CAN communication is normal. Refer to Dynamic Radar Cruise Control System (See page Engine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>U0235).
*2: If only U1104 is output, CAN communication is normal. Refer to Dynamic Radar Cruise Control System (See page Engine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>U0122).
Parking Assist ECU / GTS Display "IPA/Parking Assist Monitor"
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0073 | Control Module Communication Bus Off | Either condition is met:
1.
The parking assist ECU keeps sending data to an ECU or a sensor for 1.24 seconds or more because a reception completion signal cannot be received. 2.
The parking assist ECU detects that it is disconnected from the bus (bus off) 10 times in succession. |
Both conditions are met:
·
The power switch is on (IG) for 1 second or more. ·
The power source voltage of the parking assist ECU is 10 V or more. |
Turn the power switch on (IG) and wait at least 10 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0100 | Lost Communication with ECM / PCM ''A'' | The parking assist ECU does not receive data from the hybrid vehicle control ECU for 10 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for 1 second or more. ·
The power source voltage of the parking assist ECU is 10 V or more. |
Turn the power switch on (IG) and wait at least 11 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0126 | Lost Communication with Steering Angle Sensor Module | The parking assist ECU does not receive data from the spiral cable with sensor sub-assembly (steering angle sensor) for 10 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for 1 second or more. ·
The power source voltage of the parking assist ECU is 10 V or more. |
Turn the power switch on (IG) and wait at least 11 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0129 | Lost Communication with Brake System Control Module | The parking assist ECU does not receive data from the brake booster with master cylinder assembly (skid control ECU) for 1.24 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for 1 second or more. ·
The power source voltage of the parking assist ECU is 10 V or more. |
Turn the power switch on (IG) and wait at least 2.24 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0131 | Lost Communication with Power Steering Control Module | The parking assist ECU does not receive data from the power steering ECU assembly for 1.4 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for 1 second or more. ·
The power source voltage of the parking assist ECU is 10 V or more. |
Turn the power switch on (IG) and wait at least 2.4 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0140 | Lost Communication with Main Body ECU | The parking assist ECU does not receive data from the main body ECU (multiplex network body ECU) for 10 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for 1 second or more. ·
The power source voltage of the parking assist ECU is 10 V or more. |
Turn the power switch on (IG) and wait at least 11 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0293 | Lost Communication with HV ECU | The parking assist ECU does not receive data from the hybrid vehicle control ECU (HV ECU) for 2.34 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for 1 second or more. ·
The power source voltage of the parking assist ECU is 10 V or more. |
Turn the power switch on (IG) and wait at least 3.34 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U1000* | Can Communication Failure (Message Registry) | When the power switch is turned on (IG), a CAN communication malfunction is detected. | Both conditions are met:
·
The power switch is on (IG). ·
The power source voltage of the parking assist ECU is 10 V or more. |
Turn the power switch on (IG). | - | DTC is stored until it is cleared using the GTS. |
This ECU uses the CAN communication system for DTC communication.
*: If only U1000 is output, CAN communication is normal. Refer to Intelligent Parking Assist System (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>INTELLIGENT PARKING ASSIST SYSTEM>U1000).
Millimeter Wave Radar Sensor Assembly / GTS Display "-"
The millimeter wave radar sensor assembly is connected to the CAN communication system, but CAN communication DTCs are not output.
Lane Departure Warning Camera / GTS Display "Lane Departure Alert"
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0101 | Lost Communication with TCM | The lane departure warning camera does not receive data from the hybrid vehicle control ECU for 5 seconds or more. | All conditions are met:
·
The power switch is on (IG) for 2 seconds or more. ·
Vehicle speed is 1 km/h (1 mph) or more. ·
The power source voltage of the lane departure warning camera is 10 V or more. |
Drive the vehicle at a speed of 1 km/h (1 mph) or more for 7 seconds or more. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0123 | Lost Communication with Yaw Rate Sensor Module | The lane departure warning camera does not receive data from the airbag sensor assembly for 5 seconds or more. | All conditions are met:
·
The power switch is on (IG) for 2 seconds or more. ·
Vehicle speed is 1 km/h (1 mph) or more. ·
The power source voltage of the lane departure warning camera is 10 V or more. |
Drive the vehicle at a speed of 1 km/h (1 mph) or more for 7 seconds or more. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0129 | Lost Communication with Brake System Control Module | The lane departure warning camera does not receive data from the brake booster with master cylinder assembly (skid control ECU) for 5 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for 2 seconds or more. ·
The power source voltage of the lane departure warning camera is 10 V or more. |
Turn the power switch on (IG) and wait at least 7 seconds. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0142 | Lost Communication with Body Control Module "B" | The lane departure warning camera does not receive data from the main body ECU (multiplex network body ECU) for 5 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for 2 seconds or more. ·
The power source voltage of the lane departure warning camera is 10 V or more. |
Turn the power switch on (IG) and wait at least 7 seconds. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0155 | Lost Communication with Instrument Panel Cluster (IPC) Control Module | The lane departure warning camera does not receive data from the combination meter sub-assembly for 50 seconds or more. | Both conditions are met:
·
The power switch is on (IG) for 2 seconds or more. ·
The power source voltage of the lane departure warning camera is 10 V or more. |
Turn the power switch on (IG) and wait at least 52 seconds. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U1000* | Lost Communication Failure (Message Registry) | When the power switch is turned on (IG), a CAN communication malfunction is detected. | The power switch is on (IG). | Turn the power switch on (IG). | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
This ECU uses the CAN communication system for DTC communication.
*: The lane departure warning camera monitors its internal condition, when an internal malfunction is detected, the lane departure warning camera stores U1000 and cancels lane departure alert system control (See page Engine / Hybrid System>CRUISE CONTROL>LANE DEPARTURE ALERT SYSTEM>U1000).
Central Gateway ECU (Network Gateway ECU) / GTS Display "Central Gateway"
The central gateway ECU (network gateway ECU) is connected to the CAN communication system, but the central gateway ECU (network gateway ECU) does not store or output CAN communication DTCs.
CAN BUS WAVEFORMS
The following waveform is measured between terminals CANH and GND, and terminals CANL and GND of the central gateway ECU (network gateway ECU). (Use this as a reference for diagnosis of CAN communication lines.)
When malfunctions in multiple ECUs are suspected based on the CAN bus check and DTCs checked using the GTS, check the resistance of the CAN bus using an ohmmeter first. If no problems are found, check the following waveforms (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).
If a waveform is not similar to one of the following 3 patterns (Group 1), then an open in a CAN main bus line, an open in a CAN branch line, or a short between a CAN line (CANH or CANL) and ground is suspected (Group 2).
Wiggle the connector and wire harness to check if the waveform changes.
CAN bus waveforms (Group 1)
Normal waveform
Open in both of the lines (CANH and CANL) of a CAN branch
Waveforms (waveforms shown using dotted lines) are not present from an ECU or sensor connected to a CAN branch with an open circuit in both lines. (Waveforms from other ECUs or sensors are normal.)
Because this waveform is similar to a normal waveform, instead of using the waveform, the malfunctioning part can be narrowed down by performing a CAN bus check.
Short between the CAN bus lines (CANH and CANL)
Waveforms disappear.
If the malfunction is in an ECU, disconnecting the ECU will change the waveform. If the waveform does not change, a malfunction in the wire harness is suspected.
CAN bus waveforms (reference) (Group 2)
The following CAN bus waveforms can be used only as reference. The actual measured waveform may differ significantly depending on the location of the open or short circuit.
Open in a CAN branch line (CANH)
An abnormal waveform is output from an ECU with an open in one of its CAN branch lines. Because this abnormal output interferes with the signals from other ECUs, the output of other ECUs will also appear abnormal.
Narrow down the malfunctioning part by checking DTCs or performing a CAN bus check, or by checking waveform changes when ECUs or sensors are disconnected. The waveform will change to one for an open in both sides of a CAN branch when the ECU or sensor with an open CAN branch line is disconnected.
Open in a CAN branch line (CANL)
An abnormal waveform is output from an ECU with an open in one of its CAN branch lines. Because this abnormal output interferes with the signals from other ECUs, the output of other ECUs will also appear abnormal.
Narrow down the malfunctioning part by checking DTCs or performing a CAN bus check, or by checking waveform changes when ECUs or sensors are disconnected. The waveform will change to one for an open in both sides of a CAN branch when the ECU or sensor with an open CAN branch line is disconnected.
Open in a CAN main bus line (CANH)
Waveforms of ECUs or sensors that are closer to the central gateway ECU (network gateway ECU) than the open part are almost normal.
Waveforms of ECUs or sensors that are on the opposite side of the central gateway ECU (network gateway ECU) from the open part are abnormal.
An open in a CAN main bus line can be confirmed by measuring the resistance between the CANH and CANL terminals of any CAN branch.
Short between a CAN bus line (CANH) and ground
Narrow down the shorted part by checking for waveform changes when disconnecting connectors from the CAN junction connectors or when disconnecting ECUs or sensors.
A short to ground in the CANH line can be confirmed by measuring the resistance between CANH and ground using an ohmmeter.
Short between a CAN bus line (CANL) and ground
Narrow down the shorted part by checking for waveform changes when disconnecting connectors from the CAN junction connectors or when disconnecting ECUs or sensors.
A short to ground in the CANL line can be confirmed by measuring the resistance between CANL and ground using an ohmmeter.
DATA SENDING/RECEIVING TABLE
Data sending/receiving table
If Data List items related to sent/received data are not displayed properly, the part for which communication is interrupted can be determined using the table below.
*1: Whether the ECU that sends data is functioning or not can be judged by using the GTS to check items such as switches or sensors that send signals to the ECU via direct lines.
*2: Although the received contents cannot be checked in the Data List, whether or not the data is received normally can be checked by observing the combination meter.
*3: The combination meter sub-assembly receives a vehicle speed signal from the brake actuator assembly (skid control ECU) and sends the signal to other ECUs.