Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU) › from 2016.05
RM2070E _57 Power Source / Network _061936 NETWORKING _0301755 CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU)  Certification ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Certification ECU Communication Stop Mode Either condition is met:
·

Communication stop for "Certification (Smart)" is indicated on the "Communication Bus Check" screen of the GTS (See page (Click here)).

·

Communication system DTCs (DTCs that start with U) that correspond to "Certification ECU Communication Stop Mode" in "DTC Combination Table" are output (See page (Click here)).


·

Certification ECU (smart key ECU assembly) branch line or connector

·

Power source circuit of certification ECU (smart key ECU assembly)

·

Certification ECU (smart key ECU assembly) ground circuit

·

Certification ECU (smart key ECU assembly)



WIRING DIAGRAM

C346648E23
0.427,1.323 2.958,1.688 2.531,0.365 10 false No. 2 CAN Junction Connector 5.125,0.531 5.531,0.771 0.406,0.24 10 false L197 5.125,1.052 5.5,1.281 0.375,0.229 10 false L197 5.125,1.865 5.5,2.094 0.375,0.229 10 false L195 5.125,3.365 5.5,3.594 0.375,0.229 10 false L195 5.135,2.604 5.51,2.833 0.375,0.229 10 false L197 5.208,3.188 5.583,3.417 0.375,0.229 10 false 11 5.552,3.375 5.927,3.604 0.375,0.229 10 false E 5.229,2.417 5.604,2.646 0.375,0.229 10 false 5 5.542,2.615 5.917,2.844 0.375,0.229 10 false IG 5.219,1.688 5.594,1.917 0.375,0.229 10 false 2 5.542,1.875 5.917,2.104 0.375,0.229 10 false +B 5.188,0.865 5.563,1.094 0.375,0.229 10 false 15 5.177,0.344 5.552,0.573 0.375,0.229 10 false 14 5.531,0.531 6.01,0.76 0.479,0.229 10 false CANH 5.542,1.063 6.021,1.292 0.479,0.229 10 false CANL 4.25,4.208 7.083,4.583 2.833,0.375 10 false Certification ECU (Smart Key ECU Assembly) 4.146,2.75 4.802,3 0.656,0.25 10 false IGN 4.031,2.021 5.219,2.354 1.188,0.333 10 false ECU-B2 1.948,1.833 3.396,2.208 1.448,0.375 10 false from Auxiliary Battery 2.344,2.573 3.26,2.854 0.917,0.281 10 false from IG2 Relay 1.677,0.438 2,0.667 0.323,0.229 10 false 7*2 1.667,0.958 1.979,1.156 0.313,0.198 10 false 8*2 0.135,1.323 0.75,1.521 0.615,0.198 10 false L94 1.667,0.823 1.979,1.021 0.313,0.198 10 false 7*1 1.677,0.281 2,0.51 0.323,0.229 10 false 8*1 0.646,3.385 2.333,3.583 1.688,0.198 10 false *1: for LHD 0.646,3.75 2.333,3.948 1.688,0.198 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the power switch on (IG) and wait at least 20 seconds.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSIS SYSTEM).

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
U190835E03
1.417,1.823 1.906,1.177 false 2.573,1.823 2.083,1.177 false 1.594,0.25 2.031,0.521 0.438,0.271 10 false L197 0.083,0.052 0.375,0.208 0.292,0.156 10 false *a 1.188,1.875 1.698,2.125 0.51,0.25 10 false CANH 2.469,1.875 2.948,2.146 0.479,0.271 10 false CANL

Disconnect the L197 certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L197-14 (CANH) - L197-15 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly))



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Disconnect the L195 certification ECU (smart key ECU assembly) connector.


b.
U191281E02
2.385,1.167 2.708,0.677 false 1.135,3.667 0.813,3.177 false 2.323,3.302 2.635,2.802 false 1.552,0.365 2.271,0.708 0.719,0.344 10 false L197 0.135,0.125 0.51,0.417 0.375,0.292 10 false *a 1.573,2.625 2.188,2.865 0.615,0.24 10 false L195 2.74,0.521 3.104,0.792 0.365,0.271 10 false IG 0.698,2.99 1.042,3.26 0.344,0.271 10 false E 2.656,2.635 3.021,2.896 0.365,0.26 10 false +B

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L195-11 (E) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



c.

Reconnect the cable to the negative (-) auxiliary battery terminal.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L195-2 (+B) - Body ground Power switch off 11 to 14 V
L197-5 (IG) - Body ground Power switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly))



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)