Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU) › from 2016.05
RM2070E _57 Power Source / Network _061936 NETWORKING _0301755 CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU)  Air Conditioning Amplifier Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Air Conditioning Amplifier Communication Stop Mode Either condition is met:
·

Communication stop for "Air Conditioning Amplifier" is indicated on the "Communication Bus Check" screen of the GTS (See page (Click here)).

·

Communication system DTCs (DTCs that start with U) that correspond to "Air Conditioning Amplifier Communication Stop Mode" in "DTC Combination Table" are output (See page (Click here)).


·

Air conditioning amplifier assembly branch line or connector

·

Power source circuit of air conditioning amplifier assembly

·

Air conditioning amplifier assembly ground circuit

·

Air conditioning amplifier assembly



WIRING DIAGRAM

C348667E40
0.625,1.958 3.427,2.271 2.802,0.313 10 false No. 2 CAN Junction Connector 0.302,1.958 0.635,2.219 0.333,0.26 10 false L95 1.719,1.479 2.052,1.74 0.333,0.26 10 false 5*2 1.729,0.896 2.063,1.156 0.333,0.26 10 false 6*2 5.396,0.865 5.729,1.125 0.333,0.26 10 false 11 5.385,1.438 5.719,1.698 0.333,0.26 10 false 12 4.125,2.615 4.76,2.802 0.635,0.188 10 false ECU-B3 5.385,2.344 5.719,2.604 0.333,0.26 10 false 21 5.385,3.177 5.719,3.438 0.333,0.26 10 false 1 4.229,3.438 4.646,3.667 0.417,0.229 10 false A/C 1.708,2.448 3.396,2.771 1.688,0.323 10 false from Auxiliary Battery 1.708,3.292 3.271,3.604 1.563,0.313 10 false from IG1 NO. 1 Relay 5.396,3.99 5.729,4.25 0.333,0.26 10 false 14 5.656,4.146 5.99,4.406 0.333,0.26 10 false GND 5.667,3.313 6,3.573 0.333,0.26 10 false IG+ 5.667,2.5 6,2.76 0.333,0.26 10 false B 5.656,0.99 6.281,1.24 0.625,0.25 10 false CANH 5.667,1.573 6.344,1.885 0.677,0.313 10 false CANL 5.229,4.781 5.563,5.042 0.333,0.26 10 false L17 5.521,4.781 7.052,5.323 1.531,0.542 10 false Air Conditioning Amplifier Assembly 1.719,1.479 2.052,1.74 0.333,0.26 10 false 5*2 1.719,1.323 2.052,1.583 0.333,0.26 10 false 6*1 1.729,0.75 2.063,1.01 0.333,0.26 10 false 5*1 0.354,4.073 2.042,4.271 1.688,0.198 10 false *1: for LHD 0.354,4.406 2.042,4.604 1.688,0.198 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the power switch on (IG) and wait at least 60 seconds.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSIS SYSTEM).

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (AIR CONDITIONING AMPLIFIER ASSEMBLY BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
U191097E01
0.156,0.149 0.358,0.357 0.202,0.207 10 *a 0.927,0.571 1.388,0.768 0.461,0.196 10 CANH 2.29,0.568 2.750,0.765 0.461,0.196 10 CANL 1.464,0.655 1.815,0.655 1.815,0.655 1.815,2.13 false 2.258,0.657 1.935,0.657 1.935,0.657 1.935,2.133 false 0.515,1.203 0.797,1.384 0.281,0.181 10 L17

Disconnect the L17 air conditioning amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L17-11 (CANH) - L17-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Air Conditioning Amplifier Assembly)



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
U191098E02
0.927,1.25 0.646,1.25 0.646,1.25 0.646,2.125 false 2.469,1.25 2.146,1.25 2.146,1.25 2.146,2.135 false 0.635,2.354 0.635,2.802 0.635,2.802 0.813,2.802 false 0.156,0.083 0.354,0.292 0.198,0.208 10 false *a 2.521,1.167 2.958,1.385 0.438,0.219 10 false GND 0.99,1.167 1.323,1.438 0.333,0.271 10 false IG+ 1.125,0.688 1.427,0.917 0.302,0.229 10 false L17 0.885,2.719 1.167,3.021 0.281,0.302 10 false B

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L17-14 (GND) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to Air Conditioning Amplifier Assembly)

b.

Reconnect the cable to the negative (-) auxiliary battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L17-1 (IG+) - Body ground Power switch on (IG) 11 to 14 V
L17-21 (B) - Body ground Power switch off 11 to 14 V




OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)