Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU) › from 2016.05
RM2070E _57 Power Source / Network _061936 NETWORKING _0301755 CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU)  Transmission Control ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Transmission Control ECU Communication Stop Mode Either condition is met:
·

Communication stop for "Transmission Control" is indicated on the "Communication Bus Check" screen of the GTS (See page (Click here)).

·

Communication system DTCs (DTCs that start with U) that correspond to "Transmission Control ECU Communication Stop Mode" in "DTC Combination Table" are output (See page (Click here)).


·

Transmission control ECU assembly branch line or connector

·

Power source circuit of transmission control ECU assembly

·

Transmission control ECU assembly ground circuit

·

Transmission control ECU assembly



WIRING DIAGRAM

C354495E05
0.448,1.333 2.573,1.594 2.125,0.26 10 false No. 3 CAN Junction Connector 0.135,1.333 0.51,1.563 0.375,0.229 10 false A68 1.688,0.438 2.063,0.667 0.375,0.229 10 false 2*2 1.688,0.948 2.063,1.177 0.375,0.229 10 false 8*2 5.146,0.531 5.521,0.76 0.375,0.229 10 false A24 5.156,1.063 5.531,1.292 0.375,0.229 10 false A24 5.188,0.344 5.563,0.573 0.375,0.229 10 false 16 5.188,0.865 5.563,1.094 0.375,0.229 10 false 15 5.531,0.552 6.01,0.76 0.479,0.208 10 false CA1H 5.542,1.073 6.021,1.281 0.479,0.208 10 false CA1L 5.156,3.802 5.531,4.031 0.375,0.229 10 false A24 5.146,3.344 5.521,3.573 0.375,0.229 10 false A24 5.146,2.833 5.521,3.063 0.375,0.229 10 false A24 5.219,2.635 5.594,2.865 0.375,0.229 10 false 1 5.229,3.156 5.604,3.385 0.375,0.229 10 false 5 5.229,3.615 5.604,3.844 0.375,0.229 10 false 6 5.573,2.823 5.948,3.052 0.375,0.229 10 false E1 5.542,3.354 5.917,3.583 0.375,0.229 10 false E02 5.531,3.833 5.906,4.063 0.375,0.229 10 false E01 5.146,1.698 5.521,1.927 0.375,0.229 10 false A23 5.146,2.302 5.521,2.531 0.375,0.229 10 false A23 5.177,1.51 5.656,1.719 0.479,0.208 10 false 15 5.542,1.708 6.021,1.917 0.479,0.208 10 false BATT 5.177,2.104 5.656,2.313 0.479,0.208 10 false 16 5.552,2.292 6.031,2.5 0.479,0.208 10 false +B 4.771,4.208 7.083,4.51 2.313,0.302 10 false Transmission Control ECU Assembly 3.698,2.458 4.531,2.677 0.833,0.219 10 false IGCT NO. 2 2.063,2.302 3.177,2.563 1.115,0.26 10 false from IGCT Relay 3.729,1.844 4.698,2.125 0.969,0.281 10 false P CON MAIN 1.719,1.688 3.135,1.938 1.417,0.25 10 false from Auxiliary Battery 1.688,0.302 2.063,0.531 0.375,0.229 10 false 1*1 1.688,0.802 2.063,1.031 0.375,0.229 10 false 7*1 0.771,3.021 2.188,3.271 1.417,0.25 10 false *1: for LHD 0.771,3.333 2.188,3.583 1.417,0.25 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the power switch on (IG) and wait at least 11 seconds.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSIS SYSTEM).

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (TRANSMISSION CONTROL ECU ASSEMBLY BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
U154770E02
2.063,1.969 1.948,2.51 false 2.167,1.969 2.333,2.521 false 0.115,0.094 0.344,0.271 0.229,0.177 10 false *a 1.656,2.583 2.042,2.76 0.385,0.177 10 false CA1L 2.271,2.573 2.677,2.75 0.406,0.177 10 false CA1H 1.615,0.688 1.875,0.865 0.26,0.177 10 false A24

Disconnect the A24 transmission control ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A24-16 (CA1H) - A24-15 (CA1L) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Transmission Control ECU Assembly)



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (TRANSMISSION CONTROL ECU ASSEMBLY)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
U191012E02
2.229,3.708 2.521,4.125 true 2.26,1.313 2.542,0.771 true 2.031,1.313 1.74,0.771 true 1.208,1.313 0.906,0.948 true 0.115,0.073 0.344,0.25 0.229,0.177 10 false *a 0.521,1.438 0.781,1.615 0.26,0.177 10 false A24 0.521,3.51 0.781,3.688 0.26,0.177 10 false A23 2.552,4.156 2.927,4.333 0.375,0.177 10 false +B 2.448,0.542 2.771,0.719 0.323,0.177 10 false E01 1.531,0.552 1.906,0.729 0.375,0.177 10 false E02 0.677,0.719 0.865,0.896 0.188,0.177 10 false E1

Disconnect the A23 transmission control ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A24-1 (E1) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
A24-5 (E02) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
A24-6 (E01) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



c.

Reconnect the cable to the negative (-) auxiliary battery terminal.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A23-16 (+B) - Body ground Power switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Transmission Control ECU Assembly)



OK

REPLACE TRANSMISSION CONTROL ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)