Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU) › 2016.05–2017.12
RM2070E _57 Power Source / Network _061936 NETWORKING _0301755 CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU)  Driving Support ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Driving Support ECU Communication Stop Mode Either condition is met:
·

Communication stop for "Driving Support (Cruise Control-ACC)" is indicated on the "Communication Bus Check" screen of the GTS (See page (Click here)).

·

Communication system DTCs (DTCs that start with U) that correspond to "Driving Support ECU Communication Stop Mode" in "DTC Combination Table" are output (See page (Click here)).


·

Driving support ECU assembly branch line or connector

·

Power source circuit of driving support ECU assembly

·

Driving support ECU assembly ground circuit

·

Driving support ECU assembly



WIRING DIAGRAM

C279376E46
5.229,3.927 5.948,4.292 0.719,0.365 10 false L60 5.219,4.094 6.531,4.49 1.313,0.396 10 false Driving Support ECU Assembly 5.646,3.479 7.073,3.792 1.427,0.313 10 false GND 5.667,2.635 7.094,2.948 1.427,0.313 10 false B 5.667,1.75 7.094,2.063 1.427,0.313 10 false CA2L 5.656,1.177 7.083,1.49 1.427,0.313 10 false CA2H 5.385,1.615 6.813,1.927 1.427,0.313 10 false 17 5.385,1.031 6.813,1.344 1.427,0.313 10 false 39 5.396,2.521 6.823,2.833 1.427,0.313 10 false 30 5.385,3.344 6.813,3.656 1.427,0.313 10 false 25 3.833,2.75 5.26,3.063 1.427,0.313 10 false ECU-IG1 NO. 2 1.74,2.625 3.042,2.844 1.302,0.219 10 false from IG1 NO. 1 Relay 1.729,1.583 2.042,1.958 0.313,0.375 10 false 2 1.719,1.01 2.24,1.333 0.521,0.323 10 false 1 0.313,2.063 1.021,2.406 0.708,0.344 10 false L182 0.302,2.229 2.552,2.51 2.25,0.281 10 false No. 4 CAN Junction Connector

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the power switch on (IG) and wait at least 10 seconds, turn the cruise control main switch on and wait at least 1 second, and then drive the vehicle at a speed of 36 km/h (22 mph) or more for 6.04 seconds or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSIS SYSTEM).

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (DRIVING SUPPORT ECU ASSEMBLY BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
U191156E02
2.698,1.917 2.115,2.74 false 2.729,1.74 2.146,0.99 false 1.646,0.333 1.99,0.51 0.344,0.177 10 false L60 0.115,0.104 0.271,0.281 0.156,0.177 10 false *a 1.938,0.792 2.323,0.969 0.385,0.177 10 false CA2L 1.906,2.76 2.292,2.938 0.385,0.177 10 false CA2H

Disconnect the L60 driving support ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L60-39 (CA2H) - L60-17 (CA2L) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Driving Support ECU Assembly)



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (DRIVING SUPPORT ECU ASSEMBLY)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
U191157E02
1.76,1.906 2.25,2.74 false 1.292,1.906 0.906,2.719 false 1.573,0.365 1.917,0.542 0.344,0.177 10 false L60 0.115,0.104 0.271,0.281 0.156,0.177 10 false *a 2.24,2.75 2.417,2.927 0.177,0.177 10 false B 0.708,2.729 1.083,2.906 0.375,0.177 10 false GND

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L60-25 (GND) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) auxiliary battery terminal.

Text in Illustration
*a Front view of wire harness connector
(to Driving Support ECU Assembly)


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L60-30 (B) - Body ground Power switch switch on (IG) 11 to 14 V




OK

REPLACE DRIVING SUPPORT ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)