Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU) › from 2016.05
RM2070E _57 Power Source / Network _061936 NETWORKING _0301755 CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU)  Parking Assist ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Parking Assist ECU Communication Stop Mode Either condition is met:
·

Communication stop for "Parking Assist (Intelligent Parking Assist)" is indicated on the "Communication Bus Check" screen of the GTS (See page (Click here)).

·

Communication system DTCs (DTCs that start with U) that correspond to "Parking Assist ECU Communication Stop Mode" in "DTC Combination Table" are output (See page (Click here)).


·

Parking assist ECU branch line or connector

·

Power source circuit of parking assist ECU

·

Parking assist ECU ground circuit

·

Parking assist ECU



WIRING DIAGRAM

C354496E09
0.625,1.333 3.531,1.531 2.906,0.198 10 false No. 4 CAN Junction Connector 0.25,1.333 0.688,1.583 0.438,0.25 10 false L183 1.677,0.427 2.115,0.677 0.438,0.25 10 false 1 1.677,0.948 2.115,1.198 0.438,0.25 10 false 2 5.167,0.542 5.604,0.792 0.438,0.25 10 false L65 5.156,1.063 5.594,1.313 0.438,0.25 10 false L65 5.167,1.698 5.604,1.948 0.438,0.25 10 false L64 5.156,2.292 5.594,2.542 0.438,0.25 10 false L64 5.156,2.865 5.594,3.115 0.438,0.25 10 false L64 5.156,3.531 5.594,3.781 0.438,0.25 10 false L64 5.188,0.354 5.417,0.594 0.229,0.24 10 false 40 5.542,0.542 5.979,0.792 0.438,0.25 10 false CANH 5.563,1.063 6,1.313 0.438,0.25 10 false CANL 5.552,1.708 5.99,1.958 0.438,0.25 10 false +B 5.198,0.875 5.427,1.115 0.229,0.24 10 false 39 5.229,1.521 5.667,1.771 0.438,0.25 10 false 1 5.542,2.302 5.979,2.552 0.438,0.25 10 false IG 5.552,2.885 5.99,3.135 0.438,0.25 10 false ACC 5.542,3.542 5.979,3.792 0.438,0.25 10 false GND1 5.229,3.354 5.667,3.604 0.438,0.25 10 false 4 5.219,2.688 5.656,2.938 0.438,0.25 10 false 9 5.229,2.104 5.667,2.354 0.438,0.25 10 false 8 3.708,1.844 4.646,2.115 0.938,0.271 10 false RAD NO. 1 3.646,2.458 4.708,2.729 1.063,0.271 10 false ECU-IG NO. 2 3.729,3.021 4.583,3.323 0.854,0.302 10 false ECU-ACC 5.396,4.219 6.948,4.521 1.552,0.302 10 false Parking Assist ECU 1.76,1.708 3.167,2.042 1.406,0.333 10 false from Auxiliary Battery 1.771,2.292 3.26,2.573 1.49,0.281 10 false from IG1 NO. 1 Relay 2.063,2.854 3.51,3.167 1.448,0.313 10 false from ACC Relay

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the power switch on (IG) and wait at least 60 seconds.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSIS SYSTEM).

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (PARKING ASSIST ECU BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
U191301E01
2.901,1.856 3.331,2.002 0.431,0.147 10 CANH 1.766,1.856 2.404,2.002 0.637,0.147 10 CANL 2.728,1.47 2.87,1.969 false 2.608,1.47 2.303,1.935 false 2.153,0.214 2.417,0.395 0.264,0.181 10 L65 0.123,0.097 0.288,0.244 0.165,0.147 10 *a

Disconnect the L65 parking assist ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L65-40 (CANH) - L65-39 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Parking Assist ECU)



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (PARKING ASSIST ECU)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Disconnect the L64 parking assist ECU connector.


b.
U191000E02
0.865,2.906 1.323,2.292 false 0.521,1.167 0.917,1.917 false 1.74,2.875 1.49,2.281 false 2.24,1.021 2.625,1.927 false 0.125,0.083 0.281,0.26 0.156,0.177 10 false *a 0.698,2.865 1.094,3.042 0.396,0.177 10 false IG 0.302,1.042 0.698,1.219 0.396,0.177 10 false +B 1.781,2.844 2.188,3.021 0.406,0.177 10 false ACC 1.844,0.938 2.281,1.115 0.438,0.177 10 false GND1 0.188,1.979 0.438,2.156 0.25,0.177 10 false L64

Measure the resistance according to the value(s) in the table below.

Text in Illustration
*a Front view of wire harness connector
(to Parking Assist ECU)

Standard Resistance:
Tester Connection Condition Specified Condition
L64-4 (GND1) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



c.

Reconnect the cable to the negative (-) auxiliary battery terminal.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L64-1 (+B) - Body ground Power switch off 11 to 14 V
L64-8 (IG) - Body ground Power switch on (IG) 11 to 14 V
L64-9 (ACC) - Body ground Power switch on (ACC) 11 to 14 V




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)