Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU) › from 2016.05
RM2070E _57 Power Source / Network _061936 NETWORKING _0301755 CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU)  Open in Bus 2 Main Bus Line (LHD Models)  


DESCRIPTION

There may be an open circuit in one of the CAN main bus lines when the resistance between terminals 18 (CA4H) and 17 (CA4L) of the central gateway ECU (network gateway ECU) is 70 Ω or higher.

Symptom Trouble Area
Resistance between terminals 18 (CA4H) and 17 (CA4L) of the central gateway ECU (network gateway ECU) is 70 Ω or higher.
·

CAN main bus lines or connector

·

Central gateway ECU (network gateway ECU) branch line or connector

·

ECM

·

Combination meter sub-assembly

·

No. 1 CAN junction connector

·

No. 2 CAN junction connector

·

No. 3 CAN junction connector



This malfunction is not related to the lines of a CAN branch or to ECUs or sensors connected to a CAN branch.

WIRING DIAGRAM

C354534E04
0.823,1.365 1.198,1.594 0.375,0.229 10 false ECM 0.542,1.365 0.875,1.604 0.333,0.24 10 false A57 0.438,0.698 1.167,0.938 0.729,0.24 10 false 120 Ω 0.99,0.844 1.719,1.083 0.729,0.24 10 false CANL 0.969,0.302 1.698,0.542 0.729,0.24 10 false CANH 1.448,0.302 1.729,0.531 0.281,0.229 10 false 13 1.458,0.844 1.74,1.073 0.281,0.229 10 false 5 2.771,0.417 3.052,0.646 0.281,0.229 10 false A67 2.781,0.948 3.063,1.177 0.281,0.229 10 false A67 3.969,0.417 4.385,0.656 0.417,0.24 10 false L132 3.969,0.948 4.385,1.188 0.417,0.24 10 false L132 2.854,0.229 3.135,0.458 0.281,0.229 10 false 1 2.854,0.75 3.135,0.979 0.281,0.229 10 false 7 4.073,0.24 4.354,0.469 0.281,0.229 10 false 6 4.031,0.76 4.313,0.99 0.281,0.229 10 false 12 2.604,1.354 4.5,1.708 1.896,0.354 10 false No. 1 CAN Junction Connector 3.99,2.427 4.271,2.656 0.281,0.229 10 false L94 4,2.958 4.281,3.188 0.281,0.229 10 false L94 2.792,3.51 3.073,3.74 0.281,0.229 10 false L94 2.781,4.042 3.063,4.271 0.281,0.229 10 false L94 2.781,2.958 3.063,3.188 0.281,0.229 10 false L95 2.792,2.427 3.073,2.656 0.281,0.229 10 false L95 4.063,2.24 4.344,2.469 0.281,0.229 10 false 5 4.073,2.771 4.354,3 0.281,0.229 10 false 4 2.823,2.24 3.104,2.469 0.281,0.229 10 false 11 2.813,2.76 3.094,2.99 0.281,0.229 10 false 12 0.969,2.417 1.448,2.635 0.479,0.219 10 false CA4H 0.99,2.948 1.469,3.167 0.479,0.219 10 false CA4L 1.448,2.844 1.927,3.063 0.479,0.219 10 false 17 1.458,2.323 1.938,2.542 0.479,0.219 10 false 18 0.073,3.344 0.479,3.583 0.406,0.24 10 false L192 0.406,3.344 1.781,3.969 1.375,0.625 10 false Central Gateway ECU (Network Gateway ECU) 2.854,3.333 3.135,3.563 0.281,0.229 10 false 2 2.854,3.854 3.135,4.083 0.281,0.229 10 false 1 2.938,5.01 3.219,5.24 0.281,0.229 10 false 5 2.229,6.073 2.625,6.323 0.396,0.25 10 false L133 3.969,5.531 4.25,5.76 0.281,0.229 10 false 12 3.99,5.01 4.271,5.24 0.281,0.229 10 false 6 2.875,5.531 3.156,5.76 0.281,0.229 10 false 11 6.375,5.385 7.104,5.625 0.729,0.24 10 false 120 Ω 5.885,4.99 6.615,5.229 0.729,0.24 10 false CANH 5.885,5.521 6.615,5.76 0.729,0.24 10 false CANL 5.625,5 5.906,5.229 0.281,0.229 10 false 19 5.615,5.531 5.896,5.76 0.281,0.229 10 false 20 5.479,6.042 5.76,6.271 0.281,0.229 10 false L27 5.781,6.031 6.969,6.51 1.188,0.479 10 false Combination Meter Sub-assembly 2.531,4.375 4.427,4.729 1.896,0.354 10 false No. 2 CAN Junction Connector 2.583,6.083 4.479,6.438 1.896,0.354 10 false No. 3 CAN Junction Connector

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the power switch on (IG), turn the cruise control system on using the cruise control switch (ON/OFF switch), wait at least 60 seconds, and then drive the vehicle at a speed of 50 km/h (31 mph) or more for at least 1.72 seconds.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSIS SYSTEM).



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the L192 central gateway ECU (network gateway ECU) connector.


c.
U191184E02
1.656,1.198 1.344,1.792 false 1.792,1.198 2.094,1.792 false 0.073,0.042 0.24,0.198 0.167,0.156 10 false *a 1.542,0.167 2.104,0.417 0.563,0.25 10 false L192 1.125,1.813 1.573,2.073 0.448,0.26 10 false CA4L 1.938,1.813 2.521,2.073 0.583,0.26 10 false CA4H

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L192-18 (CA4H) - L192-17 (CA4L) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to Central Gateway ECU (Network Gateway ECU))

NOTICE:

When the measured value is 133 Ω or higher and a CAN communication system DTC is output, there may be a fault besides disconnection of the central gateway ECU (network gateway ECU) branch line. For that reason, troubleshooting should be performed again from How to Proceed with Troubleshooting after repairing the trouble area (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).




OK

2.CHECK FOR OPEN IN CAN BUS LINES (ECM)

NG

REPAIR OR REPLACE CAN BRANCH LINE CONNECTED TO CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

2.CHECK FOR OPEN IN CAN BUS LINES (ECM)
a.
U154712E01
1.603,0.657 1.906,0.813 0.303,0.156 10 A57 0.178,0.182 0.532,0.455 0.353,0.273 10 *a 2.581,1.039 3.042,1.275 0.461,0.236 10 CANH 2.473,0.795 2.950,1.045 0.477,0.250 10 CANL 1.93,1.677 2.184,0.892 2.184,0.892 2.43,0.892 false 1.958,1.789 2.242,1.117 2.242,1.117 2.533,1.117 false

Disconnect the A57 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A57-13 (CANH) - A57-5 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to ECM)



OK

NG

3.CHECK FOR OPEN IN CAN BUS LINES (COMBINATION METER SUB-ASSEMBLY)
3.CHECK FOR OPEN IN CAN BUS LINES (COMBINATION METER SUB-ASSEMBLY)
a.

Reconnect the A57 ECM connector.


b.
U154716E02
2.844,2.469 3.052,2.927 false 2.719,2.469 2.333,2.927 false 0.198,0.156 0.438,0.5 0.24,0.344 10 false *a 2.802,2.948 3.26,3.115 0.458,0.167 10 false CANL 2.125,2.958 2.583,3.125 0.458,0.167 10 false CANH 1.677,0.74 1.99,0.906 0.313,0.167 10 false L27

Disconnect the L27 combination meter sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L27-19 (CANH) - L27-20 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to Combination Meter Sub-assembly)



OK

REPLACE COMBINATION METER SUB-ASSEMBLY

NG

4.CHECK FOR OPEN IN CAN BUS LINES (NO. 2 CAN JUNCTION CONNECTOR)
4.CHECK FOR OPEN IN CAN BUS LINES (NO. 2 CAN JUNCTION CONNECTOR)
a.

Reconnect the L27 combination meter sub-assembly connector.


b.
U154776E03
0.99,1.354 1.083,1.354 1.083,1.354 1.552,1.667 false 2.51,1.354 2.042,1.354 2.042,1.354 1.729,1.656 false 1.552,1.865 1.063,2.073 1.063,2.073 0.979,2.073 false 1.75,1.875 1.958,2.063 1.958,2.063 2.521,2.063 false 0.146,0.094 0.698,0.458 0.552,0.365 10 false *a 0.385,1.26 1,1.469 0.615,0.208 10 false CANL*b 2.573,1.271 3.167,1.521 0.594,0.25 10 false CANH*b 1.615,0.615 2.063,0.875 0.448,0.26 10 false L94 0.396,1.969 0.979,2.198 0.583,0.229 10 false CANL*c 2.594,1.969 3.156,2.146 0.563,0.177 10 false CANH*c

Disconnect the L94 wire harness connector from the No. 2 CAN junction connector (instrument panel connector holder left side).


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
L94-2 (CANH) -L94-1 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω No. 3 CAN junction connector
L94-5 (CANH) - L94-4 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω No. 1 CAN junction connector


Text in Illustration
*a Front view of wire harness connector
(to No. 2 CAN Junction Connector)
*b to No. 3 CAN Junction Connector
*c to No. 1 CAN Junction Connector

Result:
Result Proceed to
OK A
NG (Line to No. 1 CAN junction connector) B
NG (Line to No. 3 CAN junction connector) C




A

REPLACE NO. 2 CAN JUNCTION CONNECTOR

B

5.CHECK FOR OPEN IN CAN BUS LINES (NO. 2 CAN JUNCTION CONNECTOR - NO. 1 CAN JUNCTION CONNECTOR)

C

7.CHECK FOR OPEN IN CAN BUS LINES (NO. 3 CAN JUNCTION CONNECTOR)
5.CHECK FOR OPEN IN CAN BUS LINES (NO. 2 CAN JUNCTION CONNECTOR - NO. 1 CAN JUNCTION CONNECTOR)
a.

Reconnect the L94 wire harness connector to the No. 2 CAN junction connector (instrument panel connector holder left side).


b.
U154807E02
2.135,1.75 2.135,0.979 2.135,0.979 2.479,0.979 false 2.125,2.063 2.125,2.542 2.125,2.542 2.49,2.542 false 0.135,0.094 0.396,0.313 0.26,0.219 10 false *a 1.552,0.698 1.969,0.906 0.417,0.208 10 false L132 2.531,0.896 3.198,1.219 0.667,0.323 10 false CANH*b 2.542,2.438 3.208,2.76 0.667,0.323 10 false CANL*b

Disconnect the L132 wire harness connector from the No. 1 CAN junction connector (instrument panel wire side).


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L132-6 (CANH) - L132-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to No. 1 CAN Junction Connector)
*b to No. 2 CAN Junction Connector



OK

6.CHECK FOR OPEN IN CAN BUS LINES (NO. 1 CAN JUNCTION CONNECTOR - ECM)

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 1 CAN JUNCTION CONNECTOR - NO. 2 CAN JUNCTION CONNECTOR)

6.CHECK FOR OPEN IN CAN BUS LINES (NO. 1 CAN JUNCTION CONNECTOR - ECM)
a.
U154808E03
1.25,1.74 1.25,0.969 1.25,0.969 0.917,0.969 false 1.25,2.104 1.25,2.583 1.25,2.583 0.896,2.583 false 0.156,0.146 0.417,0.365 0.26,0.219 10 false *a 1.594,0.781 2.01,0.99 0.417,0.208 10 false A67 0.323,0.875 0.99,1.198 0.667,0.323 10 false CANH*b 0.323,2.49 0.99,2.813 0.667,0.323 10 false CANL*b

Disconnect the A67 wire harness connector from the No. 1 CAN junction connector (engine room main wire side).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A67-1 (CANH) - A67-7 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to No. 1 CAN Junction Connector)
*b to ECM



OK

REPLACE NO. 1 CAN JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 1 CAN JUNCTION CONNECTOR - ECM)

7.CHECK FOR OPEN IN CAN BUS LINES (NO. 3 CAN JUNCTION CONNECTOR)
a.

Reconnect the L94 wire harness connector to the No. 2 CAN junction connector (instrument panel connector holder left side).


b.
U154809E02
1.969,1.75 1.969,0.844 1.969,0.844 2.313,0.844 false 1.958,2.083 1.958,2.74 1.958,2.74 2.313,2.74 false 2.125,1.729 2.125,1.104 2.125,1.104 2.458,1.104 false 2.135,2.083 2.135,2.49 2.135,2.49 2.49,2.49 false 0.115,0.104 0.406,0.354 0.292,0.25 10 false *a 1.531,0.521 1.948,0.729 0.417,0.208 10 false L133 2.365,0.76 3.031,0.958 0.667,0.198 10 false CANH*b 2.365,2.656 3.031,2.979 0.667,0.323 10 false CANL*b 2.531,1.021 3.104,1.219 0.573,0.198 10 false CANH*c 2.531,2.396 3.083,2.563 0.552,0.167 10 false CANL*c

Disconnect the L133 wire harness connector from the No. 3 CAN junction connector (instrument panel wire side).


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
L133-5 (CANH) -L133-11 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω No. 2 CAN junction connector
L133-6 (CANH) - L133-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω Combination meter sub-assembly


Text in Illustration
*a Front view of wire harness connector
(to No. 3 CAN Junction Connector)
*b to No. 2 CAN Junction Connector
*c to Combination Meter Sub-assembly

Result:
Result Proceed to
OK A
NG (Line to No. 2 CAN junction connector) B
NG (Line to Combination meter sub-assembly) C




A

REPLACE NO. 3 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 2 CAN JUNCTION CONNECTOR - NO. 3 CAN JUNCTION CONNECTOR)

C

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 3 CAN JUNCTION CONNECTOR - COMBINATION METER SUB-ASSEMBLY))