There may be an open circuit in one of the CAN main bus lines when the resistance between terminals 18 (CA4H) and 17 (CA4L) of the central gateway ECU (network gateway ECU) is 70 Ω or higher.
| Symptom | Trouble Area |
|---|---|
| Resistance between terminals 18 (CA4H) and 17 (CA4L) of the central gateway ECU (network gateway ECU) is 70 Ω or higher. | ·
CAN main bus lines or connector ·
Central gateway ECU (network gateway ECU) branch line or connector ·
ECM ·
Combination meter sub-assembly ·
No. 1 CAN junction connector ·
No. 2 CAN junction connector ·
No. 3 CAN junction connector |
This malfunction is not related to the lines of a CAN branch or to ECUs or sensors connected to a CAN branch.
Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).
After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
DTC check procedure: Turn the power switch on (IG), turn the cruise control system on using the cruise control switch (ON/OFF switch), wait at least 60 seconds, and then drive the vehicle at a speed of 50 km/h (31 mph) or more for at least 1.72 seconds.
After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSIS SYSTEM).
Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.
When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L192-18 (CA4H) - L192-17 (CA4L) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| *a | Front view of wire harness connector
(to Central Gateway ECU (Network Gateway ECU)) |
When the measured value is 133 Ω or higher and a CAN communication system DTC is output, there may be a fault besides disconnection of the central gateway ECU (network gateway ECU) branch line. For that reason, troubleshooting should be performed again from How to Proceed with Troubleshooting after repairing the trouble area (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).
OK
NG
Disconnect the A57 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A57-13 (CANH) - A57-5 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| *a | Front view of wire harness connector
(to ECM) |
OK
NG
Reconnect the A57 ECM connector.
Disconnect the L27 combination meter sub-assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L27-19 (CANH) - L27-20 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| *a | Front view of wire harness connector
(to Combination Meter Sub-assembly) |
OK
NG
Reconnect the L27 combination meter sub-assembly connector.
Disconnect the L94 wire harness connector from the No. 2 CAN Junction Connector (instrument panel connector holder left side).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| L94-1 (CANH) -L94-2 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω | No. 1 CAN junction connector |
| L94-4 (CANH) - L94-5 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω | No. 3 CAN junction connector |
| *a | Front view of wire harness connector
(to No. 2 CAN Junction Connector) |
| *b | to No. 1 CAN Junction Connector |
| *c | to No. 3 CAN Junction Connector |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Line to No. 3 CAN junction connector) | B |
| NG (Line to No. 1 CAN junction connector) | C |
A
B
C
Reconnect the L94 wire harness connector to the No. 2 CAN Junction Connector (instrument panel connector holder left side).
Disconnect the L133 wire harness connector from the No. 3 CAN Junction Connector (instrument panel wire side).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L133-6 (CANH) - L133-12 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| *a | Front view of wire harness connector
(to No. 3 CAN Junction Connector) |
| *b | to No. 2 CAN Junction Connector |
OK
NG
Disconnect the A68 wire harness connector from the No. 3 CAN Junction Connector (engine room main wire side).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A68-1 (CANH) - A68-7 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| *a | Front view of wire harness connector
(to No. 3 CAN Junction Connector) |
| *b | to ECM |
OK
NG
Reconnect the L94 wire harness connector to the No. 2 CAN Junction Connector (instrument panel connector holder left side).
Disconnect the L132 wire harness connector from the No. 1 CAN Junction Connector (instrument panel wire side).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| L132-5 (CANH) -L132-11 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω | No. 2 CAN junction connector |
| L132-6 (CANH) - L132-12 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω | Combination meter sub-assembly |
| *a | Front view of wire harness connector
(to No. 1 CAN Junction Connector) |
| *b | to No. 2 CAN Junction Connector |
| *c | to Combination Meter Sub-assembly |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Line to No. 2 CAN junction connector) | B |
| NG (Line to combination meter subassembly) | C |
A
B
C