Home › Vehicle Interior › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM › 2012.03–2016.05
RM2070E _58 Vehicle Interior _061937 DOOR LOCK _0301757 POWER DOOR LOCK CONTROL SYSTEM J

DOOR LOCK  POWER DOOR LOCK CONTROL SYSTEM  Only Back Door cannot be Opened  


DESCRIPTION

The main body ECU (multiplex network body ECU) receives signals from the back door opener switch assembly. Then, the main body ECU (multiplex network body ECU) activates the back door lock motor.

WIRING DIAGRAM

B291518E02
4.343,3.511 5.999,3.824 1.656,0.313 10 Main Body ECU (Multiplex Network Body ECU) 1.307,3.132 3.583,3.307 2.276,0.174 10 Back Door Opener Switch Assembly 1.419,2.002 3.066,2.177 1.647,0.174 10 Back Door Lock Assembly 1.307,5.187 3.583,5.362 2.276,0.174 10 Back Door Opener Switch Assembly 1.419,1.815 1.719,1.981 0.299,0.165 10 V11 1.307,2.946 1.583,3.111 0.276,0.165 10 V4 1.307,5.01 1.583,5.175 0.276,0.165 10 V4 5.146,5.645 6.700,6.005 1.554,0.360 10 Certification ECU (Smart Key ECU Assembly) 5.146,5.468 5.413,5.633 0.267,0.165 10 L62 5.01,0.695 5.211,0.860 0.201,0.165 10 L7 4.996,2.712 5.188,2.877 0.192,0.165 10 L7 4.058,1.395 4.269,1.560 0.211,0.165 10 2D 5.151,1.297 5.269,1.462 0.119,0.165 10 6 2.657,1.283 3.035,1.425 0.378,0.142 10 ACT+ 2.849,2.628 3.057,2.770 0.208,0.142 10 UL 1.862,2.628 1.986,2.770 0.125,0.142 10 E 2.837,0.562 3.036,0.704 0.200,0.142 10 D+ 1.487,1.283 1.830,1.425 0.343,0.142 10 ACT- 1.291,1.283 1.398,1.467 0.107,0.184 10 1 3.147,1.283 3.254,1.467 0.107,0.184 10 2 3.147,0.534 3.254,0.717 0.107,0.184 10 3 3.147,2.614 3.254,2.798 0.107,0.184 10 3 1.676,2.614 1.783,2.798 0.107,0.184 10 2 4.107,1.199 4.221,1.364 0.114,0.165 10 9 5.003,0.501 5.194,0.666 0.191,0.165 10 19 5.003,2.504 5.194,2.669 0.191,0.165 10 23 5.046,4.641 5.236,4.806 0.191,0.165 10 22 2.841,4.66 3.049,4.802 0.208,0.142 10 UL 1.853,4.66 1.978,4.802 0.125,0.142 10 E 3.138,4.646 3.246,4.829 0.107,0.184 10 3 1.667,4.646 1.775,4.829 0.107,0.184 10 2 5.319,4.73 5.766,4.879 0.448,0.149 10 TSW5 5.347,0.702 5.794,0.851 0.448,0.149 10 BCTY 5.347,2.733 5.794,2.882 0.448,0.149 10 BDSU 5.347,1.36 5.635,1.509 0.288,0.149 10 TR+ 1.172,2.607 1.362,2.770 0.191,0.163 10 *1 3.974,2.607 4.164,2.770 0.191,0.163 10 *1 6.303,3.78 6.494,3.943 0.191,0.163 10 *2 1.154,4.593 1.345,4.756 0.191,0.163 10 *2 4.096,4.593 4.287,4.756 0.191,0.163 10 *2 0.73,6.327 2.470,6.490 1.739,0.163 10 : CAN Communication Line 0.399,5.652 3.388,5.794 2.989,0.142 10 *1: w/o Entry System Back Door Open Function 0.399,5.987 3.293,6.143 2.894,0.156 10 *2: w/ Entry System Back Door Open Function 3.581,1.764 5.237,2.077 1.656,0.313 10 Instrument Panel Junction Block Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

The power door lock control system uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the power door lock control system after confirming that the communication systems are functioning properly.

·

w/ Entry System Back Door Open Function:

Before performing this troubleshooting. perform troubleshooting for "Back Door Entry Unlock Function does not Operate" for entry and start system (for Entry Function) first (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>Back Door Entry Unlock Function does not Operate).



PROCEDURE

1.SYSTEM CHECK
a.

Check the vehicle specification.

Result:
Result Proceed to
w/o Entry System Back Door Open Function A
w/ Entry System Back Door Open Function B




A

2.CHECK POWER DOOR LOCK OPERATION (BASIC FUNCTION)

B

6.INSPECT BACK DOOR LOCK ASSEMBLY
2.CHECK POWER DOOR LOCK OPERATION (BASIC FUNCTION)
a.

Check the power door lock basic function (See page Vehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK).

OK:

The power door lock basic functions operate normally.




OK

3.READ VALUE USING GTS (DOOR LOCK STATUS)

NG

3.READ VALUE USING GTS (DOOR LOCK STATUS)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.


Main Body (Main Body ECU (Multiplex Network Body ECU))
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Back Door Open Back door lock/Permit or Prohibt Permit: Back door unlocked
Prohibt: Back door locked
-

OK:

The GTS indicates Permit or Prohibit according to the door lock operation shown in the table.



OK

4.PERFORM ACTIVE TEST USING GTS

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

4.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Main Body (Main Body ECU (Multiplex Network Body ECU))
Tester Display Test Part Control Range Diagnostic Note
Trunk and Back-Door Open Operate back door lock motor OFF/ON -

OK:

The back door lock assembly unlatches when ON is selected.




OK

5.READ VALUE USING GTS

NG

6.INSPECT BACK DOOR LOCK ASSEMBLY
5.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Main Body (Main Body ECU (Multiplex Network Body ECU))
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Back Door Open Handle SW Back door opener switch signal/ON or OFF ON: Back door opener switch pushed
OFF: Back door opener switch not pushed
-

OK:

The GTS indicates ON or OFF according to the switch operation shown in the table.




OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

10.INSPECT BACK DOOR OPENER SWITCH ASSEMBLY
6.INSPECT BACK DOOR LOCK ASSEMBLY
a.

Remove the back door lock assembly (See page Vehicle Interior>DOOR LOCK>BACK DOOR LOCK>REMOVAL).

B442018E01
1.646,2.271 1.896,2.271 1.896,2.271 1.896,1.854 false 2.104,2.271 2.104,1.854 false 2.552,2.271 2.302,2.271 2.302,2.271 2.302,1.854 false 0.167,0.125 0.708,0.479 0.542,0.354 10 false *a 1.948,2.323 2.49,2.677 0.542,0.354 10 false ACT+ 1.406,2.177 1.948,2.531 0.542,0.354 10 false D+ 4.719,0.375 5.26,0.729 0.542,0.354 10 false *b 4.75,2.219 5.292,2.573 0.542,0.354 10 false *c 2.615,2.198 3.156,2.552 0.542,0.354 10 false ACT-


b.

Check the operation of the door lock motor.

i.

Move the door lock to the lock position.


ii.

Apply auxiliary battery voltage to the door lock motor and check the operation of the door lock motor.

OK:
Connection Result
Auxiliary battery positive (+) → Terminal 2 (ACT+)
Auxiliary battery negative (-) → Terminal 1 (ACT-)
Unlocks




c.

Check the operation of the door courtesy switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (ACT-) - 3 (D+) Locked 10 kΩ or higher
1 (ACT-) - 3 (D+) Unlocked Below 1 Ω


Text in Illustration
*a Component without harness connected
(Back Door Lock Assembly)
*b Lock
*c Unlock




OK

7.CHECK HARNESS AND CONNECTOR (BACK DOOR LOCK ASSEMBLY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

NG

REPLACE BACK DOOR LOCK ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (BACK DOOR LOCK ASSEMBLY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Disconnect the main body ECU (multiplex network body ECU) connector.


b.

Disconnect the instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V11-2 (ACT+) - 2D-9 (TR+) Always Below 1 Ω
V11-2 (ACT+) - Body ground Always 10 kΩ or higher
V11-3 (D+) - L7-19 (BCTY) Always Below 1 Ω
V11-3 (D+) - Body ground Always 10 kΩ or higher
V11-1 (ACT-) - Body ground Always Below 1 Ω




OK

8.REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Replace the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).



NEXT

9.CHECK BACK DOOR OPEN OPERATION
9.CHECK BACK DOOR OPEN OPERATION
a.

Check that the back door can be opened.

OK:

The back door can be opened normally.




OK

END (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

10.INSPECT BACK DOOR OPENER SWITCH ASSEMBLY
a.
B230875E08
2.292,1.5 2.115,1.917 false 2.354,1.5 2.583,1.917 false 0.26,0.198 0.417,0.375 0.156,0.177 10 false *a 2,1.927 2.24,2.104 0.24,0.177 10 false UL 2.563,1.927 2.76,2.146 0.198,0.219 10 false E

Remove the back door opener switch assembly (See page Vehicle Exterior>DOOR / HATCH>BACK DOOR OPENER SWITCH>REMOVAL).


b.

Check the operation of the opener switch.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (E) - 3 (UL) Back door opener switch not pushed 10 kΩ or higher
2 (E) - 3 (UL) Back door opener switch pushed Below 1 Ω


Text in Illustration
*a Component without harness connected
(Back Door Opener Switch Assembly)



OK

11.CHECK HARNESS AND CONNECTOR (BACK DOOR OPENER SWITCH ASSEMBLY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

NG

REPLACE BACK DOOR OPENER SWITCH ASSEMBLY

11.CHECK HARNESS AND CONNECTOR (BACK DOOR OPENER SWITCH ASSEMBLY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Disconnect the main body ECU (multiplex network body ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V4-3 (UL) - L7-23 (BDSU) Always Below 1 Ω
V4-3 (UL) - Body ground Always 10 kΩ or higher
V4-2 (E) - Body ground Always Below 1 Ω




OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR