Home › Power Source / Network › POWER DISTRIBUTION › MAIN BODY ECU › 2012.03–2013.08
RM2070E _57 Power Source / Network _061935 POWER DISTRIBUTION _0301750 MAIN BODY ECU A

POWER DISTRIBUTION  MAIN BODY ECU  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 7.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 55606 8.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for LHD)

Hide 55480D 9.REMOVE LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY (for LHD)

Hide 55607 10.REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for RHD)

HINT:

Use the same procedure as for LHD (See page Vehicle Interior>INTERIOR PANELS / TRIM>LOWER INSTRUMENT PANEL>REMOVAL).


Hide 55550 11.REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY (for RHD)

HINT:

Use the same procedure as for LHD (See page Vehicle Interior>INTERIOR PANELS / TRIM>LOWER INSTRUMENT PANEL>REMOVAL).


Hide 13.REMOVE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

a.

for LHD:

i.
E190845

Disconnect each connector.


ii.
E190806

Disengage the claw and disconnect the connector as shown in the illustration.


iii.
E190808

Disengage the claw and disconnect the connector as shown in the illustration.


iv.
E190817

Remove the bolt and nut, and disconnect the instrument panel junction block assembly.


v.
E190810

Disengage the 2 claws and disconnect the wiring harness protector.



b.

for RHD:

i.
E190824

Disengage the 2 claws and disconnect the 2 connectors as shown in the illustration.


ii.
E190826

Disconnect each connector.


iii.
E190827

Disengage the clamp.


iv.

Remove the bolt and nut, and disconnect the instrument panel junction block assembly.


v.
E190828

Disengage the clamp.



c.
E190811

Disengage the claw and disconnect the connector as shown in the illustration.


d.
E190813

Disengage the claw and release the connector lock as shown in the illustration.


e.
E190815

Disengage the claw and disconnect the connector, and remove the instrument panel junction block assembly.


Hide 89221 14.REMOVE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

a.
E190836E03
0.375,2.083 0.292,2.74 false 0.667,2.75 0.49,2.094 false 0.219,2.75 0.448,2.958 0.229,0.208 10 false *1 0.583,2.75 0.813,2.958 0.229,0.208 10 false *2

Press the claw of the junction block as shown in the illustration to release the lock.

Text in Illustration
*1 Main Body ECU (Multiplex Network Body ECU)
*2 Claw of Driver Side Junction Block


b.
E190837E02
1.856,2.044 2.749,1.898 false 2.787,1.799 2.997,1.995 0.209,0.196 10 *1

With the junction block lock released, insert a screwdriver with its tip wrapped with protective tape horizontally between the main body ECU (multiplex network body ECU) and junction block.

Text in Illustration
*1 Protective Tape

NOTICE:

Use a screwdriver with a diameter of between 5.0 mm (0.197 in.) and 6.3 mm (0.248 in.) and a length of approximately 90 mm (3.54 in.).



c.
E190838E02
1.718,2.84 1.917,3.031 0.200,0.192 10 *1 0.971,2.643 1.661,2.91 false 3.083,1.759 3.282,1.951 0.200,0.192 10 *1 2.448,2.043 3.026,1.829 false

Using the screwdriver, carefully raise the main body ECU (multiplex network body ECU) up to the position where the connector becomes disengaged.

Text in Illustration
*1 Protective Tape

NOTICE:

Do not twist the screwdriver to raise the main body ECU (multiplex network body ECU).



d.
E190839E04
0.917,1.438 1.104,1.708 0.188,0.271 10 true (1) 2.125,1.604 2.385,1.813 0.26,0.208 10 true (2)

Raise the main body ECU (multiplex network body ECU) as shown by the arrow (1), and then pull it out as shown by the arrow (2) in the illustration.

NOTICE:

Do not touch the ECU connector.