The main body ECU (multiplex network body ECU) receives signals from the back door opener switch assembly. Then, the main body ECU (multiplex network body ECU) activates the back door lock motor.
The power door lock control system uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the power door lock control system after confirming that the communication systems are functioning properly.
w/ Entry System Back Door Open Function:
Before performing this troubleshooting. perform troubleshooting for "Back Door Entry Unlock Function does not Operate" for entry and start system (for Entry Function) first (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>Back Door Entry Lock Function does not Operate).
Check the vehicle specification.
| Result | Proceed to |
|---|---|
| w/o Entry System Back Door Open Function | A |
| w/ Entry System Back Door Open Function | B |
A
B
Check the power door lock basic function (See page Vehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK).
The power door lock basic functions operate normally.
OK
NG
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Main Body / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Back Door Open | Back door lock/Permit or Prohibt | Permit: Back door unlocked
Prohibt: Back door locked |
- |
The GTS indicates Permit or Prohibit according to the door lock operation shown in the table.
OK
NG
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Main Body / Active Test.
Perform the Active Test according to the display on the GTS.
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Trunk and Back-Door Open | Operate back door lock motor | OFF/ON | - |
The back door lock assembly unlatches when ON is selected.
OK
NG
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Main Body / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Back Door Open Handle SW | Back door opener switch signal/ON or OFF | ON: Back door opener switch pushed
OFF: Back door opener switch not pushed |
- |
The GTS indicates ON or OFF according to the switch operation shown in the table.
OK
NG
Remove the back door lock assembly (See page Vehicle Interior>DOOR LOCK>BACK DOOR LOCK>REMOVAL).
Check the operation of the door lock motor.
Move the door lock to the lock position.
Apply auxiliary battery voltage to the door lock motor and check the operation of the door lock motor.
| Connection | Result |
|---|---|
| Auxiliary battery positive (+) → Terminal 2 (ACT+)
Auxiliary battery negative (-) → Terminal 1 (ACT-) |
Unlocks |
Check the operation of the door courtesy switch.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (ACT-) - 3 (D+) | Locked | 10 kΩ or higher |
| 1 (ACT-) - 3 (D+) | Unlocked | Below 1 Ω |
| *a | Component without harness connected
(Back Door Lock Assembly) |
| *b | Lock |
| *c | Unlock |
OK
NG
Disconnect the main body ECU (multiplex network body ECU) connector.
Disconnect the instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| V11-2 (ACT+) - 2D-9 (TR+) | Always | Below 1 Ω |
| V11-2 (ACT+) - Body ground | Always | 10 kΩ or higher |
| V11-3 (D+) - L201-19 (BCTY) | Always | Below 1 Ω |
| V11-3 (D+) - Body ground | Always | 10 kΩ or higher |
| V11-1 (ACT-) - Body ground | Always | Below 1 Ω |
OK
NG
Replace the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).
NEXT
Check that the back door can be opened.
The back door can be opened normally.
OK
NG
Remove the back door opener switch assembly (See page Vehicle Exterior>DOOR / HATCH>BACK DOOR OPENER SWITCH>REMOVAL).
Check the operation of the opener switch.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2 (E) - 3 (UL) | Back door opener switch not pushed | 10 kΩ or higher |
| 2 (E) - 3 (UL) | Back door opener switch pushed | Below 1 Ω |
| *a | Component without harness connected
(Back Door Opener Switch Assembly) |
OK
NG
Disconnect the main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| V4-3 (UL) - L201-23 (BDSU) | Always | Below 1 Ω |
| V4-3 (UL) - Body ground | Always | 10 kΩ or higher |
| V4-2 (E) - Body ground | Always | Below 1 Ω |
OK
NG