Home › Vehicle Interior › DOOR LOCK › FRONT DOOR LOCK › from 2016.05
RM2070E _58 Vehicle Interior _061937 DOOR LOCK _0301761 FRONT DOOR LOCK A

DOOR LOCK  FRONT DOOR LOCK  INSTALLATION  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 69760C 2.INSTALL FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY (w/o Double Locking System)

Hide 69760C 3.INSTALL FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY (w/ Double Locking System)

Hide 69720B 4.INSTALL FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY (w/o Double Locking System)

Hide 69720B 5.INSTALL FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY (w/ Double Locking System)

Hide 69036A 6.INSTALL FRONT DOOR LOCK COVER SUB-ASSEMBLY (w/o Double Locking System)

Hide 69320 7.INSTALL FRONT DOOR LOCK ASSEMBLY

NOTICE:
·

When reusing a removed front door lock assembly, replace the door lock wiring harness seal with a new one.

·

Do not allow grease or dust to adhere to the door lock wiring harness seal installation surface.

·

Reusing a door lock wiring harness seal or using a damaged door lock wiring harness seal may cause water ingress. This may result in a malfunction of the front door lock assembly.



a.

Apply MP grease to the sliding parts of the front door lock assembly.


b.

When reusing the front door lock assembly:

i.

Install a new door lock wiring harness seal to the front door lock assembly.



c.
B387647E04
0.945,1.142 1.189,1.327 0.243,0.185 10 *1 1.254,0.916 1.098,1.158 false

Connect the front door lock open rod to the front door lock assembly.

Text in Illustration
*1 Front Door Lock Open Rod

HINT:

Make sure that the front door lock open rod is securely connected to the front door lock assembly.



d.

Using a T30 "TORX" socket wrench, install the front door lock assembly with the 3 screws.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


e.

Connect the connector.


Hide 8.INSTALL FRONT DOOR OUTSIDE HANDLE COVER WITH LOCK CYLINDER ASSEMBLY (for Driver Side)

Hide 67404F 9.INSTALL FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY

Hide 68151D 10.INSTALL FRONT DOOR GLASS RUN

Hide 68102 11.INSTALL FRONT DOOR GLASS SUB-ASSEMBLY

Hide 67832 12.INSTALL FRONT DOOR SERVICE HOLE COVER

Hide 67626 13.INSTALL FRONT DOOR TRIM BRACKET

Hide 67602 14.INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY

Hide 74222 15.INSTALL DOOR ARMREST COVER

Hide 16.INSTALL MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)

Hide 17.INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)

Hide 69284C 18.INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG

Hide 19.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 25.INITIALIZE POWER WINDOW CONTROL SYSTEM