Home › Vehicle Interior › INTERIOR PANELS / TRIM › ROOF HEADLINING › 2016.05–2017.12
RM2070E _58 Vehicle Interior _061948 INTERIOR PANELS / TRIM _0301860 ROOF HEADLINING A

INTERIOR PANELS / TRIM  ROOF HEADLINING  INSTALLATION  


PROCEDURE

Hide 1.SET ROOF HEADLINING ASSEMBLY

a.
B274296

Put the roof headlining assembly into the vehicle through the front of the vehicle.

NOTICE:

Do not damage the roof headlining assembly or body interior.


HINT:

Temporarily install the roof headlining assembly so that the windshield glass can be installed.



Hide 56111 2.INSTALL WINDSHIELD GLASS

Hide 3.INSTALL ROOF HEADLINING ASSEMBLY (except Glass Roof)

a.

Install the 5 clips.


b.

Remove the protective cover.


c.

w/o Satellite Radio:

i.

Engage the 3 clamps and connect the connector to the front pillar RH.


ii.

Engage the claw and connect the connector to the rear pillar RH.



d.

w/ Satellite Radio:

i.

Engage the 3 clamps and connect the 2 connectors to the front pillar RH.


ii.

Engage the claw and clamp, and connect the 2 connectors to the rear pillar RH.



e.

Engage the 3 clamps and connect the connector to the front pillar LH.


f.

Install the protective cover.


g.

w/ EC Mirror:

i.

Connect the connector.



h.

w/ Rain Sensor:

i.

Connect the connector.



i.

w/ Lane Departure Alert System:

i.

Connect the connector.



Hide 4.INSTALL ROOF HEADLINING ASSEMBLY (for Glass Roof)

a.

Engage the 15 fasteners.


b.

Install the 3 clips.


c.

Remove the protective cover.


d.

w/o Satellite Radio:

i.

Engage the 3 clamps and connect the connector to the front pillar RH.


ii.

Engage the claw and connect the connector to the rear pillar RH.



e.

w/ Satellite Radio:

i.

Engage the 3 clamps and connect the 2 connectors to the front pillar RH.


ii.

Engage the claw and clamp, and connect the 2 connectors to the rear pillar RH.



f.

Engage the 3 clamps and connect the connector to the front pillar LH.


g.

Install the protective cover.


h.

w/ EC Mirror:

i.

Connect the inner rear view mirror connector.



i.

w/ Rain Sensor:

i.

Connect the rain sensor connector.



j.

w/ Lane Departure Alert System:

i.

Connect the connector.



Hide 74348 5.INSTALL VISOR HOLDER

a.
B211698

Engage the 2 claws.


b.

Push in the visor holder as shown in the illustration.

HINT:

Use the same procedure for the other visor holder.



Hide 74320 6.INSTALL VISOR ASSEMBLY LH

a.

Install the visor assembly LH with the 2 screws.


Hide 74310 7.INSTALL VISOR ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 74610S 8.INSTALL FRONT ASSIST GRIP ASSEMBLY

a.
B203057

Assemble the front assist grip assembly as shown in the illustration.


b.
B229265

Install the front assist grip assembly.

HINT:

Use the same procedure for the other front assist grip assembly.



Hide 74620B 9.INSTALL REAR ASSIST GRIP ASSEMBLY

a.
B131970

Assemble the rear assist grip assembly as shown in the illustration.


b.
B229264

Install the rear assist grip assembly.

HINT:

Use the same procedure for the other rear assist grip assembly.



Hide 73139A 10.INSTALL SEAT BELT ANCHOR COVER

a.
B273820

Engage the 2 guides and 2 claws, 2 clips to install the seat belt anchor cover.


Hide 81240 11.INSTALL NO. 1 ROOM LIGHT ASSEMBLY

Hide 81260A 12.INSTALL MAP LIGHT ASSEMBLY (except Glass Roof)

Hide 81260A 13.INSTALL MAP LIGHT ASSEMBLY (for Glass Roof)

Hide 86466A 14.INSTALL NO. 1 LANE RECOGNITION COVER (w/ Lane Departure Alert System)

Hide 86466B 15.INSTALL NO. 2 LANE RECOGNITION COVER (w/ Lane Departure Alert System)

Hide 89943 16.INSTALL RAIN SENSOR COVER (w/ Rain Sensor)

Hide 87818 17.INSTALL INNER REAR VIEW MIRROR COVER (w/ EC Mirror)

Hide 62452C 18.INSTALL REAR ROOF SIDE RAIL GARNISH LH

a.

Engage the guide and 4 claws to install the rear roof side rail garnish LH.


Hide 62480A 19.INSTALL ROOF SIDE INNER GARNISH ASSEMBLY LH

a.

Pass the floor anchor of the rear seat outer seat belt assembly LH through the roof side inner garnish assembly LH.


b.

Insert the roof side inner garnish assembly LH in the direction indicated by the arrow (1) shown in the illustration and engage the 3 clips (B).

B282794E03
2.688,2.156 2.885,2.323 0.198,0.167 10 true (2) 4.167,1.25 4.365,1.417 0.198,0.167 10 false (1) 2.667,1.115 2.875,1.281 0.208,0.167 10 true (A) 3.302,0.854 3.51,1.021 0.208,0.167 10 true (B) 4.271,0.531 4.479,0.698 0.208,0.167 10 false (B) 3.615,0.781 3.823,0.948 0.208,0.167 10 true (B) 2.583,1.458 2.792,1.625 0.208,0.167 10 true (A) 2.823,1.583 3.031,1.75 0.208,0.167 10 false (A) 3.771,1.604 3.979,1.771 0.208,0.167 10 true (A) 4.719,0.938 4.927,1.104 0.208,0.167 10 false (A) 4.083,1.719 4.292,1.885 0.208,0.167 10 true (A) 3.5,1.448 3.708,1.615 0.208,0.167 10 false (A)


c.

Insert the roof side inner garnish assembly LH in the direction indicated by the arrow (2) shown in the illustration and engage the 7 clips (A) to install the roof side inner garnish assembly LH and rear roof side rail garnish LH as a unit.


d.
B282795

Engage the 2 guides.


e.

Engage the 2 claws to install the belt guide LH.


Hide 73570 20.CONNECT REAR NO. 2 SEAT OUTER BELT ASSEMBLY LH (for Upper Side)

Hide 64740C 21.INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH

a.

Engage the 5 guides, 5 clips and 7 claws.

U154626E03
3.365,1.219 3.573,1.094 false 4.063,1.146 4.156,1.542 4.156,1.542 4.469,1.198 false 1.958,0.99 2.406,0.969 false 1.76,0.906 1.969,1.073 0.208,0.167 10 false (A) 3.177,1.146 3.385,1.313 0.208,0.167 10 false (A) 4.063,1.563 4.271,1.729 0.208,0.167 10 true (A)

HINT:

Make sure that the 4 guides (A) of the deck trim side panel assembly LH are inserted securely to prevent any excessive gaps.



b.

Install the deck trim side panel assembly LH with the 2 bolts.


Hide 73570 23.CONNECT REAR NO. 2 SEAT OUTER BELT ASSEMBLY LH (for Lower Side)

Hide 73370C 24.CONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY LH

Hide 55548C 25.INSTALL NO. 2 CUP HOLDER

a.

Engage the 12 claws to install the No. 2 cup holder.


Hide 64713F 26.INSTALL FRONT DECK SIDE TRIM COVER LH

a.
B317540

Engage the 2 guides.


b.

Engage the 2 claws to install the front deck side trim cover LH.


Hide 58460D 27.INSTALL LUGGAGE HOLD BELT STRIKER ASSEMBLY (for LH Side)

a.

Engage the 2 guides.


b.

Install the 2 luggage hold belt striker assemblies with the 2 bolts.


Hide 64721G 28.INSTALL NO. 1 DECK TRIM COVER (for LH Side)

a.
B313173

Engage the 2 guides and 3 claws to install the No. 1 deck trim cover.


Hide 62451C 29.INSTALL REAR ROOF SIDE RAIL GARNISH RH

HINT:

Use the same procedure as for the LH side.


Hide 62471A 30.INSTALL ROOF SIDE INNER GARNISH ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 73560 31.INSTALL REAR NO. 2 SEAT OUTER BELT ASSEMBLY RH (for Upper Side)

HINT:

Use the same procedure as for the LH side.


Hide 64730B 32.INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 73560 33.CONNECT REAR NO. 2 SEAT OUTER BELT ASSEMBLY RH (for Lower Side)

HINT:

Use the same procedure as for the LH side.


Hide 73360C 34.CONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 55548C 35.INSTALL NO. 1 CUP HOLDER

a.

Connect the connector.


b.

Engage the 12 claws to install the No. 1 cup holder.


Hide 64712F 36.INSTALL FRONT DECK SIDE TRIM COVER RH

HINT:

Use the same procedure as for the LH side.


Hide 58460D 37.INSTALL LUGGAGE HOLD BELT STRIKER ASSEMBLY (for RH Side)

HINT:

Use the same procedure as for the LH side.


Hide 64721G 38.INSTALL NO. 1 DECK TRIM COVER (for RH Side)

HINT:

Use the same procedure as for the LH side.


Hide 62412 39.INSTALL CENTER PILLAR GARNISH LH

a.

Pass the floor anchor of the front seat outer seat belt assembly LH through the center pillar garnish LH.


b.

Engage the 2 clips to install the center pillar garnish LH.


c.

Install the center pillar garnish LH with the bolt.


Hide 62414A 40.INSTALL CENTER PILLAR LOWER GARNISH LH

a.

Engage the 4 claws and 2 clips to install the center pillar lower garnish LH.


Hide 73220 41.CONNECT FRONT SEAT OUTER BELT ASSEMBLY LH

Hide 73233 42.INSTALL LAP BELT OUTER ANCHOR COVER (for LH Side)

Hide 62332A 43.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH

a.
B274269E02
2.534,3.22 2.691,3.369 0.157,0.149 10 *a 2.114,3.697 2.32,3.305 2.32,3.305 2.508,3.305 false

Align the alignment mark (Red) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip LH.

Text in Illustration
*a Alignment Mark (Red)

NOTICE:

After installation, check that the corners fit correctly.



Hide 67918A 44.INSTALL REAR DOOR SCUFF PLATE LH

a.

Move the rear seat assembly LH to the foremost position.


b.

Engage the 9 claws and 3 clips to install the rear door scuff plate LH.


Hide 62212 45.INSTALL FRONT PILLAR GARNISH LH

a.

Remove the protective cover.


b.

Engage the front pillar garnish clip to the front pillar garnish LH.

B448128E01
2.942,0.997 3.099,1.146 0.157,0.149 10 *2 2.693,0.475 2.851,0.624 0.157,0.149 10 *1 4.377,0.248 4.534,0.397 0.157,0.149 10 *b 1.294,0.248 1.452,0.397 0.157,0.149 10 *a 2.206,0.697 2.679,0.555 false 2.451,1.218 2.923,1.076 false 6.114,0.997 6.271,1.146 0.157,0.149 10 *2 5.871,0.475 6.029,0.624 0.157,0.149 10 *1 5.384,0.697 5.856,0.555 false 5.624,1.218 6.096,1.076 false

Text in Illustration
*1 Front Pillar Garnish Clip *2 Front Pillar Garnish LH
*a Correct *b Incorrect


c.
B448122E02
2.583,2.844 2.698,2.99 0.115,0.146 10 false B 0.74,1.635 0.854,1.781 0.115,0.146 10 false A 1.729,2.396 1.844,2.542 0.115,0.146 10 false A 1.354,1.573 1.458,1.719 0.104,0.146 10 true 2 2.135,0.802 2.24,0.948 0.104,0.146 10 false 1

Engage the guide (B) in the direction indicated by the arrow (1) shown in the illustration.


d.

Engage the 2 guides (A) in the direction indicated by the arrow (2) shown in the illustration.


e.
B448125

Engage the clip and front pillar garnish clip to install the front pillar garnish LH as shown in the illustration.

HINT:

Make sure that the curtain shield airbag assembly LH is not pinched.



Hide 62312B 46.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

a.
B274268E02
2.515,3.228 2.672,3.377 0.157,0.149 10 *a 2.105,3.698 2.31,3.305 2.31,3.305 2.499,3.305 false

Align the alignment mark (Yellow) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip LH.

Text in Illustration
*a Alignment Mark (Yellow)

NOTICE:

After installation, check that the corners fit correctly.



Hide 62112A 47.INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH

a.

Engage the 2 clips.


b.

Install the cowl side trim sub-assembly LH with the clip.


Hide 67914 48.INSTALL FRONT DOOR SCUFF PLATE LH

a.

Engage the 10 claws to install the front door scuff plate LH.


Hide 62411 49.INSTALL CENTER PILLAR GARNISH RH

HINT:

Use the same procedure as for the LH side.


Hide 62413A 50.INSTALL CENTER PILLAR LOWER GARNISH RH

HINT:

Use the same procedure as for the LH side.


Hide 73210 51.CONNECT FRONT SEAT OUTER BELT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 73233 52.INSTALL LAP BELT OUTER ANCHOR COVER (for RH Side)

HINT:

Use the same procedure as for the LH side.


Hide 62331A 53.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH

a.
B274267E02
0.763,3.223 0.920,3.372 0.157,0.149 10 *a 1.339,3.697 1.133,3.305 1.133,3.305 0.945,3.305 false

Align the alignment mark (Blue) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip RH.

Text in Illustration
*a Alignment Mark (Blue)

NOTICE:

After installation, check that the corners fit correctly.



Hide 67917A 54.INSTALL REAR DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.


Hide 62211 55.INSTALL FRONT PILLAR GARNISH RH

HINT:

Use the same procedure as for the LH side.


Hide 62311B 56.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

a.
B274266E02
0.78,3.233 0.937,3.382 0.157,0.149 10 *a 1.355,3.698 1.15,3.306 1.15,3.306 0.962,3.306 false

Align the alignment mark (White) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip RH.

Text in Illustration
*a Alignment Mark (White)

NOTICE:

After installation, check that the corners fit correctly.



Hide 62111C 57.INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 67913 58.INSTALL FRONT DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.


Hide 72128C 60.INSTALL SEAT TRACK BRACKET COVER LH

Hide 72159H 61.INSTALL REAR SEAT TRACK BRACKET COVER

Hide 72127D 62.INSTALL SEAT TRACK BRACKET COVER RH

Hide 67935A 63.INSTALL BACK DOOR SCUFF PLATE

a.

Engage the 2 guides and 2 claws, 4 clips to install the back door scuff plate.


Hide 64910J 64.INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)

a.

Install the tonneau cover assembly.


Hide 64995 65.INSTALL DECK FLOOR BOX RH

a.

Engage the 3 claws to install the deck floor box RH.


Hide 64993 66.INSTALL REAR DECK FLOOR BOX

a.

Install the rear deck floor box.


Hide 58411A 67.INSTALL NO. 1 DECK BOARD

a.

Install the No. 1 deck board.


Hide 58412A 68.INSTALL NO. 2 DECK BOARD

a.

Install the No. 2 deck board.


Hide 58410B 69.INSTALL DECK BOARD ASSEMBLY

a.

Install the deck board assembly.