Home › Vehicle Interior › DOOR LOCK › REAR DOOR LOCK › 2014.11–2016.05
RM2070E _58 Vehicle Interior _061937 DOOR LOCK _0301762 REAR DOOR LOCK A

DOOR LOCK  REAR DOOR LOCK  INSTALLATION  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 69780B 2.INSTALL REAR DOOR INSIDE LOCKING CABLE ASSEMBLY (w/o Double Locking System)

Hide 69780B 3.INSTALL REAR DOOR INSIDE LOCKING CABLE ASSEMBLY (w/ Double Locking System)

Hide 69740D 4.INSTALL REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY (w/o Double Locking System)

Hide 69740D 5.INSTALL REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY (w/ Double Locking System)

Hide 69038A 6.INSTALL REAR DOOR LOCK COVER SUB-ASSEMBLY (w/o Double Locking System)

Hide 69060A 7.INSTALL REAR DOOR LOCK WITH MOTOR ASSEMBLY

NOTICE:
·

When reusing a removed rear door lock with motor assembly, replace the door lock wiring harness seal with a new one.

·

Do not allow grease or dust to adhere to the door lock wiring harness seal installation surface.

·

Reusing a door lock wiring harness seal or using a damaged door lock wiring harness seal may cause water ingress. This may result in a malfunction of the rear door lock with motor assembly.



a.

Apply MP grease to the sliding parts of the rear door lock with motor assembly.


b.

When reusing the rear door lock with motor assembly:

i.

Install a new door lock wiring harness seal to the rear door lock with motor assembly.



c.
B387656E06
2.958,2.323 3.125,2.198 true 3.125,2.083 3.302,2.24 0.177,0.156 10 true *a

Connect the rear door lock with motor assembly to the release plate of the rear door outside handle frame sub-assembly, and set it to the rear door panel.

Text in Illustration
*a Release Plate

HINT:

Make sure that the release plate of the rear door outside handle frame sub-assembly is securely connected to the rear door lock with motor assembly



d.

Using a T30 "TORX" socket wrench, install the rear door lock with motor assembly with the 3 screws.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 68104 8.INSTALL REAR DOOR GLASS SUB-ASSEMBLY

Hide 67488C 9.INSTALL REAR DOOR REAR GUIDE SEAL

Hide 67872 10.CONNECT REAR DOOR WEATHERSTRIP

a.

Connect the rear door weatherstrip.


Hide 67408D 11.INSTALL REAR DOOR WINDOW GUIDE SUB-ASSEMBLY

Hide 68152C 12.INSTALL REAR DOOR GLASS RUN

Hide 67842E 13.INSTALL REAR DOOR SERVICE HOLE COVER

Hide 67628 14.INSTALL REAR DOOR TRIM BRACKET

Hide 67604 15.INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY

Hide 74262 16.INSTALL REAR DOOR ARMREST COVER

Hide 17.INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL

Hide 69284D 18.INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG

Hide 19.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 25.INITIALIZE POWER WINDOW CONTROL SYSTEM