If the entry lock and unlock functions do not operate for the driver door only, the request code may not be being transmitted from the driver door or the front door outside handle assembly (for driver door) (touch sensor) may be malfunctioning. If the entry functions for other doors operate properly, communication between the electrical key transmitter sub-assembly and door control receiver is normal. In this case, there may be a problem with request code transmission (communication between the certification ECU (smart key ECU assembly) and front door outside handle assembly (for driver door) [driver door electrical key antenna]), or there may be wave interference.
The entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.
When using the GTS with the power switch off to troubleshoot:
Connect the GTS to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the GTS and vehicle begins.
Check that there are no electrical key transmitter sub-assemblies in the vehicle.
Before performing the inspection, check that DTC B1242 (wireless door lock control) is not output (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>DTC CHECK / CLEAR).
Before replacing the certification ECU (smart key ECU assembly), refer to the Service Bulletin.
After repair, confirm DTC not reoccur with performing the "DTC Output Confirmation Operation".
When the door control switch on the multiplex network master switch assembly is operated, check that the doors unlock and lock according to the switch operation (See page Vehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK).
Door locks operate normally.
OK
NG
(See pageVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING)
Bring the electrical key transmitter sub-assembly approximately 0.3 m (0.98 ft.) from the front door outside handle assembly (for driver door) and perform an entry function check (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).
| *A | for LHD |
| *B | for LHD |
| *a | Approximately 0.3 m (0.98 ft.) |
If the electrical key transmitter sub-assembly is brought within 0.2 m (0.66 ft.) of the door handle, communication may not possible.
If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of electric wave interference is high. Also, added vehicle components may cause electric wave interference. If installed, remove them and perform the operation check.
| Result | Proceed to |
|---|---|
| Entry function does not operate normally. | A |
| Entry function operates normally. | B |
A
B
Disconnect the n1*1 or m1*2 front door outside handle assembly (for driver door) connector.
Disconnect the L62 certification ECU (smart key ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.
*1: for LHD
*2: for RHD
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| n1-3 (ANT2) - L62-4 (CG1B) | Always | Below 1 Ω |
| n1-6 (ANT1) - L62-3 (CLG1) | Always | Below 1 Ω |
| n1-5 (B) - L62-32 (POS1) | Always | Below 1 Ω |
| n1-2 (GND) - Body ground | Always | Below 1 Ω |
| n1-3 (ANT2) or L62-4 (CG1B) - Body ground | Always | 10 kΩ or higher |
| n1-6 (ANT1) or L62-3 (CLG1) - Body ground | Always | 10 kΩ or higher |
| n1-5 (B) or L62-32 (POS1) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| m1-3 (ANT2) - L62-4 (CG1B) | Always | Below 1 Ω |
| m1-6 (ANT1) - L62-3 (CLG1) | Always | Below 1 Ω |
| m1-5 (B) - L62-32 (POS1) | Always | Below 1 Ω |
| m1-2 (GND) - Body ground | Always | Below 1 Ω |
| m1-3 (ANT2) or L62-4 (CG1B) - Body ground | Always | 10 kΩ or higher |
| m1-6 (ANT1) or L62-3 (CLG1) - Body ground | Always | 10 kΩ or higher |
| m1-5 (B) or L62-32 (POS1) - Body ground | Always | 10 kΩ or higher |
OK
NG
Disconnect the n1*1 or m1*2 front door outside handle assembly (for driver door) connector.
Connect the L62 certification ECU (smart key ECU assembly) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| n1-5 (B) - Body ground*1
m1-5 (B) - Body ground*2 |
Power switch off → on (IG) | 9 to 12 V → Below 2 V |
Using an oscilloscope, check the waveform.
| Tester Connection | Condition | Tool Setting | Specified Condition |
|---|---|---|---|
| n1-3 (ANT2) - n1-6 (ANT1)*1
m1-3 (ANT2) - m1-6 (ANT1)*2 |
Procedure:
1.
Power switch off 2.
Key brought outside vehicle 3.
All doors closed 4.
Key not inside vehicle 5.
All doors locked through wireless operation |
2 V/DIV., 500 ms/DIV. | Pulse generation (See waveform) |
*1: for LHD
*2: for RHD
| *A | for LHD |
| *B | for RHD |
| *1 | Waveform |
| *a | Front view of wire harness connector
(to Front Door Outside Handle Assembly (for driver door)) |
OK
NG
Temporarily replace the front door outside handle assembly (for driver door) with a new or normally functioning one (See page Vehicle Exterior>DOOR / HATCH>FRONT DOOR>DISASSEMBLY).
NEXT
Check that the entry functions operate normally (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).
Entry functions operate normally.
OK
NG