Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.
1. PRECAUTION
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
58410B
2.REMOVE DECK BOARD ASSEMBLY
58411A
3.REMOVE NO. 1 DECK BOARD
58412A
4.REMOVE NO. 2 DECK BOARD
64993
5.REMOVE REAR DECK FLOOR BOX
64995
6.REMOVE DECK FLOOR BOX RH
7.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
69284C
8.REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG
Using a moulding remover, disengage the 3 claws and remove the front door inside handle bezel plug.
9.REMOVE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)
Using a moulding remover, disengage the clip, 11 claws and 4 guides.
Disconnect the connector and remove the multiplex network master switch assembly with front door armrest base panel.
10.REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)
Using a moulding remover, disengage the clip, 11 claws and 4 guides.
Disconnect the connector and remove the power window regulator switch assembly with front door armrest base panel.
74222
11.REMOVE DOOR ARMREST COVER
Remove the door armrest cover.
67602
12.REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY
Put protective tape around the front door panel.
| *1 | Protective Tape |
Remove the 2 screws.
Using a clip remover, disengage the 9 clips.
Disconnect the courtesy light connector.
Make sure not to damage the courtesy light and harness.
Pull out the front door trim board sub-assembly in the direction indicated by the arrow in the illustration.
Raise the front door trim board sub-assembly and disconnect the front door trim board sub-assembly with the front door inner glass weatherstrip.
Disconnect the front door lock remote control cable assembly and front door inside locking cable assembly, and remove the front door trim board sub-assembly.
68172A
13.REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP
Disengage the 7 claws and remove the front door inner glass weatherstrip from the front door trim board sub-assembly as shown in the illustration.
69206B
14.REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY
Using a screwdriver, disengage the 2 claws to remove the front door inside handle sub-assembly.
81230
15.REMOVE COURTESY LIGHT ASSEMBLY
87912A
16.REMOVE OUTER MIRROR PROTECTOR
87964
17.REMOVE OUTER MIRROR INSTALL HOLE COVER
18.REMOVE OUTER REAR VIEW MIRROR ASSEMBLY WITH COVER
86160
19.REMOVE FRONT NO. 1 SPEAKER ASSEMBLY
67626
20.REMOVE FRONT DOOR TRIM BRACKET
Remove the 2 screws and front door trim bracket.
67832
21.REMOVE FRONT DOOR SERVICE HOLE COVER
Remove the front door service hole cover.
Remove any remaining butyl tape from the front door panel.
68102
22.REMOVE FRONT DOOR GLASS SUB-ASSEMBLY
Remove the grommet.
Connect the cable to the negative (-) auxiliary battery terminal and multiplex network master switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.
Disconnect the cable from the negative (-) auxiliary battery terminal and multiplex network master switch assembly.
Remove the 2 bolts.
After the bolts are removed, do not allow the door glass to fall.
Remove the front door glass sub-assembly as indicated by the arrows, in the order shown in the illustration.
Do not damage the door glass.
23.REMOVE FRONT DOOR POWER WINDOW REGULATOR ASSEMBLY
Disconnect the connector.
Loosen the temporary bolt.
| *1 | Temporary Bolt |
Do not remove the temporary bolt. If the temporary bolt is removed, the front door power window regulator assembly may fall and cause damage.
Remove the 5 bolts and front door power window regulator assembly.
Remove the temporary bolt from the front door power window regulator assembly.
85720D
24.REMOVE POWER WINDOW REGULATOR MOTOR ASSEMBLY
Using a T25 "TORX" socket wrench, remove the 3 screws and power window regulator motor assembly.
68151D
25.REMOVE FRONT DOOR GLASS RUN
Remove the front door glass run.
67404F
26.REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY
Remove the bolt.
Disengage the guide and front door rear lower frame sub-assembly as shown in the illustration.
27.REMOVE FRONT DOOR OUTSIDE HANDLE COVER WITH LOCK CYLINDER ASSEMBLY (for Driver Side)
Remove the hole plug.
Using a T30 "TORX" socket wrench, loosen the screw and remove the front door outside handle cover with lock cylinder assembly.
The screw cannot be removed because it is integrated into the front door outside handle frame sub-assembly.
69217D
28.REMOVE FRONT DOOR OUTSIDE HANDLE COVER (for Driver Side)
Using a screwdriver, disengage the claw and 2 guides to remove the front door outside handle cover as shown in the illustration.
69217D
29.REMOVE FRONT DOOR OUTSIDE HANDLE COVER (for Front Passenger Side)
Remove the hole plug.
Using a T30 "TORX" socket wrench, loosen the screw and remove the front door outside handle cover.
The screw cannot be removed because it is integrated into the front door outside handle frame sub-assembly.
69220
30.REMOVE FRONT DOOR OUTSIDE HANDLE ASSEMBLY
w/ Entry and Start System:
Using a screwdriver, disengage the 2 claws.
Using a screwdriver, disconnect the connector.
Move the lever in the direction indicated by the arrow in the illustration.
Remove the front door outside handle assembly as shown in the illustration.
69241H
31.REMOVE FRONT DOOR FRONT OUTSIDE HANDLE PAD
Disengage the 3 claws to remove the front door front outside handle pad.
69242E
32.REMOVE FRONT DOOR REAR OUTSIDE HANDLE PAD
Disengage the 2 claws to remove the front door rear outside handle pad.
69320
33.REMOVE FRONT DOOR LOCK ASSEMBLY
Disconnect the connector.
| *1 | Front Door Lock Open Rod |
Using a T30 "TORX" socket wrench, remove the 3 screws.
Slide the front door lock assembly downward to disconnect the front door lock open rod and remove the front door lock assembly and cables as a unit.
When reusing the front door lock assembly:
Remove the door lock wiring harness seal from the front door lock assembly.
69036A
34.REMOVE FRONT DOOR LOCK COVER SUB-ASSEMBLY (w/o Double Locking System)
Using a screwdriver, disengage the 2 claws as shown in the illustration.
Disengage the 2 claws to remove the front door lock cover sub-assembly.
69720B
35.REMOVE FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY (w/o Double Locking System)
Remove the front door lock remote control cable assembly as shown in the illustration.
69720B
36.REMOVE FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY (w/ Double Locking System)
Remove the front door lock remote control cable assembly as shown in the illustration.
69760C
37.REMOVE FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY (w/o Double Locking System)
Remove the front door inside locking cable assembly as shown in the illustration.
69760C
38.REMOVE FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY (w/ Double Locking System)
Using a screwdriver, disengage the 3 claws as shown in the illustration.
Remove the front door inside locking cable assembly as shown in the illustration.
69202A
39.REMOVE FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY
w/ Entry and Start System:
Disconnect the connector.
Disengage the clamp.
Using a T30 "TORX" socket wrench, loosen the screw.
| *a | Outside |
| *b | Inside |
Slide the front door outside handle frame sub-assembly to disengage the door handle nut and claw of the front door outside handle frame sub-assembly, and then remove it.
82152A
40.REMOVE FRONT DOOR WIRE (w/ Entry and Start System)
Disengage the 2 clamps and remove the front door wire.
69312
41.REMOVE FRONT DOOR LOCK OPEN ROD
Remove the front door lock open rod as indicated by the arrows, in the order shown in the illustration.
67664C
42.REMOVE DOOR FRAME GARNISH
Using a screwdriver with its tip wrapped with protective tape, disengage the clip to remove the door frame garnish.
This garnish needs to be replaced with a new one because the clip will break when removing the door frame garnish.
68620
43.REMOVE FRONT DOOR CHECK ASSEMBLY
Remove the 3 bolts and front door check assembly.
67862
44.REMOVE FRONT DOOR WEATHERSTRIP
Using a clip remover, disengage the 17 clips and remove the front door weatherstrip.
67001A
45.REMOVE FRONT DOOR PANEL CUSHION
Disengage the 2 claws to remove the 2 front door panel cushions.
75720
46.REMOVE FRONT DOOR BELT MOULDING ASSEMBLY
75756C
47.REMOVE FRONT DOOR REAR WINDOW FRAME MOULDING
75922M
48.REMOVE NO. 1 BLACK OUT TAPE
75986B
49.REMOVE FRONT DOOR STRIPE
75976G
50.REMOVE FRONT DOOR LOWER OUTSIDE STRIPE
75966B
51.REMOVE FRONT DOOR REAR OUTSIDE STRIPE