If the entry lock function does not operate for the front passenger door only, but the entry unlock function operates, the request code is being transmitted properly from the front passenger door. In this case, there may be a problem related to the front door outside handle assembly (for front passenger door) (lock sensor) (connection between the certification ECU (smart key ECU assembly) and front door outside handle assembly (for front passenger door) [lock sensor]).
The entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.
When using the GTS with the power switch off to troubleshoot:
Connect the GTS to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the GTS and vehicle begins.
Check that there are no electrical key transmitter sub-assemblies in the vehicle.
Before performing the inspection, check that DTC B1242 (wireless door lock control) is not output (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>DTC CHECK / CLEAR).
Before replacing the certification ECU (smart key ECU assembly), refer to the Service Bulletin.
After repair, confirm DTC not reoccur with performing the "DTC Output Confirmation Operation".
When the door control switch on the multiplex network master switch assembly is operated, check that the doors unlock and lock according to the switch operation (See page Vehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK).
Door locks operate normally.
OK
NG
(See pageVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING)
Using the GTS, read the Data List (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>DATA LIST / ACTIVE TEST).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| P-Door Trigger Switch | Front passenger door touch sensor (lock sensor) / ON or OFF | ON: Front passenger door touch sensor (lock sensor) touched
OFF: Front passenger door touch sensor (lock sensor) not touched |
·
Displays whether the lock sensor is on or off (even if the sensor is touched and contact is maintained, "ON" is displayed only momentarily). ·
Use this Data List item to help determine if there is a lock sensor malfunction when the entry lock function does not operate. |
The GTS display changes correctly in response to the operation of the front door outside handle assembly (for front passenger door).
OK
NG
Disconnect the m1*1 or n1*2 front door outside handle assembly (for front passenger door) connector.
Disconnect the L62 certification ECU (smart key ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.
*1: for LHD
*2: for RHD
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| m1-1 (TRG+) - L62-19 (TSW2) | Always | Below 1 Ω |
| L62-15 (E) - Body ground | Always | Below 1 Ω |
| m1-1 (TRG+) or L62-19 (TSW2) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| n1-1 (TRG+) - L62-19 (TSW2) | Always | Below 1 Ω |
| L62-15 (E) - Body ground | Always | Below 1 Ω |
| n1-1 (TRG+) or L62-19 (TSW2) - Body ground | Always | 10 kΩ or higher |
OK
NG
Connect the m1*1 or n1*2 front door outside handle assembly (for front passenger door) connector.
*1: for LHD
*2: for RHD
| *1 | Waveform | - | - |
| *a | Component with harness connected
(Certification ECU (smart key ECU assembly)) |
*b | In actuality, sampling is being performed |
Connect the L62 certification ECU (smart key ECU assembly) connector.
Using an oscilloscope, check the waveform.
| Tester Connection | Condition | Tool Setting | Specified Condition |
|---|---|---|---|
| L62-19 (TSW2) - L62-15 (E) | Procedure:
1.
Power switch off 2.
Key brought outside vehicle 3.
All doors closed 4.
Front passenger door lock sensor not touched → touched |
2 V/DIV., 500 ms/DIV. | Pulse generation (See waveform) |
OK
NG