Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Entry Function) › 2014.11–2016.05
RM2070E _58 Vehicle Interior _061938 THEFT DETERRENT / KEYLESS ENTRY _0301767 ENTRY AND START SYSTEM(for Entry Function) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Entry Function)  All Door Entry Lock/Unlock Functions and Wireless Functions do not Operate  


DESCRIPTION

When the entry operation and wireless operation of the door lock functions do not operate, a malfunction or wave interference may be occurring in either of the following: 1) the signal communication line between the door control receiver and certification ECU (smart key ECU assembly) (the line used for entry and wireless operations); or 2) the electrical key transmitter sub-assembly. If the entry lock and wireless lock operations cannot be performed, there may be electrical key transmitter sub-assembly malfunctions, wave interference or problems in the communication which is used for the entry and wireless function between the door control receiver and certification ECU (smart key ECU assembly).

WIRING DIAGRAM

B250087E11
5.51,0.315 5.923,0.489 0.413,0.174 10 CUTB 4.434,0.439 4.902,0.613 0.468,0.174 10 ECU-B 2.479,0.312 3.832,0.486 1.353,0.174 10 from Auxiliary Battery 4.398,0.919 4.938,1.093 0.539,0.174 10 ECU-B2 5.156,0.315 5.441,0.489 0.285,0.174 10 L62 5.196,0.128 5.376,0.302 0.181,0.174 10 17 5.51,1.782 5.923,1.956 0.413,0.174 10 RDA 5.156,1.782 5.441,1.956 0.285,0.174 10 L63 5.196,1.595 5.376,1.769 0.181,0.174 10 15 5.51,2.271 5.923,2.444 0.413,0.174 10 RSSI 5.156,2.271 5.441,2.444 0.285,0.174 10 L63 5.196,2.083 5.376,2.257 0.181,0.174 10 16 5.51,2.786 5.923,2.960 0.413,0.174 10 E 5.156,2.786 5.441,2.960 0.285,0.174 10 L62 5.071,3.114 6.617,3.431 1.546,0.317 10 Certification ECU (Smart Key ECU Assembly) 1.032,3.011 1.394,3.185 0.362,0.174 10 S12 1.032,3.189 2.494,3.363 1.461,0.174 10 Door Control Receiver 5.196,2.599 5.376,2.773 0.181,0.174 10 15 5.51,0.793 5.740,0.967 0.230,0.174 10 +B 5.156,0.793 5.441,0.967 0.285,0.174 10 L62 5.231,0.598 5.331,0.772 0.099,0.174 10 1 5.51,1.283 5.852,1.457 0.342,0.174 10 RCO 2.093,1.283 2.269,1.457 0.176,0.174 10 +5 2.377,1.199 2.553,1.373 0.176,0.174 10 4 1.899,1.782 2.291,1.956 0.392,0.174 10 DATA 2.377,1.695 2.553,1.869 0.176,0.174 10 5 1.915,2.271 2.287,2.444 0.372,0.174 10 RSSI 2.377,2.188 2.553,2.362 0.176,0.174 10 2 1.915,2.702 2.287,2.876 0.372,0.174 10 GND 2.377,2.63 2.553,2.804 0.176,0.174 10 1 5.156,1.283 5.441,1.457 0.285,0.174 10 L63 5.231,1.087 5.331,1.261 0.099,0.174 10 5

CAUTION / NOTICE / HINT

NOTICE:
·

The entry and start system (for Entry Function) uses the CAN communication system and LIN communication system. First inspect the communication systems by following How to Proceed with Troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

·

When using the GTS with the power switch off to troubleshoot:

Connect the GTS to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the GTS and vehicle begins.

·

Check that there are no electrical key transmitter sub-assemblies in the vehicle.

·

Before performing the inspection, check that DTC B1242 (wireless door lock control) is not output (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>DTC CHECK / CLEAR).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

Before replacing the certification ECU (smart key ECU assembly) or electrical key transmitter sub-assembly (key), refer to the Service Bulletin.

·

After repair, confirm DTC not reoccur with performing the "DTC Output Confirmation Operation".

·

Door control receiver has a constant voltage (5 V) supply circuit connected to terminal "+5".



PROCEDURE

1.INSPECT AUXILIARY BATTERY VOLTAGE
a.

Measure the voltage of the auxiliary battery with the power switch off.

Standard voltage:

11 to 14 V


HINT:

It may be possible to tell whether the auxiliary battery is depleted by operating the horn.


If the voltage is below 11 V, recharge or replace the auxiliary battery before proceeding.




NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Open the driver door using the mechanical key built into the electrical key transmitter sub-assembly.


b.

Connect the GTS and check for DTCs (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>DTC CHECK / CLEAR).

HINT:

When using the GTS with the power switch off to troubleshoot: Connect the GTS to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the GTS and vehicle begins.


OK:

DTC is not output.




OK

3.CHECK POWER DOOR LOCK CONTROL SYSTEM

NG

3.CHECK POWER DOOR LOCK CONTROL SYSTEM
a.

When the door control switch on the multiplex network master switch assembly on the driver door is operated, check that the doors unlock and lock according to the switch operation (See page Vehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK).

OK:

Door locks operate normally.




OK

4.CHECK ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY

NG

4.CHECK ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY
a.

When another registered electrical key transmitter sub-assembly is used, check that the wireless and entry functions operate normally (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).

Result
Result Proceed to
Entry function operates A
Entry function does not operate B



A

5.CHECK ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY (LED)

B

7.CHECK WAVE ENVIRONMENT
5.CHECK ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY (LED)
a.

Press and hold the lock switch of the transmitter for 5 seconds and check the number of times that the transmitter LED illuminates.

Result
Result Proceed to
Transmitter LED does not illuminate when switch is pressed and held A
Transmitter LED illuminates 3 times or more when switch is pressed and held B
Transmitter LED illuminates once or twice but not third time C

HINT:
·

The electrical key transmitter sub-assembly sends voltage information to the certification ECU (smart key ECU assembly) when it is being used. The certification ECU (smart key ECU assembly) displays "Yes" for the "Key Low Battery" item of the Data List when this voltage information indicates 2.1 V or less (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>DATA LIST / ACTIVE TEST).

·

Even if the transmitter battery is depleted, it is still possible to start the hybrid control system by holding the electrical key transmitter sub-assembly against the power switch, depressing the brake pedal and pressing the power switch.





A

6.INSPECT TRANSMITTER BATTERY (VOLTAGE)

B

REPLACE ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY

C

REPLACE TRANSMITTER BATTERY

6.INSPECT TRANSMITTER BATTERY (VOLTAGE)
a.

Inspect the transmitter battery (for Type A)

i.
B232800E01
0.917,0.357 1.128,0.534 0.211,0.177 10 *1 1.604,1.87 1.604,0.43 1.604,0.43 1.084,0.43 false

Remove the transmitter battery from the electrical key transmitter sub-assembly that does not operate (See page Vehicle Interior>DOOR LOCK>TRANSMITTER BATTERY>REPLACEMENT).


ii.

Attach a lead wire (0.60 mm [0.0236 in.] in diameter or less including wire sheath) with tape or equivalent to the negative terminal.

Text in Illustration
*1 Lead Wire

NOTICE:

Do not wrap the lead wire around a terminal, wedge it between terminals, or solder it. The terminal may be deformed or damaged, and the transmitter battery will not be able to be installed correctly.



iii.

Carefully pull the lead wire out from the position shown in the illustration and install the previously removed transmitter battery.


iv.
B286799E01
1.821,0.278 2.116,0.475 0.295,0.198 12 *1 0.933,1.217 1.243,0.37 1.243,0.37 1.776,0.37 false

Measure the voltage of the transmitter battery.

HINT:
·

When measuring the transmitter battery voltage, bring the electrical key transmitter sub-assembly within the lock entry operating range while operating the lock sensor of a door handle to perform the measurement. For the entry lock operating range, refer to System Description (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>SYSTEM DESCRIPTION).

·

Perform the measurement when the electrical key transmitter sub-assembly is at room temperature.

·

The electrical key transmitter sub-assembly sends voltage information to the certification ECU (smart key ECU assembly) when it is transmitting. When this voltage is 2.1 V or less the Data List item "Key Low Battery" displays "Yes".



Text in Illustration
*1 GND

Standard Voltage:
Tester Connection Condition Specified Condition
Transmitter battery positive (+) - Transmitter battery negative (-) Power switch off, all doors closed and lock sensor touched 2.2 to 3.2 V





OK

REPLACE ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY

NG

REPLACE TRANSMITTER BATTERY

7.CHECK WAVE ENVIRONMENT
a.

Bring the electrical key transmitter sub-assembly near the door control receiver and perform a wireless and entry function operation check.

HINT:
·

When the electrical key transmitter sub-assembly is brought near the door control receiver, the possibility of electric wave interference decreases, and it can be determined if electric wave interference is causing the problem symptom.

·

If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.

·

There may be electric wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.

·

If a tool for checking electric waves, such as a signal strength meter, is available, move around the area while observing both the LF band (used by the vehicle antenna to form the key detection area) and RF band (used by the electrical key transmitter sub-assembly for transmission) to check for locations where there is wave interference.



OK:

Wireless and entry functions operate normally.




OK

AFFECTED BY WAVE INTERFERENCE

NG

8.CHECK POWER SOURCE
8.CHECK POWER SOURCE
a.

When the power source mode is off, check that the functions other than the entry functions recognize the power source mode as being off.

HINT:
·

Check if systems that should not be operating when the power source mode is off are operating.

·

When the certification ECU (smart key ECU assembly) mistakenly determines the power source mode to be on (IG) for some reason (example: an ECU mistakenly determines the power source mode to be on (IG) and sends that information to the certification ECU (smart key ECU assembly)) even though the power source mode is off, the certification ECU (smart key ECU assembly) stops the entry and wireless functions.



OK:

When the power source mode is off, functions other than the entry functions recognize the power source mode as being off.




OK

9.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - AUXILIARY BATTERY AND BODY GROUND)

NG

9.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - AUXILIARY BATTERY AND BODY GROUND)
a.
U154535E02
0.583,1.469 0.365,1.104 0.365,1.104 0.26,1.104 false 2.896,1.479 3.083,1.177 3.083,1.177 3.198,1.177 false 0.698,1.729 0.594,2 0.594,2 0.49,2 false 0.094,0 0.313,0.188 0.219,0.188 10 false *a 1.625,0.719 1.927,0.875 0.302,0.156 10 false L62 0.104,1.917 0.563,2.135 0.458,0.219 10 false CUTB 0.063,1.021 0.26,1.167 0.198,0.146 10 false +B 3.229,1.104 3.365,1.281 0.135,0.177 10 false E

Disconnect the L62 ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L62-17 (CUTB) - Body ground Power switch off 11 to 14 V
L62-1 (+B) - Body ground Power switch off 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L62-15 (E) - Body ground Always Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to Certification ECU (smart key ECU assembly))


OK

10.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - CERTIFICATION ECU AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - CERTIFICATION ECU AND BODY GROUND)
a.

Disconnect the S12 door control receiver connector.


b.

Disconnect the L63 certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S12-4 (+5) - L63-5 (RCO) Always Below 1 Ω
S12-5 (DATA) - L63-15 (RDA) Always Below 1 Ω
S12-2 (RSSI) - L63-16 (RSSI) Always Below 1 Ω
S12-1 (GND) - Body ground Always Below 1 Ω
S12-4 (+5) or L63-5 (RCO) - Body ground Always 10 kΩ or higher
S12-5 (DATA) or L63-15 (RDA) - Body ground Always 10 kΩ or higher
S12-2 (RSSI) or L63-16 (RSSI) - Body ground Always 10 kΩ or higher


HINT:

For the waveforms between the certification ECU (smart key ECU assembly) and door control receiver when the electrical key transmitter sub-assembly is operated, refer to Terminals of ECU (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>TERMINALS OF ECU).




OK

11.CHECK DOOR CONTROL RECEIVER (OPERATION)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK DOOR CONTROL RECEIVER (OPERATION)
a.

Temporarily replace the door control receiver with a new or normally functioning one (See page Vehicle Interior>DOOR LOCK>DOOR CONTROL RECEIVER(w/o Tire Pressure Warning System)>REMOVAL).


b.

Check that the wireless and entry functions operate normally.

OK:

Wireless and entry functions operate normally.




OK

END (DOOR CONTROL RECEIVER WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)