Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Entry Function) › 2012.03–2014.11
RM2070E _58 Vehicle Interior _061938 THEFT DETERRENT / KEYLESS ENTRY _0301767 ENTRY AND START SYSTEM(for Entry Function) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Entry Function)  All Door Entry Lock/Unlock Functions do not Operate, but Wireless Functions Operate  


DESCRIPTION

When the wireless operation can be used to lock and unlock the doors, communication between the door control receiver and certification ECU (smart key ECU assembly) is normal. If the entry lock and unlock functions do not operate, the entry cancel function may be set through the customize function, there may be communication problems between the electrical key transmitter sub-assembly and vehicle, or there may be electric wave interference.

CAUTION / NOTICE / HINT

NOTICE:
·

The entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

·

When using the GTS with the power switch off to troubleshoot:

Connect the GTS to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the GTS and vehicle begins.

·

Check that there are no electrical key transmitter sub-assemblies in the vehicle.

·

Before performing the inspection, check that DTC B1242 (wireless door lock control) is not output (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>DTC CHECK / CLEAR).

·

Before replacing the certification ECU (smart key ECU assembly) or electrical key transmitter sub-assembly (key), refer to the Service Bulletin.

·

After repair, confirm DTC not reoccur with performing the "DTC Output Confirmation Operation".



PROCEDURE

1.READ VALUE USING GTS (KEY CANCEL SWITCH)
a.

Using the GTS, read the Data List (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>DATA LIST / ACTIVE TEST).

Entry&Start
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Auto Entry Cancel SW Entry cancel function setting / OFF or ON Mode status displayed
ON: entry and start system canceled
OFF: entry and start system not canceled
The default setting for the entry cancel function is OFF. If the customer requests that the entry and start system functions (locking and unlocking the doors while carrying the electrical key transmitter sub-assembly, etc.) be canceled, the setting can be changed through the customize function (See page (Click here)).

Result
Result Proceed to
Entry door lock function cancel is OFF A
Entry door lock function cancel is ON B



A

2.CHECK WAVE ENVIRONMENT

B

2.CHECK WAVE ENVIRONMENT
a.

Move the electrical key transmitter sub-assembly as described below and perform the operation inspection (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).

HINT:
·

When the electrical key transmitter sub-assembly is brought near the front door outside handle assembly (for driver door) or electrical key antenna, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.

·

The transmitting wave of the wireless function and entry function are the same, but the wave logic is different. As a result, it is possible that only the wireless function or only the entry function is affected by wave interference.



i.
B309707E01
0.18,0.147 0.391,0.312 0.210,0.165 10 *A 0.18,2.244 0.391,2.409 0.210,0.165 10 *B 1.95,1.213 2.161,1.378 0.210,0.165 10 *a 1.95,1.213 2.161,1.378 0.210,0.165 10 *a 1.589,3.568 1.800,3.732 0.210,0.165 10 *a

Bring the electrical key transmitter sub-assembly approximately 0.3 m (0.98 ft.) from the front door outside handle assembly (for driver door) and perform a driver door entry lock and unlock operation check.

Text in Illustration
*A for LHD
*B for RHD
*a Approximately 0.3 m (0.98 ft.)

NOTICE:

If the electrical key transmitter sub-assembly is brought within 0.2 m (0.66 ft.) of the door handle, communication may not possible.



ii.
B309710E01
0.172,0 0.429,0.201 0.257,0.201 10 *A 1.599,1.281 1.856,1.482 0.257,0.201 10 *a 1.943,3.498 2.199,3.699 0.257,0.201 10 *a 0.172,2.312 0.429,2.513 0.257,0.201 10 *B

Bring the electrical key transmitter sub-assembly approximately 0.3 m (0.98 ft.) from the front door outside handle assembly (for front passenger door) and perform a front passenger door entry lock and unlock operation check.

Text in Illustration
*A for LHD
*B for RHD
*a Approximately 0.3 m (0.98 ft.)

NOTICE:

If the electrical key transmitter sub-assembly is brought within 0.2 m (0.66 ft.) of the door handle, communication may not possible.



iii.
B274775E01
1.797,1.457 1.946,1.606 0.149,0.149 10 *a

Bring the electrical key transmitter sub-assembly approximately 0.3 m (0.98 ft.) from the electrical key antenna (outside luggage) and perform an entry back door lock and unlock function check.

Text in Illustration
*a Approximately 0.3 m (0.98 ft.)

NOTICE:

If the electrical key transmitter sub-assembly is brought within 0.2 m (0.66 ft.) of the rear bumper, communication may not possible.


HINT:
·

If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.

·

If electric wave interference seems to be the likely cause of the problem, ask the customer if the problem occurs in specific locations.

·

Move the vehicle to a different location, perform the following procedure and check if the symptoms can be reproduced.

·

If a tool for checking electric waves, such as a signal strength meter, is available, move around the area while observing both the LF band (used by the vehicle antenna to form the electrical key transmitter sub-assembly detection area) and RF band (used by the electrical key transmitter sub-assembly for transmission) to check for locations where there is wave interference.



Result
Result Proceed to
All operation checks fail A
All checks are normal B
Some operation checks are normal C




A

3.CHECK ELECTRICAL KEY ANTENNAS IN KEY DIAGNOSTIC MODE

B

AFFECTED BY WAVE INTERFERENCE

C

GO TO OTHER PROBLEM (PROCEED TO PROBLEM SYMPTOMS TABLE FOR EACH DOOR)

3.CHECK ELECTRICAL KEY ANTENNAS IN KEY DIAGNOSTIC MODE
a.

Check the following antennas in the key diagnostic mode (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>SYSTEM DESCRIPTION).

i.
B309707E01
0.18,0.147 0.391,0.312 0.210,0.165 10 *A 0.18,2.244 0.391,2.409 0.210,0.165 10 *B 1.95,1.213 2.161,1.378 0.210,0.165 10 *a 1.95,1.213 2.161,1.378 0.210,0.165 10 *a 1.589,3.568 1.800,3.732 0.210,0.165 10 *a

Check the electrical key antenna (for driver door):

Text in Illustration
*A for LHD
*B for RHD
*a 0.7 to 1 m (2.30 to 3.28 ft.)

When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the front door outside handle assembly (for driver door), check that the wireless door lock buzzer sounds.


ii.
B309710E01
0.172,0 0.429,0.201 0.257,0.201 10 *A 1.599,1.281 1.856,1.482 0.257,0.201 10 *a 1.943,3.498 2.199,3.699 0.257,0.201 10 *a 0.172,2.312 0.429,2.513 0.257,0.201 10 *B

Check the electrical key antenna (for front passenger door):

Text in Illustration
*A for LHD
*B for RHD
*a 0.7 to 1 m (2.30 to 3.28 ft.)

When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the front door outside handle assembly (for front passenger door), check that the wireless door lock buzzer sounds.


iii.
B274772E01
1.838,1.189 2.515,0.488 2.515,0.488 2.832,0.488 false 2.858,0.392 3.038,0.555 0.180,0.163 10 *a

Check the No. 1 indoor electrical key antenna (front floor):

Text in Illustration
*a Inspection Point

When the electrical key transmitter sub-assembly is at the inspection point, check that the wireless door lock buzzer sounds.


iv.
B274773E01
1.862,0.938 2.333,0.466 2.333,0.466 2.603,0.466 false 2.635,0.365 2.852,0.518 0.217,0.152 10 *a

Check the No. 3 indoor electrical key antenna (rear floor):

Text in Illustration
*a Inspection Point

When the electrical key transmitter sub-assembly is at the inspection point, check that the wireless door lock buzzer sounds.


v.
B274774E01
1.649,1.028 2.243,0.434 2.243,0.434 2.566,0.434 false 2.56,0.335 2.737,0.512 0.177,0.177 10 *a

Check the No. 2 indoor electrical key antenna (inside luggage):

Text in Illustration
*a Inspection Point

When the electrical key transmitter sub-assembly is at the inspection point, check that the wireless door lock buzzer sounds.


vi.
B274775E01
1.797,1.457 1.946,1.606 0.149,0.149 10 *a

Check the electrical key antenna (outside luggage):

Text in Illustration
*a 0.7 to 1 m (2.30 to 3.28 ft.)

When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the electrical key antenna (outside luggage), check that the wireless door lock buzzer sounds.

OK:

Wireless door lock buzzer sounds.


Result
Result Proceed to
All diagnostic mode inspections fail A
Some diagnostic mode inspections fail (door) B
Some diagnostic mode inspections fail (interior) C
Some diagnostic mode inspections fail (back door) D
All diagnostic mode inspections are normal E




A

4.INSPECT ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY

B

GO TO OTHER FLOWCHART (PROCEED TO PROBLEM SYMPTOM FLOWCHART FOR EACH DOOR)

C

D

E

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

4.INSPECT ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY
a.

Check if there is another electrical key transmitter sub-assembly available that is already registered to the vehicle.

Result
Result Proceed to
Another registered electrical key transmitter sub-assembly is not available A
Another registered electrical key transmitter sub-assembly is available B



A

5.REPLACE ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY

B

6.CHECK OPERATION
5.REPLACE ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY
a.

Register a new electrical key transmitter sub-assembly.

HINT:

Refer to the Service Bulletin.




NEXT

6.CHECK OPERATION
6.CHECK OPERATION
a.

Check the operation of the entry lock function (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).

OK:

Entry lock function operates normally.




OK

END (ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)