When the wireless operation can be used to lock and unlock the doors, communication between the door control receiver and certification ECU (smart key ECU assembly) is normal. If the entry lock and unlock functions do not operate, the entry cancel function may be set through the customize function, there may be communication problems between the electrical key transmitter sub-assembly and vehicle, or there may be wave interference.
The entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.
When using the GTS with the power switch off to troubleshoot:
Connect the GTS to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the GTS and vehicle begins.
Check that there are no electrical key transmitter sub-assemblies in the vehicle.
Before performing the inspection, check that DTC B1242 (wireless door lock control) is not output (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>DTC CHECK / CLEAR).
Before replacing the certification ECU (smart key ECU assembly) or electrical key transmitter sub-assembly, refer to the entry and start system (for Entry Function) precaution (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>PRECAUTION).
After repair, confirm that no DTCs are output by performing the "DTC Output Confirmation Operation".
Check for DTCs (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>DTC CHECK / CLEAR).
DTC is not output.
OK
NG
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Entry&Start / Data List.
Read the Data List according to the display on the GTS.
If the Data List cannot be read, check the value by performing manual operation of the customize function. (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>CUSTOMIZE PARAMETERS)
| Result | Proceed to |
|---|---|
| Entry door lock function cancel is OFF | A |
| Entry door lock function cancel is ON | B |
A
B
Move the electrical key transmitter sub-assembly as described below and perform the operation inspection (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).
When the electrical key transmitter sub-assembly is brought near the front door outside handle assembly (for driver door) or electrical key antenna, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.
The transmitting wave of the wireless function and entry function are the same, but the wave logic is different. As a result, it is possible that only the wireless function or only the entry function is affected by wave interference.
Bring the electrical key transmitter sub-assembly approximately 0.3 m (0.984 ft.) from the front door outside handle assembly (for driver door) and perform a driver door entry lock and unlock operation check.
| *A | for LHD |
| *B | for RHD |
| *a | Approximately 0.3 m (0.984 ft.) |
If the electrical key transmitter sub-assembly is brought within 0.2 m (0.656 ft.) of the door handle, communication may not be possible.
Bring the electrical key transmitter sub-assembly approximately 0.3 m (0.984 ft.) from the front door outside handle assembly (for front passenger door) and perform a front passenger door entry lock and unlock operation check. (w/ Entry Function)
| *A | for LHD |
| *B | for RHD |
| *a | Approximately 0.3 m (0.984 ft.) |
If the electrical key transmitter sub-assembly is brought within 0.2 m (0.656 ft.) of the door handle, communication may not be possible.
Bring the electrical key transmitter sub-assembly approximately 0.3 m (0.984 ft.) from the electrical key antenna (outside luggage) and perform a luggage compartment door open function check. (w/ Entry Function)
| *a | Approximately 0.3 m (0.984 ft.) |
If the electrical key transmitter sub-assembly is brought within 0.2 m (0.656 ft.) of the rear bumper, communication may not be possible.
If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.
If wave interference seems to be the likely cause of the problem, ask the customer if the problem occurs in specific locations.
Move the vehicle to a different location, perform the following procedure and check if the symptoms can be reproduced.
If a tool for checking electric waves, such as a signal strength meter, is available, move around the area while observing both the LF band (used by the vehicle antenna to form the detection area) and RF band (used by the electrical key transmitter sub-assembly for transmission) to check for locations where there is wave interference.
| Result | Proceed to |
|---|---|
| All operation checks fail | A |
| All operation checks are normal | B |
| Some operation checks are normal | C |
A
B
C
Check the following antennas in the key diagnostic mode (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).
If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter cannot be detected by channel 2 due to a malfunction, such as wave interference.
Check the electrical key antenna (for driver door):
| *A | for LHD |
| *B | for RHD |
| *a | 0.7 to 1 m (2.30 to 3.28 ft.) |
When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the front door outside handle assembly (for driver door), check that the wireless door lock buzzer sounds.
Check the electrical key antenna (for front passenger door): (w/ Entry Function)
| *A | for LHD |
| *B | for RHD |
| *a | 0.7 to 1 m (2.30 to 3.28 ft.) |
When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the front door outside handle assembly (for front passenger door), check that the wireless door lock buzzer sounds.
Check the No. 1 indoor electrical key antenna (front floor):
| *a | Inspection Point |
When the electrical key transmitter sub-assembly is at the inspection point, check that the wireless door lock buzzer sounds.
Check the No. 3 indoor electrical key antenna (rear floor):
| *a | Inspection Point |
When the electrical key transmitter sub-assembly is at the inspection point, check that the wireless door lock buzzer sounds.
Check the No. 2 indoor electrical key antenna (inside luggage):
| *a | Inspection Point |
When the electrical key transmitter sub-assembly is at the inspection point, check that the wireless door lock buzzer sounds.
Check the electrical key antenna (outside luggage): (w/ Entry Function)
| *a | 0.7 to 1 m (2.30 to 3.28 ft.) |
When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the electrical key antenna (outside luggage), check that the wireless door lock buzzer sounds.
Wireless door lock buzzer sounds.
| Result | Proceed to |
|---|---|
| All diagnostic mode inspections fail | A |
| Some diagnostic mode inspections fail (door) | B |
| Some diagnostic mode inspections fail (interior) | C |
| Some diagnostic mode inspections fail (Back door) | D |
| All diagnostic mode inspections are normal | E |
A
B
C
D
E
Check if there is another electrical key transmitter sub-assembly available that is already registered to the vehicle.
| Result | Proceed to |
|---|---|
| Another registered electrical key transmitter sub-assembly is not available | A |
| Another registered electrical key transmitter sub-assembly is available | B |
A
B
Register a new electrical key transmitter sub-assembly.
Refer to the Service Bulletin.
NEXT
Check the operation of the entry lock function (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).
Entry lock function operates normally.
OK
NG