Use these procedures to troubleshoot the entry and start system (for Entry Function).
*: Use the GTS.
| Proceed to |
|---|
| NEXT |
NEXT
In troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.
Gather as much information as possible for reference. Past problems that seem unrelated may also help in some cases.
The following 5 items are important points for problem analysis:
| What? | Vehicle model, system name |
| When? | Date, time, occurrence frequency. Does it occur recently or for a long time? |
| Where? | Does it occur at specified place? |
| Under what conditions? | Unlock/lock the door, power switch on (IG), hybrid control system start. |
| How did it happen? | Problem symptoms* |
*: Be sure to ask the customer in detail about the following points concerning the vehicle operating conditions, environment and problem, and then check for DTCs.
If the entry lock/unlock function does not operate for all doors.
If the entry lock function does not operate.
If the entry unlock function does not operate.
If both the entry lock and unlock functions do not operate.
If the wireless lock and unlock functions do not operate.
If there is no power even when the power switch is pressed (does not turn on (ACC)).
If the hybrid control system does not start with the push-button start function.
If the outside warning buzzers do not sound.
If a hybrid control system start was attempted by holding the electrical key transmitter sub-assembly near the power switch and then pressing the power switch.
If the interior warning buzzers do not sound.
Any other details concerning the problem.
If it is suspected that wave interference is likely, be sure to ask the customer in detail about the following points concerning the vehicle operating conditions, environment and problem.
Specific locations where the system does not operate (such as near TV towers, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc.).
Specific times when the system does not operate: If the symptoms occurred immediately after purchase or only recently. If the symptoms occurred when the electrical key transmitter sub-assembly was near the vehicle (electrical key antenna).
If the system does not operate only when near specific vehicles (there may be wave interference from the wireless systems of other vehicles).
If the system operates intermittently.
If the electrical key transmitter sub-assembly is bundled together with other items.
If the electrical key transmitter sub-assembly is carried together with other electronic devices, such as cell phones, personal computers, portable music players, other electrical key transmitter sub-assemblies, etc. (keep the electrical key transmitter sub-assembly at least 0.1 m (0.328 ft.) away from such items).
Where the electrical key transmitter sub-assembly is being kept when not in use: If the electrical key transmitter sub-assembly being placed within 1 m (3.28 ft.) of items such as TVs, DVD recorders, induction cookers, rice cookers, dishwashers, modems, cell phones, personal computers, microwave ovens, desk or floor lamps, cordless telephones, etc.
If there are electronic devices that transmit radio waves placed in the vehicle.
When the transmitter battery was last replaced. The transmitter battery can be checked roughly using the "Key Low Battery" item in the Data List (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>DATA LIST / ACTIVE TEST).
If the gearshift control does not unlock.
If the customer installed any optional components (theft deterrent devices, wireless fog lights, etc.) to the vehicle.
| Proceed to |
|---|
| NEXT |
NEXT
Measure the vehicle auxiliary battery voltage with the power switch off.
11 to 14 V
If the voltage is below 11 V, recharge or replace the vehicle auxiliary battery before proceeding to the next step.
| Proceed to |
|---|
| NEXT |
NEXT
Using the GTS, check for CAN communication system DTCs (w/o Central gateway ECU: See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>DIAGNOSIS SYSTEM, w/ Central gateway ECU: See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSIS SYSTEM).
| Result | Proceed to |
|---|---|
| CAN DTCs are not output | A |
| CAN DTCs are output (w/o Central gateway ECU) | B |
| CAN DTCs are output ((w/ Central gateway ECU) | C |
A
B
C
Use the GTS to check if the meter/gauge system is functioning normally (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).
If the certification ECU (smart key ECU assembly) mistakenly receives a vehicle speed signal, communication between the vehicle and the GTS fails. Be sure to check "Vehicle Speed Meter" displayed on the Data List to make sure that the vehicle speed is not abnormal.
| Result | Proceed to |
|---|---|
| No vehicle speed signal is mistakenly received. | A |
| A vehicle speed signal is mistakenly received. | B |
A
B
(See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING)
Using the GTS, check for LIN communication system DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| LIN DTCs are not output | A |
| LIN DTCs are output | B |
A
B
(See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING)
Using the GTS, check for wireless door lock control system DTCs (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| Wireless door lock control system DTCs are not output | A |
| Wireless door lock control system DTCs are output | B |
A
B
(See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING)
Check for DTCs (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>DTC CHECK / CLEAR)
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| Electronic shift lever system DTCs are output | B |
| Engine immobiliser system DTCs are output | C |
| Entry and start system (for Entry Function) DTCs are output | D |
A
B
C
D
Refer to Problem Symptoms Table (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>PROBLEM SYMPTOMS TABLE).
| Result | Proceed to |
|---|---|
| Fault is not listed in problem symptoms table | A |
| Fault is listed in problem symptoms table | B |
A
B
Operation Check (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).
Check Data List / Active Test (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>DATA LIST / ACTIVE TEST).
Terminals of ECU (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>TERMINALS OF ECU).
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| Entry and Start System (for Entry Function) DTCs are output | B |
A
B