Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Entry Function) › 2014.11–2016.05
RM2070E _58 Vehicle Interior _061938 THEFT DETERRENT / KEYLESS ENTRY _0301767 ENTRY AND START SYSTEM(for Entry Function) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Entry Function)  B27A1  Open in Driver Side Electrical Antenna Circuit  


DESCRIPTION

The certification ECU (smart key ECU assembly) generates a request signal and transmits the signal to the front door outside handle assembly (for driver door) [electrical key antenna] at intervals of 250 ms. For the front door outside handle assembly (for driver door) [electrical key antenna] to detect when the electrical key transmitter sub-assembly is brought close to the vehicle, a signal requesting a response from the electrical key transmitter sub-assembly is transmitted within approximately 1 m (3.28 ft.) of the driver door at intervals of 250 ms. DTC B27A1 is stored by the certification ECU (smart key ECU assembly) when an open circuit is detected between the certification ECU (smart key ECU assembly) and front door outside handle assembly (for driver door) [electrical key antenna] (between terminals CLG1 and ANT1, or terminals CG1B and ANT2).

DTC Code DTC Detection Condition Trouble Area DTC Output Confirmation Operation
B27A1 An open circuit is detected in the circuit between the certification ECU (smart key ECU assembly) and front door outside handle assembly (for driver door) (CLG1 - ANT1, CG1B - ANT2) (This is detected by the malfunction detection circuit in the certification ECU (smart key ECU assembly)) (1 trip detection logic*).
·

Harness or connector

·

Front door outside handle assembly (for driver door)

·

Certification ECU (smart key ECU assembly)


Any time

*: Only output while a malfunction is present.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Entry lock/unlock operation cannot be performed for driver door -

Related Data List and Active Test
DTC Code Data List and Active Test
B27A1 Key diagnostic mode can be used to perform troubleshooting

WIRING DIAGRAM

B249951E91
1.198,0.323 1.583,0.479 0.385,0.156 10 false ANT1 1.188,0.781 1.583,0.938 0.396,0.156 10 false ANT2 0.24,3.042 1,3.198 0.76,0.156 10 false n1*1, m1*2 1.24,2.615 1.583,2.76 0.344,0.146 10 false GND 3.229,3.042 4.479,3.188 1.25,0.146 10 false *1: for LHD 3.229,3.354 4.479,3.5 1.25,0.146 10 false *2: for RHD 1.667,0.677 1.771,0.833 0.104,0.156 10 false 3 1.677,2.531 1.781,2.688 0.104,0.156 10 false 2 1.667,0.229 1.771,0.375 0.104,0.146 10 false 6 5.646,0.323 6.063,0.49 0.417,0.167 10 false CLG1 5.646,0.781 6.073,0.938 0.427,0.156 10 false CG1B 5.646,2.615 5.823,2.781 0.177,0.167 10 false E 5.448,0.208 5.563,0.365 0.115,0.156 10 false 3 5.448,0.677 5.573,0.844 0.125,0.167 10 false 4 1.448,1.24 1.583,1.396 0.135,0.156 10 false B 1.177,1.698 1.573,1.854 0.396,0.156 10 false SENS 1.667,1.594 1.771,1.75 0.104,0.156 10 false 4 1.667,1.146 1.771,1.292 0.104,0.146 10 false 5 5.656,1.24 6.073,1.406 0.417,0.167 10 false POS1 5.646,1.698 6.073,1.854 0.427,0.156 10 false SEN1 5.365,1.125 5.542,1.281 0.177,0.156 10 false 32 5.365,1.604 5.552,1.771 0.188,0.167 10 false 20 1.188,2.167 1.583,2.323 0.396,0.156 10 false TRG+ 1.667,2.063 1.771,2.219 0.104,0.156 10 false 1 5.646,2.167 6.073,2.323 0.427,0.156 10 false TSW1 5.365,2.063 5.552,2.229 0.188,0.167 10 false 18 5.365,2.531 5.563,2.698 0.198,0.167 10 false 15 5.292,2.958 5.594,3.115 0.302,0.156 10 false L62 5.292,3.135 6.885,3.531 1.594,0.396 10 false Certification ECU (Smart Key ECU Assembly) 0.24,3.188 1.958,3.563 1.719,0.375 10 false Front Door Outside Handle Assembly (for Driver Door)

CAUTION / NOTICE / HINT

NOTICE:
·

The entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

·

When using the GTS with the power switch off to troubleshoot:

Connect the GTS to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the GTS and vehicle begins.

·

Before replacing the certification ECU (smart key ECU assembly), refer to the Service Bulletin.

·

After repair, confirm DTC not reoccur with performing the "DTC Output Confirmation Operation".

·

Front door outside handle assembly (for driver door) has an antenna coil between ANT1 and ANT2 terminals.



PROCEDURE

1.CHECK CONNECTOR CONNECTION
a.

Turn the power switch off.


b.

Check that the connectors are properly connected to the certification ECU (smart key ECU assembly) and front door outside handle assembly (for driver door).

OK:

Connectors are properly connected.




OK

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - FRONT DOOR OUTSIDE HANDLE)

NG

CONNECT CONNECTORS PROPERLY

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - FRONT DOOR OUTSIDE HANDLE)
a.

Disconnect the L62 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the n1*1 or m1*2 front door outside handle assembly (for driver door) connector.


c.

Measure the resistance according to the value(s) in the table below.

*1: for LHD

*2: for RHD


Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
L62-3 (CLG1) - n1-6 (ANT1) Always Below 1 Ω
L62-4 (CG1B) - n1-3 (ANT2) Always Below 1 Ω
L62-15 (E) - Body ground Always Below 1 Ω
n1-2 (GND) - Body ground Always Below 1 Ω
L62-3 (CLG1) or n1-6 (ANT1) - Body ground Always 10 kΩ or higher
L62-4 (CG1B) or n1-3 (ANT2) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
L62-3 (CLG1) - m1-6 (ANT1) Always Below 1 Ω
L62-4 (CG1B) - m1-3 (ANT2) Always Below 1 Ω
L62-15 (E) - Body ground Always Below 1 Ω
m1-2 (GND) - Body ground Always Below 1 Ω
L62-3 (CLG1) or m1-6 (ANT1) - Body ground Always 10 kΩ or higher
L62-4 (CG1B) or m1-3 (ANT2) - Body ground Always 10 kΩ or higher




OK

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO DRIVER SIDE ELECTRICAL KEY ANTENNA)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO DRIVER SIDE ELECTRICAL KEY ANTENNA)
a.

Connect the L62 certification ECU (smart key ECU assembly) connector.

U154569E02
0.417,1.031 0.563,1.031 0.563,1.031 0.833,1.427 false 2.729,0.917 2.583,0.917 2.583,0.917 2.292,1.427 false 2.448,0.719 2.302,0.719 2.302,0.719 2.208,1.427 false 0.094,0.104 0.354,0.354 0.26,0.25 10 false *a 4.479,0.042 4.74,0.292 0.26,0.25 10 false *1 4.354,0.813 4.688,1.01 0.333,0.198 10 false GND 4.354,2.469 4.688,2.667 0.333,0.198 10 false GND 4.479,1.667 4.74,1.917 0.26,0.25 10 false *2 0.302,0.958 0.427,1.156 0.125,0.198 10 false E 2.479,0.635 2.875,0.833 0.396,0.198 10 false CG1B 1.469,0.854 1.771,1.052 0.302,0.198 10 false L62 2.76,0.844 3.156,1.042 0.396,0.198 10 false CLG1

Text in Illustration
*1 Waveform 1 *2 Waveform 2
*a Component with harness connected
(Certification ECU (smart key ECU assembly))
- -


b.

Connect the n1*1 or m1*2 front door outside handle assembly (for driver door) connector.


c.

Using an oscilloscope, check the waveform.

*1: for LHD

*2: for RHD


OK:
Tester Connection Condition Tool Setting Specified Condition
L62-3 (CLG1) - L62-15 (E) Procedure:
1.

Power switch off

2.

Key brought outside vehicle

3.

All doors closed

4.

Key not inside vehicle

5.

Key brought inside detection area*3

6.

All doors locked through wireless operation


2 V/DIV., 500 ms/DIV. Pulse generation (See waveform 1)
L62-3 (CLG1) - L62-15 (E) Procedure:
1.

Power switch off

2.

Key brought outside vehicle

3.

All doors closed

4.

Key not inside vehicle

5.

Key brought outside detection area*4

6.

All doors locked through wireless operation


2 V/DIV., 500 ms/DIV. Pulse generation (See waveform 2)
L62-4 (CG1B) - L62-15 (E) Procedure:
1.

Power switch off

2.

Key brought outside vehicle

3.

All doors closed

4.

Key not inside vehicle

5.

Key brought outside detection area*4

6.

All doors locked with key


2 V/DIV., 500 ms/DIV. Pulse generation (See waveform 2)


*3: For details about the areas that are inside the entry function detection area, refer to Operation Check (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).

*4: For details about the areas that are outside the entry function detection area, refer to Operation Check (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).




OK

4.REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR DRIVER DOOR)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

4.REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR DRIVER DOOR)
a.

Temporarily replace the front door outside handle assembly (for driver door) with a new or normally functioning one (See page Vehicle Exterior>DOOR / HATCH>FRONT DOOR>DISASSEMBLY).



NEXT

5.CLEAR DTC
6.CHECK FOR DTC

OK

END (FRONT DOOR OUTSIDE HANDLE ASSEMBLY WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)