Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Entry Function) › from 2016.05
RM2070E _58 Vehicle Interior _061938 THEFT DETERRENT / KEYLESS ENTRY _0301767 ENTRY AND START SYSTEM(for Entry Function) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Entry Function)  B27A7  Open in Inside Luggage Compartment Electrical Key Oscillator Circuit  


DESCRIPTION

The certification ECU (smart key ECU assembly) generates a request signal and transmits the signal to the No. 2 indoor electrical key antenna assembly (inside luggage). For the No. 2 indoor electrical key antenna assembly (inside luggage) to detect when the electrical key transmitter sub-assembly is inside the vehicle, the signal from the certification ECU (smart key ECU assembly) requesting a response from the electrical key transmitter sub-assembly is transmitted inside the vehicle. DTC B27A7 is stored by the certification ECU (smart key ECU assembly) when an open circuit is detected between the certification ECU (smart key ECU assembly) and No. 2 indoor electrical key antenna assembly (inside luggage) (between terminals CLG7 and ANTE7, or terminals CG7B and CLGB).

DTC Code DTC Detection Condition Trouble Area DTC Output Confirmation Operation
B27A7 An open circuit is detected in the circuit between the certification ECU (smart key ECU assembly) and No. 2 indoor electrical key antenna assembly (inside luggage) (CLG7 - ANTE7, CG7B - CLGB) (1 trip detection logic*).
·

Wire harness or connector

·

No. 2 indoor electrical key antenna assembly (inside luggage)

·

Certification ECU (smart key ECU assembly)


Any time

*: Only output while a malfunction is present.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
When electrical key transmitter sub-assembly is in rear seat area:
·

Power source mode does not change when power switch pressed

·

Electrical key transmitter sub-assembly locked inside vehicle


-

Related Data List and Active Test
DTC Code Data List and Active Test
B27A7 Key diagnostic mode can be used to perform troubleshooting

WIRING DIAGRAM

B441775E08
1.115,0.448 1.604,0.604 0.49,0.156 10 false ANTE7 1.177,0.906 1.573,1.063 0.396,0.156 10 false CLGB 0.104,1.323 0.406,1.479 0.302,0.156 10 false S26 1.667,0.802 1.771,0.958 0.104,0.156 10 false 3 1.667,0.344 1.771,0.49 0.104,0.146 10 false 1 5.625,0.438 6.042,0.604 0.417,0.167 10 false CLG7 5.625,0.896 6.052,1.052 0.427,0.156 10 false CG7B 5.615,1.375 5.792,1.542 0.177,0.167 10 false E 5.354,0.26 5.531,0.417 0.177,0.156 10 false 9 5.354,0.719 5.542,0.885 0.188,0.167 10 false 8 5.313,1.188 5.51,1.354 0.198,0.167 10 false 11 5.292,1.823 6.854,2.208 1.563,0.385 10 false Certification ECU (Smart Key ECU Assembly) 0.104,1.49 2.938,1.938 2.833,0.448 10 false No. 2 Indoor Electrical Key Antenna Assembly (Inside Luggage) 5.25,0.448 5.583,0.615 0.333,0.167 10 false L196 5.24,0.906 5.573,1.073 0.333,0.167 10 false L196 5.24,1.365 5.573,1.531 0.333,0.167 10 false L195

CAUTION / NOTICE / HINT

NOTICE:
·

The entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

·

When using the GTS with the power switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start (CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>PRECAUTION

·

Before replacing the certification ECU (smart key ECU assembly), refer to the entry and start system (for Entry Function) precaution (See page ).

·

After repair, confirm that no DTCs are output by performing the "DTC Output Confirmation Operation".

·

The No. 2 indoor electrical key antenna assembly (inside luggage) has an antenna coil between ANTE7 and CLGB terminals.



PROCEDURE

1.CHECK CONNECTOR CONNECTION
a.

Turn the power switch off.


b.

Check that the connectors are properly connected to the certification ECU (smart key ECU assembly) and No. 2 indoor electrical key antenna assembly (inside luggage).

OK:

Connectors are properly connected.




OK

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - NO. 2 INDOOR ELECTRICAL KEY ANTENNA)

NG

CONNECT CONNECTORS PROPERLY

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - NO. 2 INDOOR ELECTRICAL KEY ANTENNA)
a.

Disconnect the L195 and L196 certification ECU (smart key ECU assembly) connectors.


b.

Disconnect the S26 No. 2 indoor electrical key antenna assembly (inside luggage) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L196-9 (CLG7) - S26-1 (ANTE7) Always Below 1 Ω
L196-8 (CG7B) - S26-3 (CLGB) Always Below 1 Ω
L195-11 (E) - Body ground Always Below 1 Ω
L196-9 (CLG7) or S26-1 (ANTE7) - Body ground Always 10 kΩ or higher
L196-8 (CG7B) or S26-3 (CLGB) - Body ground Always 10 kΩ or higher




OK

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 2 INDOOR ELECTRICAL KEY ANTENNA)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 2 INDOOR ELECTRICAL KEY ANTENNA)
a.

Connect the L195 and L196 certification ECU (smart key ECU assembly) connectors.

U190854E02
3.792,1.385 4.146,2.188 true 3.708,1.385 3.354,2.188 true 2.708,1.51 2.438,2.188 true 1.208,2.771 1.417,2.969 0.208,0.198 10 false *1 0.177,0.094 0.385,0.292 0.208,0.198 10 false *a 1.594,4.365 1.802,4.563 0.208,0.198 10 false *b 3.156,2.208 3.573,2.406 0.417,0.198 10 false CLG7 3.427,0.531 3.865,0.729 0.438,0.198 10 false L196 2.333,4.365 2.542,4.563 0.208,0.198 10 false *c 3.948,2.198 4.365,2.396 0.417,0.198 10 false CG7B 0.99,3.635 1.406,3.833 0.417,0.198 10 false GND 2.375,2.208 2.542,2.406 0.167,0.198 10 false E 2.188,0.542 2.583,0.74 0.396,0.198 10 false L195

Text in Illustration
*1 Waveform - -
*a Component with harness connected
(Certification ECU (smart key ECU assembly))
*b Within approximately 30 seconds from when the door is closed
*c After approximately 30 seconds from when the door is closed - -


b.

Connect the S26 No. 2 indoor electrical key antenna assembly (inside luggage) connector.


c.

Using an oscilloscope, check the waveform.

OK:
Tester Connection Condition Tool Setting Specified Condition
L196-9 (CLG7) - L195-11 (E) Proceed:
1.

Power switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Door is open

4.

Door is closed

5.

Within 30 seconds


2 V/DIV., 500 ms/DIV. Pulse generation (See waveform)
L196-8 (CG7B) - L195-11 (E) Proceed:
1.

Power switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Door is open

4.

Door is closed

5.

Within 30 seconds


2 V/DIV., 500 ms/DIV. Pulse generation (See waveform)




OK

4.REPLACE NO. 2 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (INSIDE LUGGAGE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

4.REPLACE NO. 2 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (INSIDE LUGGAGE)
a.

Temporarily replace the No. 2 indoor electrical key antenna assembly (inside luggage) with a new or known good one (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ELECTRICAL KEY OSCILLATOR(for Rear Floor)>REMOVAL).



NEXT

5.CLEAR DTC
6.CHECK FOR DTC

OK

END (NO. 2 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (INSIDE LUGGAGE) WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)