This DTC is stored when there is a problem in the ACC output circuit. The ACC circuit is the circuit that goes from inside the power management control ECU to the ACC relay.
When the power management control ECU is replaced with a new one and the cable is connected to the negative (-) auxiliary battery terminal, the power source mode changes to on (IG).
When the auxiliary battery cable is disconnected and reconnected, the power source returns to the mode it was in before the auxiliary battery cable was disconnected.
This DTC is stored when a malfunction in the ACC output circuit between the ACC output terminal of the power management control ECU and the ACC relay is detected.
| DTC Code | DTC Detection Condition | Trouble Area | DTC Output Confirmation Operation |
|---|---|---|---|
| B2274 | Malfunction in the ACC relay activation circuit in the power management control ECU or the external circuit (1-trip detection logic*).
|
·
AM2 fuse ·
ACC relay (Instrument panel junction block assembly) ·
Power management control ECU ·
Wire harness or connector |
Wait 10 seconds after turning the power switch on (ACC) or on (IG), and then wait another 10 seconds after turning the power switch off.
|
*: Only output while a malfunction is present and the power switch is on (IG)
| Vehicle Condition when Malfunction Detected | Fail-safe Function when Malfunction Detected |
|---|---|
·
If there is a malfunction when the relay is stuck on, the ACC relay does not turn off even though all the power is off. ·
If there is a malfunction when the relay is off, the ACC relay does not turn on even though the power source mode is on (ACC).
|
- |
When using the GTS with the power switch off, perform either of the following: 1) Turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and vehicle begins, or 2) connect the GTS to the vehicle, select the vehicle type under manual mode, and then enter the following menus:
for Power Source Control: Body Electrical / Power Source Control / Trouble Codes.
for Entry&Start: Body Electrical / Entry&Start / Trouble Codes.
The entry and start system uses multiplex communication. First perform the inspections in "How to Proceed with Troubleshooting" to confirm that there are no communication malfunctions before proceeding with troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING).
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
When the power source mode cannot change to on (ACC), the audio and navigation systems do not operate.
After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.
| DTC | Data List Item | Active Test Item |
|---|---|---|
| B2274 | Power Source Control
ACC Relay Monitor |
- |
OK
NG
OK
NG
Remove the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2A-43 - 2B-4 | 20°C (68°F) | 81.49 to 118.98 Ω |
| 2A-43 - 2B-6 | 20°C (68°F) | 81.49 to 118.98 Ω |
| 2B-4 - 2B-6 | Always | Below 1 Ω |
| *a | Component without harness connected
(Instrument Panel Junction Block Assembly) |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L6-1 (ACCD) - 2A-43 | Always | Below 1 Ω |
| L6-1 (ACCD) - Body ground | Always | 10 kΩ or higher |
OK
NG
Measure the resistance according to the value(s) the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2B-4 - Body ground | Always | Below 1 Ω |
| 2B-6 - Body ground | Always | Below 1 Ω |
OK
NG
Reinstall the instrument panel junction block assembly.
Reconnect the L5 and L6 connectors.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L6-1 (ACCD) - Body ground | Power switch on (ACC) | 9 V or higher |
| *a | Component with harness connected
(Power Management Control ECU) |
OK
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
NG