Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function) › 2012.03–2013.08
RM2070E _58 Vehicle Interior _061938 THEFT DETERRENT / KEYLESS ENTRY _0301768 ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  B2275  STSW Monitor Malfunction  


DESCRIPTION

This DTC is stored when a malfunction is detected in the starter circuit inside the power management control ECU.

HINT:
·

When the power management control ECU is replaced with a new one and the cable is connected to the negative (-) auxiliary battery terminal, the power source mode changes to on (IG).

·

When the auxiliary battery cable is disconnected and reconnected, the power source returns to the mode it was in before the auxiliary battery cable was disconnected.



DTC No. DTC Detection Condition Trouble Area
B2275 Power management control ECU internal HV activation request output circuit malfunction or external circuit malfunction.
·

AM2 fuse

·

Power management control ECU

·

Wire harness or connector



WIRING DIAGRAM

B230178E11
3.779,2.009 5.050,2.314 1.271,0.305 10 Power Management Control ECU 3.999,0.887 4.390,1.026 0.391,0.138 10 AM22 3.999,0.494 4.390,0.632 0.391,0.138 10 AM21 2.474,0.608 2.785,0.747 0.312,0.138 10 AM2 1.11,0.47 1.976,0.776 0.866,0.305 10 from Auxiliary Battery 3.723,0.305 3.819,0.444 0.095,0.138 10 7 3.701,0.887 3.956,1.026 0.255,0.138 10 L5 3.723,0.71 3.819,0.848 0.095,0.138 10 1 4.702,1.28 4.892,1.419 0.189,0.138 10 E1 4.623,1.682 4.891,1.821 0.268,0.138 10 E12 4.626,0.887 4.891,1.026 0.265,0.138 10 E02 4.623,0.494 4.891,0.632 0.268,0.138 10 E01 5.033,0.494 5.282,0.632 0.250,0.138 10 L5 5.062,0.306 5.162,0.444 0.100,0.138 10 5 5.033,0.887 5.282,1.026 0.250,0.138 10 L6 3.701,0.494 3.956,0.632 0.255,0.138 10 L6 5.062,0.705 5.162,0.844 0.100,0.138 10 5 5.033,1.682 5.282,1.821 0.250,0.138 10 L6 5.062,1.497 5.162,1.635 0.100,0.138 10 4 5.033,1.28 5.282,1.419 0.250,0.138 10 L5 5.062,1.099 5.162,1.238 0.100,0.138 10 6

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the power switch off, perform either of the following: 1) Turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and vehicle begins, or 2) connect the GTS to the vehicle, select the vehicle type under manual mode, and then enter the following menus:

for Power Source Control: Body Electrical / Power Source Control / Trouble Codes.

for Entry&Start: Body Electrical / Entry&Start / Trouble Codes.

·

The entry and start system uses multiplex communication. First perform the inspections in "How to Proceed with Troubleshooting" to confirm that there are no communication malfunctions before proceeding with troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (AUXILIARY BATTERY - POWER MANAGEMENT CONTROL ECU)

OK

2.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - BODY GROUND)

OK

3.CHECK FOR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK FOR DTC

b.

Turn the power switch on (IG).


c.

After 25 seconds have elapsed, check if the DTC has been set again.

OK:

DTC B2275 is not output.




OK

NG