Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function) › from 2016.05
RM2070E _58 Vehicle Interior _061938 THEFT DETERRENT / KEYLESS ENTRY _0301768 ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  B2275  STSW Monitor Malfunction  


DESCRIPTION

This DTC is stored when a malfunction is detected in the starter circuit inside the certification ECU (smart key ECU assembly).

HINT:
·

When the certification ECU (smart key ECU assembly) is replaced with a new one and the cable is connected to the negative (-) auxiliary battery terminal, the power source mode changes to on (IG).

·

When the auxiliary battery cable is disconnected and reconnected, the power source returns to the mode it was in before the auxiliary battery cable was disconnected.



DTC No. DTC Detection Condition Trouble Area
B2275 Certification ECU (smart key ECU assembly) internal HV activation request output circuit malfunction or external circuit malfunction.
·

ECU-B2 fuse

·

Certification ECU (smart key ECU assembly)

·

Wire harness or connector



WIRING DIAGRAM

B407099E13
0.635,2.99 2.365,3.427 1.729,0.438 10 false Hybrid Vehicle Control ECU 5.052,3 6.865,3.406 1.813,0.406 10 false Certification ECU (Smart Key ECU Assembly) 5.49,1.646 5.896,1.865 0.406,0.219 10 false ST2 0.625,2.833 1.104,3.104 0.479,0.271 10 false L5 5.063,2.854 5.542,3.125 0.479,0.271 10 false L195 5.479,0.708 5.958,0.979 0.479,0.271 10 false +B 5.49,2.354 5.969,2.625 0.479,0.271 10 false E 1.948,1.531 2.427,1.802 0.479,0.271 10 false 9 1.573,1.656 1.979,1.875 0.406,0.219 10 false ST2 5.281,1.531 5.688,1.75 0.406,0.219 10 false 7 5.24,2.271 5.646,2.49 0.406,0.219 10 false 11 5.281,0.625 5.688,0.844 0.406,0.219 10 false 2 4.333,0.885 5.292,1.167 0.958,0.281 10 false ECU-B2 2.896,0.698 3.74,1.115 0.844,0.417 10 false from Auxiliary Battery

CAUTION / NOTICE / HINT

NOTICE:
·

The entry and start system uses multiplex communication. First perform the inspections in "How to Proceed with Troubleshooting" to confirm that there are no communication malfunctions before proceeding with troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>OPERATION CHECK).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR ((POWER SOURCE)

OK

2.CHECK HARNESS AND CONNECTOR (GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (GROUND)

OK

3.CHECK HARNESS AND CONNECTOR CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - HYBRID VEHICLE CONTROL ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - HYBRID VEHICLE CONTROL ECU)
a.

Disconnect the L195 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the L5 hybrid vehicle control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L195-7 (ST2) - L5-9 (ST2) Always Below 1 Ω
L195-7 (ST2) or L5-9 (ST2) - Body ground Always 10 kΩ or higher




OK

4.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Reconnect the L195 certification ECU (smart key ECU assembly) connector.

U190838E02
2.208,1.729 2.208,2.479 2.208,2.479 2.01,2.479 true 0.302,0.292 0.49,0.448 0.188,0.156 10 false *a 2.156,0.927 2.521,1.146 0.365,0.219 10 false L195 1.74,2.385 2.104,2.542 0.365,0.156 10 false ST2


b.

Reconnect the L5 hybrid vehicle control ECU connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L195-7 (ST2) - Body ground With the brake pedal depressed, the power switch is pressed and held → After approx. 3 sec. has elapsed, the power switch is released 9 V or higher → 1 V or less



Text in Illustration
*a Component with harness connected
(to Certification ECU (Smart Key ECU Assembly))
- -


OK

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)