Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function) › 2012.10–2014.11
RM2070E _58 Vehicle Interior _061938 THEFT DETERRENT / KEYLESS ENTRY _0301768 ENTRY AND START SYSTEM(for Start Function) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  Power Source Mode does not Change to ON (READY)  


DESCRIPTION

When the electronic key is in the cabin and the power switch is pressed, the power management control ECU receives a signal and changes the power source mode. In addition, when the power switch is pressed with park (P) selected and the brake pedal depressed, the hybrid system turns on (READY).

HINT:
·

When the power management control ECU is replaced with a new one and the cable is connected to the negative (-) auxiliary battery terminal, the power source mode changes to on (IG).

·

When the auxiliary battery cable is disconnected and reconnected, the power source returns to the mode it was in before the auxiliary battery cable was disconnected.



WIRING DIAGRAM

B273648E03
0.894,3.107 1.189,3.247 0.295,0.139 10 L43 0.894,3.243 1.756,3.382 0.862,0.139 10 Power Switch 0.772,5.341 1.879,5.478 1.107,0.137 10 Skid Control ECU 0.83,8.397 2.791,8.533 1.962,0.137 10 : CAN Communication Line 0.894,2.809 1.222,2.948 0.327,0.139 10 GND 1.384,2.809 1.772,2.948 0.389,0.139 10 INDW 1.419,2.402 1.772,2.541 0.354,0.139 10 INDS 1.49,2.001 1.773,2.140 0.283,0.139 10 SS2 1.489,1.604 1.773,1.743 0.284,0.139 10 SS1 3.534,2.808 3.923,2.948 0.389,0.139 10 INDW 3.534,2.402 3.888,2.541 0.354,0.139 10 INDS 3.524,4.786 3.935,4.926 0.411,0.139 10 CA1L 3.524,4.388 3.912,4.528 0.388,0.139 10 CA1H 1.409,4.786 1.779,4.926 0.369,0.139 10 CA1L 1.391,4.387 1.779,4.526 0.388,0.139 10 CA1H 3.534,2.001 3.948,2.140 0.414,0.139 10 SSW2 3.534,1.611 3.950,1.750 0.415,0.139 10 SSW1 3.534,1.217 3.948,1.356 0.414,0.139 10 AM22 3.534,0.817 3.950,0.956 0.415,0.139 10 AM21 3.24,1.217 3.492,1.356 0.252,0.139 10 L5 3.24,0.817 3.492,0.956 0.252,0.139 10 L6 3.285,0.627 3.381,0.767 0.095,0.139 10 7 3.275,1.028 3.370,1.167 0.095,0.139 10 1 3.275,1.429 3.370,1.568 0.095,0.139 10 7 3.236,1.822 3.408,1.961 0.172,0.139 10 17 3.275,2.225 3.370,2.364 0.095,0.139 10 8 3.275,2.632 3.370,2.771 0.095,0.139 10 9 1.848,1.513 1.944,1.653 0.095,0.139 10 7 1.848,1.906 1.949,2.045 0.101,0.139 10 2 1.848,2.309 2.031,2.448 0.182,0.139 10 12 1.848,2.716 2.020,2.855 0.172,0.139 10 13 0.709,2.716 0.816,2.855 0.107,0.139 10 5 3.24,2.001 3.492,2.140 0.252,0.139 10 L6 3.24,4.387 3.492,4.526 0.252,0.139 10 L6 3.24,4.786 3.492,4.926 0.252,0.139 10 L6 3.243,4.205 3.416,4.344 0.173,0.139 10 25 3.243,4.609 3.419,4.748 0.176,0.139 10 24 0.772,5.197 1.041,5.337 0.269,0.139 10 A58 1.844,4.643 2.023,4.782 0.179,0.139 10 38 1.844,4.236 2.023,4.376 0.179,0.139 10 37 4.571,4.786 4.823,4.926 0.252,0.139 10 L6 4.571,0.817 4.823,0.956 0.252,0.139 10 L6 4.61,0.631 4.707,0.771 0.097,0.139 10 1 4.524,2.808 4.792,2.948 0.268,0.139 10 A22 4.62,2.617 4.718,2.756 0.098,0.139 10 2 4.571,5.741 4.823,5.880 0.252,0.139 10 L6 3.24,1.611 3.492,1.750 0.252,0.139 10 L5 3.24,2.402 3.492,2.541 0.252,0.139 10 L5 3.24,2.808 3.492,2.948 0.252,0.139 10 L5 4.571,3.594 4.823,3.734 0.252,0.139 10 L5 4.569,3.411 4.747,3.550 0.178,0.139 10 14 5.37,3.85 5.647,3.989 0.276,0.139 10 L27 5.294,3.495 5.469,3.635 0.175,0.139 10 15 4.571,5.337 4.823,5.477 0.252,0.139 10 L5 4.61,5.56 4.705,5.700 0.095,0.139 10 4 4.614,5.157 4.709,5.297 0.095,0.139 10 6 4.571,4.388 4.823,4.528 0.252,0.139 10 L5 4.616,4.61 4.716,4.750 0.100,0.139 10 5 4.612,4.204 4.707,4.344 0.095,0.139 10 5 4.039,0.817 4.451,0.956 0.413,0.139 10 ACCD 4.109,2.808 4.451,2.948 0.342,0.139 10 IG2D 4.067,3.594 4.483,3.734 0.416,0.139 10 SPDI 5.524,3.594 5.724,3.734 0.200,0.139 10 +S 5.852,3.058 6.094,3.198 0.242,0.140 10 IG2 5.673,2.069 6.269,2.207 0.597,0.138 10 P/POINT 5.799,1.052 6.187,1.191 0.388,0.138 10 ACC 5.37,3.997 6.573,4.314 1.203,0.316 10 Combination Meter Sub-assembly 4.186,4.388 4.452,4.528 0.266,0.139 10 E01 4.184,4.786 4.452,4.926 0.268,0.139 10 E02 4.25,5.337 4.439,5.477 0.189,0.139 10 E1 4.17,5.741 4.438,5.880 0.268,0.139 10 E12 3.365,7.865 4.630,8.174 1.264,0.309 10 Power Management Control ECU 1.853,0.938 2.160,1.077 0.307,0.139 10 AM2 0.309,0.793 1.169,1.106 0.860,0.313 10 from Auxiliary Battery

B256307E05
0.521,1.51 0.823,1.677 0.302,0.167 10 false L10 0.521,1.667 2,2.094 1.479,0.427 10 false ID Code Box (Immobiliser Code ECU) 0.552,5.49 2.115,5.854 1.563,0.365 10 false Certification ECU (Smart Key ECU Assembly) 0.531,2.792 0.802,2.938 0.271,0.146 10 false A24 0.531,2.938 2.208,3.313 1.677,0.375 10 false Transmission Control ECU Assembly 3.344,5.927 4.719,6.26 1.375,0.333 10 false Power Management Control ECU 5.198,4.479 5.469,4.635 0.271,0.156 10 false A26 5.198,4.625 6.323,4.823 1.125,0.198 10 false Stop Light Switch 5.406,2.813 6.031,3.042 0.625,0.229 10 false IG1 No. 3 5.406,1.865 6.021,2.052 0.615,0.188 10 false IG1 No. 2 5.417,0.906 6.073,1.094 0.656,0.188 10 false IG1 No. 1 4.094,1.583 4.448,1.76 0.354,0.177 10 false IG1D 4.135,4.208 4.427,4.375 0.292,0.167 10 false STP 3.521,4.219 3.844,4.396 0.323,0.177 10 false LIN2 1.51,4.208 1.76,4.385 0.25,0.177 10 false LIN 1.844,4.063 2.063,4.229 0.219,0.167 10 false 29 0.635,4.906 0.844,5.104 0.208,0.198 10 false 15 0.927,5 1.125,5.177 0.198,0.177 10 false E 0.906,6.26 2.917,6.438 2.01,0.177 10 false : LIN Communication Line 3.51,0.521 3.844,0.677 0.333,0.156 10 false IMO 0.573,5.323 1,5.49 0.427,0.167 10 false L62 0.708,2.427 0.885,2.594 0.177,0.167 10 false 1 1.854,2.406 2.042,2.583 0.188,0.177 10 false 24 4.615,1.396 4.771,1.604 0.156,0.208 10 false 2 3.229,4.208 3.573,4.406 0.344,0.198 10 false L6 4.51,4.208 4.792,4.375 0.281,0.167 10 false A22 4.563,4.021 4.75,4.219 0.188,0.198 10 false 23 5.104,4.115 5.208,4.292 0.104,0.177 10 false 1 6.26,4.115 6.375,4.302 0.115,0.188 10 false 2 3.229,4.01 3.406,4.188 0.177,0.177 10 false 11 3.229,0.354 3.448,0.542 0.219,0.188 10 false 20 1.844,0.448 1.979,0.646 0.135,0.198 10 false 5 1.844,0.802 1.969,0.969 0.125,0.167 10 false 6 1.833,1.104 1.958,1.281 0.125,0.177 10 false 3 0.708,1.146 0.813,1.333 0.104,0.188 10 false 8 3.229,0.708 3.427,0.865 0.198,0.156 10 false 21 3.521,0.875 3.781,1.052 0.26,0.177 10 false IMI 1.479,0.542 1.771,0.729 0.292,0.188 10 false EFII 1.406,0.875 1.771,1.042 0.365,0.167 10 false EFIO 1.448,1.24 1.76,1.438 0.313,0.198 10 false LIN1 0.896,1.24 1.25,1.417 0.354,0.177 10 false GND 1.531,2.531 1.792,2.719 0.26,0.188 10 false LIN 0.896,2.531 1.125,2.729 0.229,0.198 10 false E1 6.438,5.146 6.844,5.323 0.406,0.177 10 false STOP 4.75,4.99 6.094,5.24 1.344,0.25 10 false from Auxiliary Battery 4.563,1.583 4.854,1.76 0.292,0.177 10 false L6 3.219,0.875 3.479,1.052 0.26,0.177 10 false L6 3.229,0.531 3.531,0.74 0.302,0.208 10 false L6

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

When using the GTS with the power switch off, perform either of the following: 1) Turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and vehicle begins, or 2) connect the GTS to the vehicle, select the vehicle type under manual mode, and then enter the following menus:

for Hybrid Control: Powertrain / Hybrid Control / Trouble Codes.

for Power Source Control: Body Electrical / Power Source Control / Trouble Codes.

for Entry&Start: Body Electrical / Entry&Start / Trouble Codes.

·

The entry and start system uses multiplex communication. First perform the inspections in "How to Proceed with Troubleshooting" to confirm that there are no communication malfunctions before proceeding with troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

If the entry and start system is disabled through the customize function, enable the system before performing troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>CUSTOMIZE PARAMETERS).

·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

Before replacing the certification ECU (smart key ECU assembly), ID code box (immobiliser code ECU) or transmission control ECU, refer to the Service Bulletin.

·

After completing repairs, confirm that the problem does not occur.



HINT:
Related Data List and Active Test Items
Problem Symptom Data List Item Active Test Item
Power Source Mode does not Change to ON (READY)
Power Source Control
·

Stop Light Switch1

·

Power Supply Condition

·

IG1 Relay Monitor (Inside)

·

IG2 Relay Monitor (Inside)

·

IG1 Relay Monitor (Outside)

·

IG2 Relay Monitor (Outside)

·

Latch Circuit

·

Starter Request Signal


Entry&Start
·

S Code Check

·

L Code Check

·

Engine Start Request

·

Immobiliser


-


PROCEDURE

1.CHECK HYBRID SYSTEM READY ON
a.

Place the electrical key transmitter sub-assembly (key) on the driver seat.


b.

Depress the brake pedal.


c.

Check that the power switch indicator light is green. Then press the power switch to check if the hybrid system turns on (READY).

OK:

Power source mode becomes on (READY).




OK

END (HYBRID SYSTEM PERMISSION CONDITIONS WERE NOT SATISFIED)

NG

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Turn the power switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG).


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


f.

Enter the following menus: Body Electrical / Power Source Control / Trouble Codes.


g.

Check for DTCs.

Result:
Result Proceed to
DTC is not output A
Hybrid control system DTC is output B
Entry and start system (for start function) DTC is output C




A

3.CHECK POWER SOURCE CONDITION

B

GO TO HYBRID CONTROL SYSTEM (DIAGNOSTIC TROUBLE CODE CHART)

C

3.CHECK POWER SOURCE CONDITION
a.

Check the power source mode change.

i.

When the key is inside the vehicle and the park (P) is selected, check that pressing the power switch causes the power source mode to change.

Result:
Result Proceed to
off → on (ACC) → on (IG) → off A
Power source mode does not change to on (IG and ACC) B
Power source mode does not change to on (IG) C
Power source mode does not change to on (ACC) D





A

4.READ VALUE USING GTS (STOP LIGHT SWITCH ASSEMBLY)

B

C

D

4.READ VALUE USING GTS (STOP LIGHT SWITCH ASSEMBLY)
a.

Read the Data List according to the display on the GTS.

Power Source Control
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Stop Light Switch1 State of brake pedal/OFF or ON OFF: Brake pedal released
ON: Brake pedal depressed
·

Use this item to determine whether the stop light switch is malfunctioning.

·

The hybrid control system cannot be started when this item is "OFF".

·

When this item is malfunctioning, the hybrid control system can be started by pressing and holding the power switch for a certain period of time.



OK:

ON (brake pedal is depressed) and OFF (brake pedal is released) appear on the screen.




OK

5.READ VALUE USING GTS (L CODE)

NG

10.INSPECT STOP LIGHT SWITCH ASSEMBLY
5.READ VALUE USING GTS (L CODE)
a.

Enter the following menus: Body Electrical / Entry&Start / Data List.


b.

Read the Data List according to the display on the GTS.

Entry&Start
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
L Code Check Verification result between ID code box and transmission control ECU assembly/OK or NG OK: Verification result normal
NG: Verification result abnormal
When a malfunction is present:
·

The ID code for the ID code box or transmission control ECU assembly is not registered or the ID code box or transmission control ECU assembly is malfunctioning.

·

The gearshift control cannot be locked.

·

The gearshift control cannot be unlocked (the hybrid control system cannot be started).



OK:

OK appears on the screen.




OK

6.READ VALUE USING GTS (ENGINE START REQUEST)

NG

12.REPLACE TRANSMISSION CONTROL ECU ASSEMBLY
6.READ VALUE USING GTS (ENGINE START REQUEST)
a.

Read the Data List according to the display on the GTS.

Entry&Start
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Engine Start Request Reception state of hybrid control system start permission signal determined by ID code box and sent to certification ECU (smart key ECU assembly)/OK or NG OK: Receiving signal
NG: Not receiving signal
·

When this item displays "OK", the certification ECU (smart key ECU assembly) has received hybrid system start request signal from the ID code box and has permitted hybrid control system start.

·

The hybrid control system cannot be started when this item displays "NG".



OK:

OK appears on the screen.




OK

7.READ VALUE USING GTS (S CODE)

NG

12.REPLACE TRANSMISSION CONTROL ECU ASSEMBLY
7.READ VALUE USING GTS (S CODE)
a.

Read the Data List according to the display on the GTS.

Entry&Start
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
S Code Check Verification result between certification ECU (smart key ECU assembly) and ID code box/OK or NG OK: Verification result normal
NG: Verification result abnormal
When a malfunction is present:
·

The ID code for the certification ECU (smart key ECU assembly) or ID code box is not registered or the certification ECU (smart key ECU assembly) or ID code box is malfunctioning.

·

The gearshift control cannot be locked.

·

The gearshift control cannot be unlocked (the hybrid control system cannot be started).



OK:

OK appears on the screen.




OK

8.CHECK ID CODE BOX (IMMOBILISER CODE ECU)

NG

14.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
8.CHECK ID CODE BOX (IMMOBILISER CODE ECU)
a.
U154554E03
1.802,1.031 1.51,1.802 false 2.667,1.177 2.396,1.802 false 2.719,1.177 2.99,1.813 false 2.531,0.302 2.813,0.479 0.281,0.177 10 false L6 1.979,0.302 2.354,0.542 0.375,0.24 10 false L5 0.083,0.042 0.281,0.219 0.198,0.177 10 false *a 2.854,1.802 3.156,1.979 0.302,0.177 10 false IMO 2.292,1.802 2.542,2.042 0.25,0.24 10 false IMI 1.406,1.802 1.677,2.021 0.271,0.219 10 false E1

Measure the voltage according to the value(s) in the table below.

Text in Illustration
*a Component with harness connected
(Power Management Control ECU)

i.

Waveform 1

B253467E01
2.177,1.292 2.365,1.468 0.188,0.176 10 *a 2.779,1.296 2.967,1.472 0.188,0.176 10 *b 1.554,1.171 1.884,1.346 0.331,0.176 10 GND

Text in Illustration
*a Approximately 160 ms *b Approximately 510 ms

Measurement Condition
Item Content
Tester Connection L6-20 (IMO) - L5-6 (E1)
Tool Setting 2 V/DIV., 200 ms./DIV.
Condition Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after auxiliary battery cable disconnected and reconnected


ii.

Waveform 2

B253466E01
3.499,1.324 3.687,1.500 0.188,0.176 10 *a 4.102,1.328 4.290,1.504 0.188,0.176 10 *b 1.554,1.171 1.884,1.346 0.331,0.176 10 GND

Text in Illustration
*a Approximately 160 ms *b Approximately 510 ms

Measurement Condition
Item Content
Tester Connection L6-21 (IMI) - L5-6 (E1)
Tool Setting 2 V/DIV., 200 ms./DIV.
Condition Power switch on (IG)

OK:

The waveform is displayed as shown in illustration.





OK

9.READ VALUE USING GTS

NG

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

9.READ VALUE USING GTS
a.

Enter the following menus: Body Electrical / Power Source Control / Data List.


b.

Read the Data List according to the display on the GTS.

Power Source Control
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Starter Request Signal Condition of hybrid control system start command signal/OFF or ON OFF: Power switch released after approximately 1 second elapses
ON: Power switch pressed and held while carrying key with park (P) selected and brake pedal depressed
·

This item displays "ON" when starting the hybrid control system.

·

The hybrid control system cannot be started when this item is "OFF".



OK:

Data List display changes when the power switch is operated.




OK

NG

10.INSPECT STOP LIGHT SWITCH ASSEMBLY

OK

11.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - STOP LIGHT SWITCH ASSEMBLY)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

11.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - STOP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the A22 connector from the power management control ECU.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A22-23 (STP) - A26-1 Always Below 1 Ω
A22-23 (STP) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.REPLACE TRANSMISSION CONTROL ECU ASSEMBLY
a.

Replace transmission control ECU assembly (See page Drivetrain>P410 (HYBRID TRANSMISSION / TRANSAXLE)>SHIFT LEVER>REMOVAL).



NEXT

13.CHECK HYBRID SYSTEM READY ON
13.CHECK HYBRID SYSTEM READY ON
a.

Place the electrical key transmitter sub-assembly (key) on the driver seat.


b.

Depress the brake pedal.


c.

Check that the power switch indicator light is green. Then press the power switch to check if the hybrid system turns on (READY).

OK:

Power source mode becomes on (READY).




OK

END (TRANSMISSION CONTROL ECU ASSEMBLY WAS DEFECTIVE)

NG

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

14.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Replace the certification ECU (smart key ECU assembly).

HINT:

Refer to the Service Bulletin.




NEXT

15.CHECK HYBRID SYSTEM READY ON
15.CHECK HYBRID SYSTEM READY ON
a.

Place the electrical key transmitter sub-assembly (key) on the driver seat.


b.

Depress the brake pedal.


c.

Check that the power switch indicator light is green. Then press the power switch to check if the hybrid system turns on (READY).

OK:

Power source mode becomes on (READY).




OK

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)

NG

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)