Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM › from 2016.05
RM2070E _58 Vehicle Interior _061938 THEFT DETERRENT / KEYLESS ENTRY _0301769 ENGINE IMMOBILISER SYSTEM C

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM  B2799  Engine Immobiliser System Malfunction  


DESCRIPTION

When there are communication malfunctions between the hybrid vehicle control ECU and ID code box (immobiliser code ECU), or when the communication ID codes do not match, the hybrid vehicle control ECU stores this DTC.

DTC Code DTC Detection Condition Trouble Area DTC Output Confirmation Operation
B2799 Either condition is met (1 trip detection logic*):
·

A malfunction in the communication or communication lines between the hybrid vehicle control ECU and ID code box (immobiliser code ECU).

·

A matching communication code cannot be verified during communication between the hybrid vehicle control ECU and ID code box (immobiliser code ECU).


·

ID code box (immobiliser code ECU)

·

Hybrid vehicle control ECU

·

Wire harness or connector


Either condition is met:
·

10 seconds after a hybrid control system start operation (with the shift lever in P and the brake pedal depressed, the power switch is pressed while carrying the key). If there is a malfunction, the hybrid control system does not start (communication begins within 3 seconds of the hybrid control system start operation, and DTCs are stored after 6 seconds).

·

10 seconds after the power switch is turned on (IG) after reconnecting the cable to the negative (-) auxiliary battery terminal (communication begins within 3 seconds of the power switch being turned on (IG), and DTCs are stored after 6 seconds).



*: Only output while a malfunction is present.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Hybrid control system cannot be started -

Related Data List and Active Test
DTC Code Data List and Active Test
B2799 -

WIRING DIAGRAM

B255097E48
0.292,1.823 1.75,2.052 1.458,0.229 10 false L6 0.292,1.979 2.49,2.26 2.198,0.281 10 false Hybrid Vehicle Control ECU 5.396,1.969 5.823,2.208 0.427,0.24 10 false L191 5.396,2.125 7.01,2.448 1.615,0.323 10 false ID Code Box (Immobiliser Code ECU) 1.25,1.24 1.573,1.531 0.323,0.292 10 false IMO 1.313,0.5 1.688,0.76 0.375,0.26 10 false IMI 5.708,0.5 6.26,0.906 0.552,0.406 10 false EFIO 5.708,1.25 6.188,1.5 0.479,0.25 10 false EFII 5.521,1.135 5.823,1.438 0.302,0.302 10 false 3 5.521,0.375 5.823,0.688 0.302,0.313 10 false 4 1.604,1.135 2.781,1.458 1.177,0.323 10 false 23 1.594,0.385 3.396,0.75 1.802,0.365 10 false 22

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the ID code box (immobiliser code ECU) or hybrid vehicle control ECU, refer to Service Bulletin.

·

After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.



HINT:

When DTC B2799 and the certification ECU (smart key ECU assembly) DTC are output simultaneously, first perform troubleshooting for the certification ECU (smart key ECU assembly) DTC.


PROCEDURE

1.REGISTER ECU COMMUNICATION ID
a.

Reregister the ECU communication ID.

HINT:

Refer to Service Bulletin.




NEXT

2.CHECK HYBRID VEHICLE CONTROL ECU ASSEMBLY (TERMINAL IMO)
2.CHECK HYBRID VEHICLE CONTROL ECU ASSEMBLY (TERMINAL IMO)
a.

Using an oscilloscope, check the waveform.

U190937E02
5.302,1.375 5.302,2.281 5.302,2.281 5.656,2.281 true 3.104,3.927 3.104,4.51 3.104,4.51 3.292,4.51 false 2.917,3.938 2.917,4.521 2.917,4.521 2.729,4.521 false 5.26,0.323 5.656,0.625 0.396,0.302 10 false L6 0.208,0.135 0.604,0.438 0.396,0.302 10 false *a 2.948,2.958 3.344,3.26 0.396,0.302 10 false *b 2.573,4.417 2.969,4.719 0.396,0.302 10 false *c 0.948,3.885 1.344,4.188 0.396,0.302 10 false GND 3.313,4.417 3.708,4.719 0.396,0.302 10 false *d 5.719,2.208 6.115,2.51 0.396,0.302 10 false IMO

Text in Illustration
*a Component with harness connected
(Hybrid Vehicle Control ECU)
*b Waveform
*c Approximately 160 ms. *d Approximately 270 ms.

Measurement Condition:
Tester Connection Condition Tool Setting Specified Condition
L6-23 (IMO) - Body ground Turn the power switch on (READY) 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform)



Result:
Result Proceed to
Normal waveform A
Terminal IMO stuck low (2.4 V or less) B
Waveform not output, or has abnormal wavelength or shape C



A

3.CHECK HYBRID VEHICLE CONTROL ECU ASSEMBLY (TERMINAL IMI)

B

6.CHECK ID CODE BOX (IMMOBILISER CODE ECU)

C

3.CHECK HYBRID VEHICLE CONTROL ECU ASSEMBLY (TERMINAL IMI)
a.

Using an oscilloscope, check the waveform.

U190938E02
5.396,1.344 5.396,2.323 5.396,2.323 5.542,2.323 true 3.49,4.042 3.49,4.594 3.49,4.594 3.625,4.594 false 3.313,4.052 3.313,4.604 3.313,4.604 3.167,4.604 false 0.135,0.094 0.5,0.458 0.365,0.365 10 false *a 3.323,2.979 3.688,3.344 0.365,0.365 10 false *b 2.99,4.5 3.271,4.729 0.281,0.229 10 false *c 3.646,4.49 3.927,4.719 0.281,0.229 10 false *d 5.26,0.313 5.625,0.469 0.365,0.156 10 false L6 5.594,2.24 5.969,2.438 0.375,0.198 10 false IMI 0.938,3.99 1.448,4.302 0.51,0.313 10 false GND

Text in Illustration
*a Component with harness connected
(Hybrid Vehicle Control ECU)
*b Waveform
*c Approximately 160 ms. *d Approximately 270 ms.

Measurement Condition:
Tester Connection Condition Tool Setting Specified Condition
L6-22 (IMi) - Body ground Power switch turned on (IG) using registered electrical key transmitter sub-assembly 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform)




OK

4.REGISTER ECU COMMUNICATION ID

NG

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

4.REGISTER ECU COMMUNICATION ID
a.

Reregister the ECU communication ID.

HINT:

Refer to Service Bulletin.




NEXT

5.CHECK WHETHER HYBRID CONTROL SYSTEM STARTS
5.CHECK WHETHER HYBRID CONTROL SYSTEM STARTS
a.

Check that the hybrid control system starts with an already registered vehicle key.

OK:

Hybrid control system starts normally.




OK

END (ECU COMMUNICATION ID HAS NOT BEEN REGISTERED)

NG

6.CHECK ID CODE BOX (IMMOBILISER CODE ECU)
a.

Disconnect the L6 hybrid vehicle control ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L6-23 (IMO) - Body ground Power switch turned on (IG) using registered electrical key transmitter sub-assembly Terminal IMO stuck low (2.4 V or less)



Result:
Result Proceed to
Terminal IMO stuck low (2.4 V or less) A
Terminal IMO stuck high (12 V) or abnormal waveform B



A

7.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - HYBRID VEHICLE CONTROL ECU ASSEMBLY)

B

7.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - HYBRID VEHICLE CONTROL ECU ASSEMBLY)
a.

Disconnect the L191 ID code box (immobiliser code ECU) connector.


b.

Disconnect the L6 hybrid vehicle control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L191-3 (EFII) - L6-23 (IMO) Always Below 1 Ω
L191-3 (EFII) or L6-23 (IMO) - Body ground Always 10 kΩ or higher
L191-4 (EFIO) - L6-22 (IMI) Always Below 1 Ω
L191-4 (EFIO) or L6-22 (IMI) - Body ground Always 10 kΩ or higher




OK

8.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)
a.

Replace the ID code box (immobiliser code ECU).

HINT:

Refer to Service Bulletin.




NEXT

9.REGISTER RECOGNITION CODE
9.REGISTER RECOGNITION CODE
a.

Register the recognition codes in the ECUs.

HINT:

Refer to Service Bulletin.




NEXT

10.REGISTER ECU COMMUNICATION ID
10.REGISTER ECU COMMUNICATION ID
a.

Reregister the ECU communication ID.

HINT:

Refer to Service Bulletin.




NEXT

11.CHECK WHETHER HYBRID CONTROL SYSTEM STARTS
11.CHECK WHETHER HYBRID CONTROL SYSTEM STARTS
a.

Check that the hybrid control system starts with an already registered vehicle key.

OK:

Hybrid control system starts normally.




A

END (ID CODE BOX (IMMOBILISER CODE ECU) WAS DEFECTIVE)

B