Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM › 2012.03–2016.05
RM2070E _58 Vehicle Interior _061938 THEFT DETERRENT / KEYLESS ENTRY _0301769 ENGINE IMMOBILISER SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM  Security Indicator Light Does not Blink  


DESCRIPTION

·

The certification ECU (smart key ECU assembly) blinks the security indicator light when the immobiliser is set (power switch off, or driver door is opened and closed with power switch on (IG)).

·

w/ Theft Deterrent System:

The certification ECU (smart key ECU assembly) receive the security indicator light signal from the main body ECU (multiplex network body ECU) via CAN communication when the theft deterrent system is arming preparation state or alarm sounding state. Then, certification ECU (smart key ECU assembly) blinks the security indicator light.


WIRING DIAGRAM

B318529E04
0.161,0.873 0.413,1.026 0.251,0.152 10 L27 0.161,1.041 2.276,1.379 2.115,0.338 10 Combination Meter Sub-assembly (Meter Circuit Plate) 3.077,1.041 5.914,1.203 2.837,0.162 10 Certification ECU (Smart Key ECU Assembly) 1.779,0.393 1.875,0.546 0.095,0.152 10 5 1.508,0.481 1.699,0.633 0.191,0.152 10 LP 3.839,0.393 3.934,0.546 0.095,0.152 10 2 3.296,1.673 3.391,1.825 0.095,0.152 10 * 0.291,3.387 2.055,3.539 1.764,0.152 10 *: w/ Theft Deterrent System 4.016,0.481 4.274,0.633 0.258,0.152 10 IND 4.745,1.652 4.918,1.804 0.173,0.152 10 23 3.761,1.652 3.933,1.804 0.173,0.152 10 51 5,1.767 5.258,1.920 0.258,0.152 10 IND 4.776,2.132 5.003,2.284 0.227,0.152 10 MB 4.776,2.272 6.420,2.591 1.644,0.319 10 Main Body ECU (Multiplex Network Body ECU 3.077,0.873 3.336,1.026 0.258,0.152 10 L62 3.879,3.224 6.523,3.385 2.644,0.162 10 Instrument Panel Junction Block Assembly 3.879,3.055 4.068,3.208 0.189,0.152 10 2A 4.024,1.646 4.282,1.798 0.258,0.152 10 IND

CAUTION / NOTICE / HINT

NOTICE:

Before replacing the certification ECU (smart key ECU assembly), ID code box (immobiliser code ECU) or transmission control ECU, refer to the Service Bulletin.


PROCEDURE

1.SYSTEM CHECK
a.

Check the vehicle specification.

Result:
Result Proceed to
w/ Theft Deterrent System A
w/o Theft Deterrent System B




A

2.PERFORM ACTIVE TEST USING GTS (SECURITY INDICATOR LIGHT)

B

10.PERFORM ACTIVE TEST USING GTS
2.PERFORM ACTIVE TEST USING GTS (SECURITY INDICATOR LIGHT)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Entry&Start or Main Body / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Entry&Start
Tester Display Test Part Control Range Diagnostic Note
Immobiliser Indicator Security indicator light OFF/ON The test is possible when the following conditions are met:
·

The key is in the cabin.

·

The power switch is on (IG).



Main Body (Main Body ECU (Multiplex Network Body ECU))
Tester Display Test Part Control Range Diagnostic Note
Security Indicator Security indicator light OFF/ON -

Result:
Result Proceed to
Security indicator light operation is normal when performing the "Main Body" and "Entry&Start" Active Test A
·

Security indicator light operation is not normal when performing the "Entry&Start" Active Test

·

Security indicator light operation is normal when performing the "Main Body" Active Test


B
·

Security indicator light operation is normal when performing the "Entry&Start" Active Test

·

Security indicator light operation is not normal when performing the "Main Body" Active Test


C
Security indicator light operation is not normal when performing the "Main Body" and "Entry&Start" Active Test D




A

3.CHECK SECURITY INDICATOR LIGHT OPERATION

B

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER SUB-ASSEMBLY - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))

C

5.CHECK HARNESS AND CONNECTOR (COMBINATION METER SUB-ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

D

7.CHECK HARNESS AND CONNECTOR
3.CHECK SECURITY INDICATOR LIGHT OPERATION
a.

When the immobiliser is set, check that the security indicator light blinks.*1

OK:

The security indicator light blinks normally.



b.

When the theft deterrent system is in the arming preparation state, check that the security indicator light on.*2

OK:

The security indicator light is on normally.


Result:
Result Proceed to
Both *1 and *2 are OK A
*1 is NG (*2 is OK) B
*2 is NG (*1 is OK) C
Both *1 and *2 are NG D




A

USE SIMULATION METHOD TO CHECK

B

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

C

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

D

REPLACE COMBINATION METER SUB-ASSEMBLY (METER CIRCUIT PLATE)

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER SUB-ASSEMBLY - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Disconnect the combination meter sub-assembly (meter circuit plate) connector.


b.

Disconnect the certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L62-2 (IND) - L27-5 (LP) Always Below 1 Ω
L62-2 (IND) - Body ground Always 10 kΩ or higher




OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (COMBINATION METER SUB-ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the combination meter sub-assembly (meter circuit plate) connector.


b.

Disconnect the instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2A-51 (IND) - L27-5 (LP) Always Below 1 Ω
2A-51 (IND) - Body ground Always 10 kΩ or higher




OK

6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).

U190813E02
5.177,1.792 5.031,2.208 false 2.813,1.719 2.635,2.208 false 0.24,0.156 0.448,0.323 0.208,0.167 10 false *a 4.854,0.156 5.063,0.323 0.208,0.167 10 false *b 1.917,1.177 2.156,1.323 0.24,0.146 10 false MB 5.594,0.917 5.792,1.063 0.198,0.146 10 false 2A 4.896,2.208 5.156,2.385 0.26,0.177 10 false IND 2.51,2.208 2.771,2.385 0.26,0.177 10 false IND


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

HINT:

This inspection is to check the LIN line in the instrument panel junction block assembly that connects the wire harness to the built-in main body ECU (multiplex network body ECU).


Standard Resistance:
Tester Connection Condition Specified Condition
2A-51 (IND) - MB-23 (IND) Always Below 1 Ω


Text in Illustration
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
*b Component without harness connected
(Instrument Panel Junction Block Assembly)



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

7.CHECK HARNESS AND CONNECTOR
a.

Disconnect combination meter sub-assembly (meter circuit plate) connector.


b.

Disconnect the certification ECU (smart key ECU assembly) connector.


c.

Disconnect the instrument panel junction block assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L62-2 (IND) - L27-5 (LP) Always Below 1 Ω
2A-51 (IND) - L27-5 (LP) Always Below 1 Ω
L27-5 (LP) - Body ground Always 10 kΩ or higher




OK

8.REPLACE COMBINATION METER SUB-ASSEMBLY (METER CIRCUIT PLATE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.REPLACE COMBINATION METER SUB-ASSEMBLY (METER CIRCUIT PLATE)
a.

Temporarily replace the combination meter sub-assembly (meter circuit plate) with a new or known good one (See page Vehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL).


b.

When the immobiliser is set or theft deterrent system is in the arming preparation state, check that the security indicator light blinks.

OK:

Security indicator light blinks.




OK

END (COMBINATION METER SUB-ASSEMBLY (METER CIRCUIT PLATE) WAS DEFECTIVE)

NG

9.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
9.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Temporarily replace the certification ECU (smart key ECU assembly) with a new or known good one.

HINT:

Refer to Service Bulletin.



b.

When the immobiliser is set or theft deterrent system is in the arming preparation state, check that the security indicator light blinks.

OK:

Security indicator light blinks.




OK

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

10.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Entry&Start / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Entry&Start
Tester Display Test Part Control Range Diagnostic Note
Immobiliser Indicator Security indicator light OFF/ON The test is possible when the following conditions are met:
·

The key is in the cabin.

·

The power switch is on (IG).



OK:

The security indicator light operates normally by using the Active Test.




OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

11.CHECK HARNESS AND CONNECTOR (COMBINATION METER SUB-ASSEMBLY (METER CIRCUIT PLATE) - CERTIFICATION ECU)
11.CHECK HARNESS AND CONNECTOR (COMBINATION METER SUB-ASSEMBLY (METER CIRCUIT PLATE) - CERTIFICATION ECU)
a.

Disconnect the combination meter sub-assembly (meter circuit plate) connector.


b.

Disconnect the certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L62-2 (IND) - L27-5 (LP) Always Below 1 Ω
L62-2 (IND) - Body ground Always 10 kΩ or higher




OK

12.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Temporarily replace the certification ECU (smart key ECU assembly) with a new or known good one.

HINT:

Refer to Service Bulletin.



b.

When the immobiliser is set or theft deterrent system is in the arming preparation state, check that the security indicator light blinks.

OK:

Security indicator light blinks.




OK

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)

NG

REPLACE COMBINATION METER SUB-ASSEMBLY (METER CIRCUIT PLATE)