Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM › from 2016.05
RM2070E _58 Vehicle Interior _061938 THEFT DETERRENT / KEYLESS ENTRY _0301769 ENGINE IMMOBILISER SYSTEM C

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM  B279A  Theft Deterrent System Communication Line High Fixation  


DESCRIPTION

When the communication line (IMI - EFIO) between the hybrid vehicle control ECU and ID code box (immobiliser code ECU) is stuck high, the hybrid vehicle control ECU stores this DTC.

DTC Code DTC Detection Condition Trouble Area DTC Output Confirmation Operation
B279A The communication line (IMI - EFIO) between the hybrid vehicle control ECU and ID code box (immobiliser code ECU) is stuck high (1 trip detection logic*).
·

Wire harness or connector (disconnection or break in wire harness is main cause)

·

ID code box (immobiliser code ECU)

·

Hybrid vehicle control ECU


Turn the power switch on (IG) and wait 6 seconds.

*: Only output while a malfunction is present.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Hybrid control system cannot be started Hybrid control system cannot be started

Related Data List and Active Test
DTC Code Data List and Active Test
B279A -

WIRING DIAGRAM

B288680E18
5.177,0.979 5.635,1.292 0.458,0.313 10 false EFIO 1.823,0.979 2.083,1.156 0.26,0.177 10 false IMI 0.979,1.813 1.281,1.958 0.302,0.146 10 false L6 4.938,1.875 5.396,2.156 0.458,0.281 10 false L191 0.979,1.979 2.833,2.25 1.854,0.271 10 false Hybrid Vehicle Control ECU 4.938,2.031 6.635,2.406 1.698,0.375 10 false ID Code Box (Immobiliser Code ECU) 4.969,0.917 5.156,1.063 0.188,0.146 10 false 4 2.146,0.938 2.323,1.083 0.177,0.146 10 false 22

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the ID code box (immobiliser code ECU) or hybrid vehicle control ECU, refer to Service Bulletin.

·

After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.



HINT:

When DTC B279A and the certification ECU (smart key ECU assembly) DTC are output simultaneously, first perform troubleshooting for the certification ECU (smart key ECU assembly) DTC.


PROCEDURE

1.CLEAR DTC

NEXT

2.CHECK DTC OUTPUT
2.CHECK DTC OUTPUT
a.

Turn the power switch on (IG) and wait 10 seconds.


b.

Check for DTCs (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC B279A is output A
DTC B279A and other DTCs are output B


HINT:

If DTCs other than DTC B279A are output, troubleshoot those DTCs first.




A

3.CHECK CONNECTION OF CONNECTOR

B

3.CHECK CONNECTION OF CONNECTOR
a.

Turn the power switch off.


b.

Check that the connectors are properly connected to the hybrid vehicle control ECU and ID code box (immobiliser code ECU).

OK:

Connectors are properly connected.




OK

4.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - HYBRID VEHICLE CONTROL ECU)

NG

CONNECT CONNECTORS PROPERLY

4.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - HYBRID VEHICLE CONTROL ECU)
a.

Disconnect the L191 ID code box (immobiliser code ECU) connector.


b.

Disconnect the L6 hybrid vehicle control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L191-4 (EFIO) - L6-22 (IMI) Always Below 1 Ω
L191-4 (EFIO) or L6-22 (IMI) - Body ground Always 10 kΩ or higher




OK

5.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)
a.

Replace the ID code box (immobiliser code ECU) with a new one.

HINT:

Refer to Service Bulletin.




NEXT

6.REGISTER RECOGNITION CODES
6.REGISTER RECOGNITION CODES
a.

Register the recognition codes in the ECUs.

HINT:

Refer to Service Bulletin.




NEXT

7.REGISTER ECU COMMUNICATION ID
7.REGISTER ECU COMMUNICATION ID
a.

Register the ECU communication ID.

HINT:

Refer to Service Bulletin.




NEXT

8.CHECK WHETHER HYBRID CONTROL SYSTEM STARTS
8.CHECK WHETHER HYBRID CONTROL SYSTEM STARTS
a.

Check that the hybrid control system starts with an already registered vehicle key.

OK:

Hybrid control system starts normally.




A

END (ID CODE BOX (IMMOBILISER CODE ECU) WAS DEFECTIVE)

B