Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM
RM2070E _58 Vehicle Interior _061938 THEFT DETERRENT / KEYLESS ENTRY _0301770 THEFT DETERRENT SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  Engine Hood Courtesy Switch Circuit  


DESCRIPTION

The engine hood courtesy switch is installed together with the hood lock. This switch turns on when the engine hood is closed and turns off when the engine hood is opened.

WIRING DIAGRAM

B289668E21
5.103,2.689 6.290,3.173 1.186,0.484 10 Main Body ECU (Multiplex Network Body ECU) 4.006,1.717 5.073,2.211 1.067,0.493 10 Instrument Panel Junction Block Assembly 5.103,2.545 5.329,2.683 0.226,0.138 10 MB 5.212,1.009 5.617,1.147 0.405,0.138 10 HCTY 1.813,1.405 3.676,1.715 1.862,0.310 10 Engine Hood Courtesy Switch (Hood Lock Assembly) 1.813,1.265 2.104,1.401 0.291,0.136 10 A47 2.269,0.899 2.367,1.047 0.098,0.148 10 2 4.94,0.899 5.123,1.047 0.183,0.148 10 20 4.18,0.793 4.363,0.931 0.183,0.138 10 38 4.178,0.998 4.373,1.135 0.195,0.137 10 2C 3.111,0.899 3.208,1.047 0.098,0.148 10 1

PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

According to the display on the GTS, read the Data List.

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Hood Courtesy SW Engine hood courtesy switch/ON or OFF ON: Engine hood open
OFF: Engine hood close
-

OK:

The indicator on the GTS switches between ON and OFF in accordance with the engine hood courtesy switch (hood lock assembly) status.




OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

2.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
2.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the main body ECU (multiplex network body ECU) (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).

U190816E02
0.15,0.133 0.298,0.271 0.149,0.137 10 *a 1.177,0.562 1.372,0.699 0.195,0.137 10 2C 4.811,0.568 5.037,0.704 0.226,0.137 10 MB 5.545,1.445 5.941,1.582 0.395,0.137 10 HCTY 5.363,1.265 5.363,1.51 5.363,1.51 5.517,1.51 false


Text in Illustration
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -

b.

Disconnect the 2C instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2C-38 - MB-20 (HCTY) Always Below 1 Ω




OK

3.INSPECT ENGINE HOOD COURTESY SWITCH (HOOD LOCK ASSEMBLY)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

3.INSPECT ENGINE HOOD COURTESY SWITCH (HOOD LOCK ASSEMBLY)
a.
B277688E01
0.18,0.18 0.329,0.325 0.149,0.145 10 *a 1.555,0.128 1.704,0.274 0.149,0.145 10 *1 1.52,0.216 1.325,0.216 1.325,0.216 1.325,0.632 false 1.984,0.3 2.133,0.446 0.149,0.145 10 *2 1.95,0.387 1.755,0.387 1.755,0.387 1.755,0.882 false

Remove the hood lock assembly (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE HOOD COURTESY SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 Opened 10 kΩ or higher
1 - 2 Locked Below 1 Ω


Text in Illustration
*1 Opened
*2 Locked
*a Component without harness connected
(Engine Hood Courtesy Switch (Hood Lock Assembly))



OK

4.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - ENGINE HOOD COURTESY SWITCH - BODY GROUND)

NG

REPLACE ENGINE HOOD COURTESY SWITCH (HOOD LOCK ASSEMBLY)

4.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - ENGINE HOOD COURTESY SWITCH - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A47-1 - 2C-38 Always Below 1 Ω
A47-1 - Body ground Always 10 kΩ or higher
A47-2 - Body ground Always Below 1 Ω




OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR