Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM
RM2070E _58 Vehicle Interior _061938 THEFT DETERRENT / KEYLESS ENTRY _0301770 THEFT DETERRENT SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  Security Horn Circuit  


DESCRIPTION

When the theft deterrent system is switched from the armed state to the alarm sounding state, the main body ECU (multiplex network body ECU) transmits a signal to cause the security horn to sound at intervals of 0.4 seconds.

WIRING DIAGRAM

B289670E29
2.311,0.978 2.405,1.115 0.094,0.136 10 1 2.311,1.633 2.405,1.770 0.094,0.136 10 5 3.241,0.978 3.335,1.115 0.094,0.136 10 2 3.241,1.633 3.335,1.770 0.094,0.136 10 3 5.591,0.977 5.764,1.114 0.173,0.137 10 17 4.85,0.87 5.022,1.006 0.172,0.136 10 39 1.19,1.238 1.755,1.376 0.565,0.138 10 S-HORN 2.556,2.093 3.121,2.231 0.565,0.138 10 S-HORN 5.874,1.091 6.085,1.228 0.211,0.137 10 SH 4.85,1.091 5.046,1.227 0.195,0.137 10 2C 5.39,3.471 7.031,3.774 1.640,0.303 10 Main Body ECU (Multiplex Network Body ECU) 1.429,2.581 3.331,2.886 1.902,0.305 10 Engine Room Relay Block and Junction Block Assembly 4.692,1.68 5.760,2.149 1.069,0.470 10 Instrument Panel Junction Block Assembly 4.111,4.162 4.205,4.298 0.095,0.136 10 1 4.475,4.242 4.754,4.380 0.280,0.138 10 A70 4.475,4.385 5.333,4.688 0.859,0.303 10 Security Horn Assembly 0.884,3.863 2.237,4.000 1.353,0.136 10 from Auxiliary Battery 5.39,3.316 5.617,3.452 0.227,0.137 10 MB

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Active Test.


e.

According to the display on the GTS, perform the Active Test.

Main Body
Tester Display Test Part Control Range Diagnostic Note
Security Horn Security horn ON / OFF -


OK:

The security horn assembly sounds and stops correctly when operated through the GTS.



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

2.INSPECT SECURITY HORN ASSEMBLY
2.INSPECT SECURITY HORN ASSEMBLY

b.

Check the operation of the security horn assembly.

Standard:
Measurement Condition Specified Condition
Auxiliary battery positive (+) → Terminal 1 Horn sounds
Auxiliary battery negative (-) → Horn body




OK

3.INSPECT S-HORN RELAY

NG

3.INSPECT S-HORN RELAY
a.
B273671E04
2.865,0.711 2.965,0.850 0.100,0.139 10 3 2.285,0.842 2.380,0.980 0.095,0.139 10 5 0.116,0.093 0.274,0.231 0.158,0.139 10 *a 2.52,1.215 2.615,1.354 0.095,0.139 10 2 2.628,1.548 2.723,1.686 0.095,0.139 10 1 2.372,1.304 2.507,1.304 false 2.738,1.633 2.873,1.633 false 2.479,1.067 2.479,0.928 2.479,0.928 2.41,0.928 false 2.778,0.658 2.778,0.797 2.778,0.797 2.847,0.797 false

Remove the S-HORN relay from engine room relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 When auxiliary battery voltage is not applied between terminals 1 and 2 10 kΩ or higher
3 - 5 When auxiliary battery voltage is applied between terminals 1 and 2 Below 1 Ω


Text in Illustration
*a S-HORN Relay



OK

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPLACE S-HORN RELAY

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the main body ECU (multiplex network body ECU) (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).

U190817E02
5.01,1.26 5.01,1.51 5.01,1.51 5.167,1.51 false 0.146,0.135 0.292,0.271 0.146,0.135 10 false *a 1.188,0.552 1.417,0.771 0.229,0.219 10 false 2C 4.792,0.552 5.021,0.75 0.229,0.198 10 false MB 5.198,1.448 5.49,1.646 0.292,0.198 10 false SH

Text in Illustration
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


b.

Disconnect the 2C instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2C-39 - MB-17 (SH) Always Below 1 Ω




OK

5.CHECK HARNESS AND CONNECTOR (AUXILIARY BATTERY - S-HORN RELAY)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (AUXILIARY BATTERY - S-HORN RELAY)
a.
B270907E01
0.088,0.064 0.244,0.202 0.156,0.138 10 *a

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Engine room relay block and junction block assembly S-HORN relay terminal 1- Body ground Always 11 to 14 V
Engine room relay block and junction block assembly S-HORN relay terminal 5 - Body ground Always 11 to 14 V


Text in Illustration
*a Engine room relay block and junction block assembly



OK

6.CHECK HARNESS AND CONNECTOR (S-HORN RELAY - SECURITY HORN ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (S-HORN RELAY - SECURITY HORN ASSEMBLY)
a.
B270907E01
0.088,0.064 0.244,0.202 0.156,0.138 10 *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Engine room relay block and junction block assembly S-HORN relay terminal 3 - A70-1 Always Below 1 Ω
Engine room relay block and junction block assembly S-HORN relay terminal 3 - Body ground Always 10 kΩ or higher


Text in Illustration
*a Engine room relay block and junction block assembly



OK

7.CHECK HARNESS AND CONNECTOR (S-HORN RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (S-HORN RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.
B270907E01
0.088,0.064 0.244,0.202 0.156,0.138 10 *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Engine room relay block and junction block assembly S-HORN relay terminal 2 - 2C-39 Always Below 1 Ω
Engine room relay block and junction block assembly S-HORN relay terminal 2 - Body ground Always 10 kΩ or higher


Text in Illustration
*a Engine room relay block and junction block assembly



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR