Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM › 2014.11–2020.08
RM2070E _58 Vehicle Interior _061938 THEFT DETERRENT / KEYLESS ENTRY _0301770 THEFT DETERRENT SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  Glass Breakage Sensor Circuit  


DESCRIPTION

When the main body ECU (multiplex network body ECU) detects that the glass breakage sensor (quarter window assembly RH, quarter window assembly LH or back door glass) is broken, the theft deterrent system switches from the armed state to the alarm sounding state.

WIRING DIAGRAM

B384276E03
5.135,2.479 6.781,2.885 1.646,0.406 10 false Main Body ECU (Multiplex Network Body ECU) 3.948,1.375 5.021,1.854 1.073,0.479 10 false Instrument Panel Junction Block Assembly 0.938,1.531 2.979,1.833 2.042,0.302 10 false Glass Breakage Sensor (Quarter Window Assembly RH) 5.219,0.854 5.667,1.167 0.448,0.313 10 false GPBS 5.135,2.313 5.385,2.469 0.25,0.156 10 false MB 2.073,0.74 2.458,0.885 0.385,0.146 10 false SSR+ 1.458,0.729 1.833,0.969 0.375,0.24 10 false SSR- 3.979,0.844 4.177,1.021 0.198,0.177 10 false 2B 3.979,0.646 4.25,0.979 0.271,0.333 10 false 15 0.938,1.375 1.229,1.604 0.292,0.229 10 false S35 2.594,0.74 2.688,0.875 0.094,0.135 10 false 1 1.208,0.75 1.302,0.885 0.094,0.135 10 false 2 0.927,3.958 3,4.521 2.073,0.563 10 false Glass Breakage Sensor (Quarter Window Assembly LH) 3.448,4.125 4.948,4.49 1.5,0.365 10 false Glass Breakage Sensor (Back Door Glass) 2.146,3.323 2.5,3.469 0.354,0.146 10 false SSR- 1.427,3.323 1.854,3.531 0.427,0.208 10 false SSR+ 2.563,3.417 2.865,3.719 0.302,0.302 10 false R38 1.073,3.417 1.365,3.625 0.292,0.208 10 false R37 2.667,3.24 2.76,3.375 0.094,0.135 10 false 1 1.167,3.24 1.26,3.375 0.094,0.135 10 false 1 4.958,0.74 5.146,0.938 0.188,0.198 10 false 19 3.667,3.323 4.094,3.563 0.427,0.24 10 false SSR+ 3.49,3.323 3.594,3.469 0.104,0.146 10 false 1 3.448,3.958 3.708,4.104 0.26,0.146 10 false V12

PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

According to the display on the GTS, read the Data List.

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Sealed Glas Brak Sen Glass breakage sensor connecting/With or Without With: Glass breakage sensor connected
Without: Glass breakage sensor not connected
-

OK:

With appear on the tester screen.




OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

2.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
2.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the main body ECU (multiplex network body ECU) (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).

U125019E01
0.178,0.125 0.349,0.269 0.172,0.144 10 *a 1.313,0.536 1.500,0.673 0.187,0.137 10 2B 4.816,0.529 5.041,0.666 0.225,0.137 10 MB 4.716,1.53 5.122,1.669 0.406,0.140 10 GPBS 5.246,1.261 5.246,1.597 5.246,1.597 5.124,1.597 false


Text in Illustration
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -

b.

Disconnect the 2B instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2B-15 - MB-19 (GPBS) Always Below 1 Ω




OK

3.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - QUARTER WINDOW ASSEMBLY RH)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - QUARTER WINDOW ASSEMBLY RH)
a.

Disconnect the S35 glass breakage sensor (quarter window assembly RH) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2B-15 - S35-1 (SSR+) Always Below 1 Ω
S35-1 (SSR+) - Body ground Always 10 kΩ or higher




OK

4.CHECK HARNESS AND CONNECTOR (QUARTER WINDOW ASSEMBLY RH - QUARTER WINDOW ASSEMBLY LH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (QUARTER WINDOW ASSEMBLY RH - QUARTER WINDOW ASSEMBLY LH)
a.

Disconnect the R37 glass breakage sensor (quarter window assembly LH) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S35-2 (SSR-) - R37-1 (SSR+) Always Below 1 Ω
R37-1 (SSR+) - Body ground Always 10 kΩ or higher




OK

5.CHECK HARNESS AND CONNECTOR (QUARTER WINDOW ASSEMBLY LH - BACK DOOR GLASS)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (QUARTER WINDOW ASSEMBLY LH - BACK DOOR GLASS)
a.

Disconnect the R38 glass breakage sensor (quarter window assembly LH) connector.


b.

Disconnect the V12 glass breakage sensor (back door glass) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R38-1 (SSR-) - V12-1 (SSR+) Always Below 1 Ω
V12-1 (SSR+) - Body ground Always 10 kΩ or higher




OK

6.INSPECT GLASS BREAKAGE SENSOR (QUARTER WINDOW ASSEMBLY RH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT GLASS BREAKAGE SENSOR (QUARTER WINDOW ASSEMBLY RH)
a.

Measure the resistance according to the value(s) in the table below.

B384270E02
5.396,0.604 5.802,0.896 0.406,0.292 10 false *a

Text in Illustration
*a Component without harness connected
(Glass Breakage Sensor (Quarter Window Assembly RH))
- -

Standard Resistance:
Tester Connection Condition Specified Condition
1 (SSR+) - 2 (SSR-) Always Below 1 Ω




OK

7.INSPECT GLASS BREAKAGE SENSOR (QUARTER WINDOW ASSEMBLY LH)

NG

REPLACE GLASS BREAKAGE SENSOR (QUARTER WINDOW ASSEMBLY RH)

7.INSPECT GLASS BREAKAGE SENSOR (QUARTER WINDOW ASSEMBLY LH)
a.
B313243

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (SSR+) - 1 (SSR-) Always Below 1 Ω




OK

REPLACE GLASS BREAKAGE SENSOR (BACK DOOR GLASS)

NG

REPLACE GLASS BREAKAGE SENSOR (QUARTER WINDOW ASSEMBLY LH)