Home › Vehicle Exterior › WINDOW / GLASS › BACK DOOR GLASS › 2012.03–2016.05
RM2070E _59 Vehicle Exterior _061949 WINDOW / GLASS _0301872 BACK DOOR GLASS A

WINDOW / GLASS  BACK DOOR GLASS  REMOVAL  


PROCEDURE

Hide 64886 1.REMOVE BACK WINDOW GLASS CHANNEL LH

Hide 64885A 2.REMOVE BACK WINDOW GLASS CHANNEL RH

Hide 67939B 3.REMOVE BACK DOOR CENTER GARNISH

Hide 67938A 5.REMOVE BACK DOOR SIDE GARNISH LH

Hide 67937B 6.REMOVE BACK DOOR SIDE GARNISH RH

Hide 67750 7.REMOVE BACK DOOR TRIM BOARD ASSEMBLY

Hide 85292A 8.REMOVE REAR WIPER ARM HEAD CAP

Hide 9.REMOVE REAR WIPER ARM AND BLADE ASSEMBLY

Hide 85143R 10.REMOVE REAR WIPER MOTOR GROMMET

Hide 85110R 11.REMOVE REAR WIPER MOTOR ASSEMBLY

Hide 68131 12.REMOVE BACK DOOR GLASS

a.
B291624E01
0.238,0.629 0.396,0.778 0.157,0.149 10 *1 0.756,0.801 0.425,0.709 false

Apply protective tape to the outer surface of the vehicle body to prevent scratches.

Text in Illustration
*1 Protective Tape

NOTICE:

When separating the back door glass from the vehicle, be careful not to damage the paint or interior and exterior ornaments.



b.
B291625E01
1.389,0.851 1.546,1.000 0.157,0.149 10 *1 1.665,0.417 1.48,0.417 1.48,0.417 1.48,0.838 false 1.665,0.736 1.48,0.736 false

Place matchmarks on the back door glass and vehicle body on the locations indicated in the illustration.

Text in Illustration
*1 Matchmark

HINT:

Matchmarks are not necessary if the back door glass is not going to be reused.



c.
B274723

Disconnect the 2 connectors.


d.
B291626E01
1.383,0.84 1.540,0.989 0.157,0.149 10 *1 1.106,0.773 1.366,0.916 false

Pass a piano wire between the vehicle body and back door glass from the interior as shown in the illustration.

Text in Illustration
*1 Piano Wire


e.

Tie both wire ends to wooden blocks or similar objects that can serve as handles.

NOTICE:

When separating the back door glass from the vehicle, be careful not to damage the paint or interior and exterior ornaments.



f.

Cut off the adhesive by pulling the piano wire around the back door glass.

NOTICE:

Leave as much adhesive on the vehicle body as possible when removing the back door glass.



g.
B291627

Using suction cups, disengage the 2 clips and remove the back door glass.


Hide 64818C 13.REMOVE NO. 1 BACK WINDOW GLASS SPACER

a.

When reusing the back door glass:

i.
B274726E01
0.18,0.147 0.381,0.310 0.201,0.164 10 *A

Using a scraper, remove the No. 1 back window glass spacer.

Text in Illustration
*A Back Side

NOTICE:
·

Be careful not to damage the back door glass.

·

Be sure to replace the No. 1 back window glass spacer with a new one.





Hide 64819 14.REMOVE NO. 2 BACK WINDOW GLASS SPACER

HINT:

Use the same procedure as for the RH side.


Hide 75575D 15.REMOVE BACK WINDOW LOWER MOULDING

a.

When reusing the back door glass:

i.
B274727E01
0.181,0.135 0.387,0.308 0.207,0.173 10 *A

Using a scraper, remove the back window lower moulding.

Text in Illustration
*A Back Side

NOTICE:
·

Be careful not to damage the back door glass.

·

Be sure to replace the back window lower moulding with a new one.





Hide 75573G 16.REMOVE NO. 1 BACK WINDOW OUTSIDE MOULDING RH

a.

When reusing the back door glass:

i.
B274728E01
0.18,0.165 0.346,0.314 0.166,0.148 10 *A

Using a scraper, remove the No. 1 back window outside moulding RH.

Text in Illustration
*A Back Side

NOTICE:
·

Be careful not to damage the back door glass.

·

Be sure to replace the No. 1 back window outside moulding RH with a new one.





Hide 75574C 17.REMOVE NO. 1 BACK WINDOW OUTSIDE MOULDING LH

HINT:

Use the same procedure as for the RH side.


Hide 68294A 18.REMOVE BACK DOOR GLASS ADHESIVE DAM

a.

When reusing the back door glass:

i.
B274729E01
0.18,0.143 0.387,0.309 0.207,0.166 10 *A

Using a scraper, remove the back door glass adhesive dam.

Text in Illustration
*A Back Side

NOTICE:
·

Be careful not to damage the back door glass.

·

Be sure to replace the back door glass adhesive dam with a new one.





Hide 68131 19.CLEAN BACK DOOR GLASS

a.

Using a scraper, remove the adhesive tape and adhesive sticking to the back door glass.

NOTICE:

Be careful not to damage the back door glass.



b.

Clean the outer circumference of the back door glass with a non-residue solvent.

NOTICE:
·

Do not touch the back door glass surface after cleaning it.

·

Even if using a new back door glass, clean the back door glass with a non-residue solvent.




Hide 20.CLEAN VEHICLE BODY

a.
B149737E07
2.311,1.537 2.44,1.663 false 0.934,1.646 1.160,1.799 0.226,0.152 10 *1 0.867,1.52 0.997,1.646 false 0.96,0.674 0.839,0.488 0.839,0.488 0.637,0.488 false 2.533,0.673 2.604,0.743 2.604,0.743 2.744,0.743 false 2.433,1.715 2.660,1.867 0.226,0.152 10 *1 0.417,0.419 0.643,0.572 0.226,0.152 10 *2 2.801,0.69 3.027,0.842 0.226,0.152 10 *2

Using a scraper, remove the moulding and adhesive from the back window fix glass.

Text in Illustration
*1 Adhesive
*2 Vehicle Body


b.

Clean and shape the contact surfaces of the vehicle body.

i.

Using a knife, cut away excess adhesive on the contact surfaces of the vehicle body, as shown in the illustration.

NOTICE:

Be careful not to damage the vehicle body.


HINT:

Leave as much adhesive on the vehicle body as possible.



ii.

Clean the contact surfaces of the vehicle body with a piece of cloth saturated with cleaner.

HINT:

Even if all the adhesive has been removed, clean the vehicle body.